Thank u for the simple and correct explanation of the controller hook up..theres to many videos of the wrong way to do something it's nice of u to get straight to the project.and without the crappy music sound track..thanks again..im trying to build a beast of a bike....
Thank you I am having difficulty understanding what all the wires are for but this simplifies things somewhat, I will have another go tomorrow following your guidance 👏👏👏👏👏
Thanks for the video. Some ideas : Arduino touch display : including watt meter (W, V, A, Wh used, Wh/km), speed and trip, remaining trip, motor temperature, main on/off, throttle control for limited speed and current, controlled front and rear light by luminosity and e brake, bms analyser with cellule voltages, bms temperature, Usb c phone charger Low voltage cut off modification (for better life cycles) Shunt resistance measurement for accurate reading of consumption (which depends if watts measured from controller) You asked for ideas, there you have it. 😃
Sir - thank you very much for making this video. I have been working on a electric trike I bought very very cheap. It was left for a couple of years. This video has given me better understanding of what IM looking for. Only problem is that there are no labels on the wires and the controller is labelled in Chinese. At least now I have a starting point. Thank you.
The high brake requires a separate 12-volt battery. The low brake is not a real brake at all. All it does is shut off electricity to the motor when you pull on the regular handlebar brake lever. That way the motor is not trying to make you go even thou you have activated the handlebar brake lever.
Hi I been watching all you videos they're really helpful do you any video how to explain how add any 12v converter to add LED lights or turn signals? I will appreciate you help thanks.
Hey can you please help me. Ive a hub motor from a 2 wheel self balancing hoverboard and a motor controller (both 3 phase). So i want to control the hub motor with a gyroscope (MPU-6050) in both the directions. So if i have an output from -5V to +5V, how could i control the hub motor in both the directions. For eg- with +5V i want it to go clockwise and with -5V anticlockwise direction. It would be a great help!
Thank you very much for all the explanations. I ordered a controller, but it came without instructions. I realize where the battery is connected and the throttel I don't know which wires command the engine to start and stop. Now I saw. Thanks for the help!
This really explains all the components well, that's for the effort that went into making the video. I watched it to help me find a power problem with my bike as when I click Low setting to Medium there is a power increase as you'd expect but then when I click to High I can hear it click in but only for a fraction of a second. I had the battery tested as I thought there was a bad cell or two when demanding more power as in High mode but the battery is fine. Any where else I should be looking please? Thank you.
Very nice, thanks for putting the vid and visual aid together! I've repaired and worked on cars, motorcycles, amplifiers, etc., and had questions about how electric scooters and bikes were put together, this is very helpful. It would be nice if the manufacturers had a shop manual and a schematic available. In theory an electrically driven vehicle should be easier to repair and last longer.
Great video very helpful. Does the controller with no hall sensor work on a motor with a hall sensor? My controller is 50amps dualtron_x2 no hall sensor, and my motor is LD 3200watts with a hall sensor.
Hi I have to say I learned a lot from your really detailed videos, and they are fantastic video :) , I would love to see a video on how to create crus control on the controller that doesn't have any crus control
Thank you very much for the excellent ideas, and I want to ask you is it possible to connect a motor that works on a current of 36 volts to a current of 48 volts or more
A few questions. Is highbrake always connected to plus from the battery (are all or most controllers similar in this case)? Can i use high and low brake together / simultanious? my idea is Lowbrake at the standard switch from the brake leaver and highbrake at a button to use it only when i want to. The question is, can i press the highbrake button at the same time i pull the brake which connects lowbrake, or might this damage anything insider the controller? Thanks for your answer in advance
Hi... To activate high brake will work only when is connected to High pole of battery... now to connect them in same time.... i don't know because i never try it, but i think it will work at 90% without problem... But I promise you that I will try it.
@@EVCustoms thank you for this quick response. I would love to see a video of your testing board when you test this. Thank you very much. I like your videos. I learn a lot from your channel.
Thank you for your videos, they have help me a lot. I have a question i replaced a controler in a mini scooter, is alreay everything working thanks to your explinations, except the 3 speed, but my question is if its normal for the motor cables to gain heat,? havent run the scooter only acelerate a bit for testing, the motor noise seems normal, but i find the cables to hot.
Do you have an experience with square waves from dualtron, I want to dig in their code and try to see if I can find out their assembly and overclock them, would that be possible
hi ! great indication ! question !! if the wired wrong main power line plus for minus and minus for plus ... for fraction a second .. controler is iremediable broken !?
that was good thank you very much...does the 3 speeds controll voltage to the motor? and is there a brake lever that can do proportional braking rather than on off regen?
Great video. Very much appreciated. I have a pad on the board labeled EBS. It has 5 volts on it. Does it need to be grounded to enable regen? How ca I tell if it working?
Fantastic set up. I made something similar years ago to teach young soldiers electrical troubleshooting on vehicles. That way they could learn how to diagnose before spending tax dollars just replacing parts. lol
This is I looking for,thank you very much🙏🙏🙏 sir,I can now start fixing my scratch motorbike,only I need is controller and charger,sir can I ask what if the batery is not working they have a way to fix it,thank you
Very good vedeo ,I studied meny things ,,thanks lot sir ,,please give us schematic detailed vedeo about this lesson is highly appreciate ,,thanks and expect the next vedeo
Out standing videos 👍👍👍 I like these kinda videos 👍👍 buddy good job most EBike Kit's have poor installing manual and the wires are not marked so it's hard to hook up now all I need to know is how to fix power to the throttle and Hall sencer burnd out no power to motor and throttle????? Or how to fix control box??? Hope you can help thanks 😊👍 buddy good job.
its ok,I used (2)52v battery packs 20a fuse popped as soon as i left ,25a wowww then that popped i dont know why,well i still have 30,35 & 40amp fuses left to try.
A warm hello from the Philippines! Thank you for the very informative presentation & straightforward explanation. Pls. show us how to connect the 48V supply to power 12V lighting system using the converter as presented in your video. TIA.
Hi, thank you for your video very helpful but I have a question, when I connect up the wiring as per the video I still have no connection for the green black and red terminals from the motor as well as a thin blue wire from the throttle can you help please ? TIA
Excellent video. I can see you have poured in much effort and time to making this very good video. It will be even better without the background music. Thank you for sharing. I have LIKED and SUBSCRIBED.
Question. I have a small foldable ebike. It has a 180w 24v motor. It goes way to slow. I need to replace the battery and the controller anyway because I want a trothle and the battery is worn out. To take as much as possible advantage of this swap. What combination will make the bike go faster? Can i put more voltage on the motor and what will be the max voltage?
Awesome idea, great way to show how it all works. I would be interested in a video that shows how to identify the wires without opening the controller. Is that possible?
@@EVCustoms thanks for the reply, do you mean frequency leaving the controller going to the 3 phases? i bought a 80 amp controller and never connected the speed controller, so i guess its in "middle speed", but it maxes at at 67amps. the seller told me once i put the speed selector into "high speed" and fully twist the throttle i will get 80 amps. do you think this is true?
What is the potentiometer spec’d to? I’m doing a mower conversion and I’d like to use a potentiometer as the throttle and have a normally closed switch hooked up to the brake. That way the operator prescience bail will open the circuit when pressed to turn it on and the motor will stop when let go of.
Hello, I have a Bolt Pro and I put a new twist throttle with a key ignition that took the place of the cruise control button. Now that I have no cruise control button I can't turn the LED Headlight on. I would like to have the OEM button on the left handlebar be the cruise and headlight trigger but unsure how to connect it to the controller and work that way. Got any tips or a step by step you could help me with? Thanks and happy Thanksgiving.
I have safety questions! I am doing research for a motorcycle install and I am trying to figure out where and how to install a kickstand safety switch. I believe it is normally open while the kickstand is down. Also, for hubs with regenerative braking, how would it be wired so the rear brake light turns on? Thanks in advance!
Beautiful and very simple explanation, I truly loved it. I have been looking all over on how to charge the batteries at home? Do you have any videos for that? Please let me know.
Hi. I wonder if you can tell me please if I run a 48v motor on a 36v battery if it’s going to damage anything or if the battery can handle it? Thank you very much in advance.
awesome video! I have a dual motor set up with 2 controllers. im wondering how I can get the throttlen to move both wheels at the same time...currently I took the signal wire of one controller & integrated it in with the other controller...one wheel spins, I release the throttle, & depending on how slowly I open the throttle in the next engagement of motors both wheels will turn, buts trying to find a sweet spot on the throttle for both to turn...opening widely itll just go to spin either wheel without the other turning...any help would greatly be appreciated
With defective hall sensor most probably if the controller is from good ones it will hit error and cut the power from the motor, if the controller is from cheap ones... most propably it will burn the motor, if the motor is high power then will burn the MOSFET of the controller.
Thank you for the video, it is very helpful. I recently upgraded my 1000 watt Voilamart DIY ebike to the 1500 watt kit. My original kit has the LCD display showing battery power and speed of the bike. The new kit only has a LED bar graph on the throttle with no LED display for speed. Is it possible to wire in the original display Model SW900 to the new system? The new controller is bigger and has no connector for a display. Thank you.
Thank you very much for the great video. I learned a lot. But please tell me why is the engine making this loud noise? My replacement controller sounds exactly the same, while the original controller installed in my scooter is much quieter. I hope you or someone else can help me. Best regards
Nice video. I am wondering how a controller like that contains the regeneartive braking feature by holding the mechanical brake? . Does it?. Because normal controllers does not have this feature inside it.
@@EVCustoms This braking is electrical brake. Controlling the stoappage electrically does not necessarily means that battery will charged. However, I think you are refering for having an electrical brake that disppates energy by passive element rather than having a mechanical brake system. Let me know about you opinion SIr , Thank you !
@@Abdalrahman_Yahya There is no any passive element (load resistor) in controller, all regen braking futures always charge the battery with a low amount of energy...
@@Abdalrahman_Yahya There is two ways, first one is just disconnect the motor when you braking and second one breaking via motor an charge the battery at breaking..
Hi i have change a controller on. Ebike and i cant do this work properly and i have 3 cables red, black and grey and I don’t know what they are to connect
Do you know whether the ignition signal can be powered up prior the main power feed is connected or does the main power need to be supplied for the ignition circuit to work? I wonder whether these are separate from one another. Thank you
Thanks!
Thank you too Edward!! 👍😁
Thank u for the simple and correct explanation of the controller hook up..theres to many videos of the wrong way to do something it's nice of u to get straight to the project.and without the crappy music sound track..thanks again..im trying to build a beast of a bike....
Hi. Can you help me fix my fat scooter? Throttle not doing anything. Bike won't move
That may be the best presentation I've seen
Thank you I am having difficulty understanding what all the wires are for but this simplifies things somewhat, I will have another go tomorrow following your guidance 👏👏👏👏👏
I enjoyed your tutorial . I'm in my early sixties trying to learn about e-bikes. Thanks
Πολυ ωραιο βιντεο, ωραια διαταξη πειραματισμου, εξαιρετική παρουσιαση!
Eyxaristw polu file mou!
Thanks for the video.
Some ideas :
Arduino touch display : including watt meter (W, V, A, Wh used, Wh/km), speed and trip, remaining trip, motor temperature, main on/off, throttle control for limited speed and current, controlled front and rear light by luminosity and e brake, bms analyser with cellule voltages, bms temperature, Usb c phone charger
Low voltage cut off modification (for better life cycles)
Shunt resistance measurement for accurate reading of consumption (which depends if watts measured from controller)
You asked for ideas, there you have it. 😃
Oh my god...!!! you predicted all the work i do these days from touch screen arduino to shunt!!!!
This project is on the way...!
Great video! I'm using my first controller with an ignition switch, and wasn't sure what to do. Perfect!
Thanks Teacher! love every detail of what your teaching helps a lot with my current project.
Sir - thank you very much for making this video. I have been working on a electric trike I bought very very cheap. It was left for a couple of years. This video has given me better understanding of what IM looking for. Only problem is that there are no labels on the wires and the controller is labelled in Chinese. At least now I have a starting point. Thank you.
hi. what is "high brake"? and how to connect it? to "gnd" to "positive bat"? thanks for the video & for your replay
The high brake requires a separate 12-volt battery. The low brake is not a real brake at all. All it does is shut off electricity to the motor when you pull on the regular handlebar brake lever. That way the motor is not trying to make you go even thou you have activated the handlebar brake lever.
Hi I been watching all you videos they're really helpful do you any video how to explain how add any 12v converter to add LED lights or turn signals? I will appreciate you help thanks.
I will made learning board videos with dc to dc converters soon as possible,, so stay tuned..;)
My parrot and dog was watching with me,. U explained everything so clearly that even they can do it as well ,🤣 💯🌟
Hahaha..! than you man I appreciate it..
Pmsl you still ended up here tho
Shit so did I
Really nice presentation board of showing the basic connections for hub and controllers. Keep up the good work!
Thank you mate!
Hey can you please help me. Ive a hub motor from a 2 wheel self balancing hoverboard and a motor controller (both 3 phase). So i want to control the hub motor with a gyroscope (MPU-6050) in both the directions. So if i have an output from -5V to +5V, how could i control the hub motor in both the directions. For eg- with +5V i want it to go clockwise and with -5V anticlockwise direction. It would be a great help!
Thank you very much for all the explanations.
I ordered a controller, but it came without instructions.
I realize where the battery is connected and the throttel I don't know which wires command the engine to start and stop.
Now I saw.
Thanks for the help!
Thank you for your video!
I understand how to use wheel in motor.
But I can’t understand English .
So I will continue to watch your video .
I understand !
I'll translate for you. in what language do you want
@@John_Smile Thank you.
I want to translate it into Japanese.
Very simple, useful and informative!!!! Thats what a beginner needs
My DC Metro is not working not sure why
Great Great Job. Excellent presentation. Every detail. Perfect
Thanks you very much...
This really explains all the components well, that's for the effort that went into making the video. I watched it to help me find a power problem with my bike as when I click Low setting to Medium there is a power increase as you'd expect but then when I click to High I can hear it click in but only for a fraction of a second. I had the battery tested as I thought there was a bad cell or two when demanding more power as in High mode but the battery is fine. Any where else I should be looking please? Thank you.
Very nice, thanks for putting the vid and visual aid together! I've repaired and worked on cars, motorcycles, amplifiers, etc., and had questions about how electric scooters and bikes were put together, this is very helpful. It would be nice if the manufacturers had a shop manual and a schematic available. In theory an electrically driven vehicle should be easier to repair and last longer.
Wow, really well explained.
I would love to see a video on speedlimiters/derestricting.
Great video very helpful.
Does the controller with no hall sensor work on a motor with a hall sensor?
My controller is 50amps dualtron_x2 no hall sensor, and my motor is LD 3200watts with a hall sensor.
Yes all of them can work with motors with hall sensors..
Can I still use that controller to a motor that is not brushless? For example the angle grinder
Dude thank you so much for this video. Easy to understand. Thanks again!
Hi I have to say I learned a lot from your really detailed videos, and they are fantastic video :) , I would love to see a video on how to create crus control on the controller that doesn't have any crus control
You must made exactly same procedure..
Love the hardwork of yours it's easy to learn like this
Thank you very much for the excellent ideas, and I want to ask you is it possible to connect a motor that works on a current of 36 volts to a current of 48 volts or more
Yes you can do that but you must watch temperature of the motor..
@@EVCustoms thank you my dear
@@EVCustoms thank you my dear
Thanks a lot, friend. This video is a real service to others
A few questions. Is highbrake always connected to plus from the battery (are all or most controllers similar in this case)? Can i use high and low brake together / simultanious?
my idea is Lowbrake at the standard switch from the brake leaver and highbrake at a button to use it only when i want to. The question is, can i press the highbrake button at the same time i pull the brake which connects lowbrake, or might this damage anything insider the controller?
Thanks for your answer in advance
Hi... To activate high brake will work only when is connected to High pole of battery... now to connect them in same time.... i don't know because i never try it, but i think it will work at 90% without problem...
But I promise you that I will try it.
@@EVCustoms thank you for this quick response. I would love to see a video of your testing board when you test this. Thank you very much. I like your videos. I learn a lot from your channel.
Thank you for your videos, they have help me a lot.
I have a question i replaced a controler in a mini scooter, is alreay everything working thanks to your explinations, except the 3 speed, but my question is if its normal for the motor cables to gain heat,? havent run the scooter only acelerate a bit for testing, the motor noise seems normal, but i find the cables to hot.
Do you have an experience with square waves from dualtron, I want to dig in their code and try to see if I can find out their assembly and overclock them, would that be possible
Geia sou.. Christo send me your WhatsApp or Viber number.
Great! To reverse your pot throttle direction, swap the outer 2 wires. To reverse your motor direction, swap any 2 motor wires.
Yes you swap ,em
Best video I have seen so far
The way the breaks works won’t it stop the vehicle instantly? Instants stops can cause accident
It will not stop instantly when there's momentum from your weight.
hi ! great indication ! question !! if the wired wrong main power line plus for minus and minus for plus ... for fraction a second .. controler is iremediable broken !?
that was good thank you very much...does the 3 speeds controll voltage to the motor? and is there a brake lever that can do proportional braking rather than on off regen?
This was helpful, building e bike with engine front and rear.
Great video. Very much appreciated. I have a pad on the board labeled EBS. It has 5 volts on it. Does it need to be grounded to enable regen? How ca I tell if it working?
Yes it must be grounded, after that if you connect low brake wire to ground electronic brake must work..
What value is that potentiometer are you using for the throttle? Will a 10k pot work?
Fantastic set up. I made something similar years ago to teach young soldiers electrical troubleshooting on vehicles. That way they could learn how to diagnose before spending tax dollars just replacing parts. lol
But how do you ride this thing?
Fantastic thank you but I have a question how I can run a brush less motor like this with RC
This is I looking for,thank you very much🙏🙏🙏 sir,I can now start fixing my scratch motorbike,only I need is controller and charger,sir can I ask what if the batery is not working they have a way to fix it,thank you
Man your video is easy to follow.. i will sub
Very nice video, all is clear, lot of thanks for your time
You have some information about the red led codes of the kelly kbl72301X controller
Very good vedeo ,I studied meny things ,,thanks lot sir ,,please give us schematic detailed vedeo about this lesson is highly appreciate ,,thanks and expect the next vedeo
What happen if I use a motor controller for 1500w motor for a 1200w one? Or if I choose a less powerful one like 1000w?
Its 100% OK for your motor....
@@EVCustoms thanks!
great vid ,I'm looking to upgrade my 350w ebike 36v 13ahim not sure on what i could upgrade to? ,i would very much appreciate any advice
Out standing videos 👍👍👍 I like these kinda videos 👍👍 buddy good job most EBike Kit's have poor installing manual and the wires are not marked so it's hard to hook up now all I need to know is how to fix power to the throttle and Hall sencer burnd out no power to motor and throttle????? Or how to fix control box??? Hope you can help thanks 😊👍 buddy good job.
if you add another 60v battery pack would you use the same fuse for both
battery packs?......Thank you for reading my question
its ok,I used (2)52v battery packs 20a fuse popped as soon as i left ,25a wowww then that popped i dont know why,well i still have 30,35 & 40amp fuses left to try.
A warm hello from the Philippines! Thank you for the very informative presentation & straightforward explanation. Pls. show us how to connect the 48V supply to power 12V lighting system using the converter as presented in your video. TIA.
Thank you my friend.... i am trying to find some time ro make this video ...
Also please include how to wire the DC to DC module
Hi, thank you for your video very helpful but I have a question, when I connect up the wiring as per the video I still have no connection for the green black and red terminals from the motor as well as a thin blue wire from the throttle can you help please ? TIA
Hvala vam na korisnim savetima !
Excellent video. I can see you have poured in much effort and time to making this very good video. It will be even better without the background music. Thank you for sharing. I have LIKED and SUBSCRIBED.
Question. I have a small foldable ebike. It has a 180w 24v motor. It goes way to slow. I need to replace the battery and the controller anyway because I want a trothle and the battery is worn out. To take as much as possible advantage of this swap. What combination will make the bike go faster? Can i put more voltage on the motor and what will be the max voltage?
Very detailed video, easy to understand. Thank you. Great testing rig as well. Tnx.
Thank you mate!!
Great video. Thanks ! Can you explain how the three speed switch should be connected ?
Amazing!
Thank you for this in depth video explanation.
Awesome idea, great way to show how it all works. I would be interested in a video that shows how to identify the wires without opening the controller. Is that possible?
it seems like the 3 speed switch is changing the voltage, but does it also change the amps?
With 3 speed you change only the frequency... starting amps is same...
@@EVCustoms thanks for the reply, do you mean frequency leaving the controller going to the 3 phases? i bought a 80 amp controller and never connected the speed controller, so i guess its in "middle speed", but it maxes at at 67amps. the seller told me once i put the speed selector into "high speed" and fully twist the throttle i will get 80 amps. do you think this is true?
I am trying to build an ev outboard motor! Can you explain how that would work since the throttle control is forward neutral and reverse?
hi, great video 👍need advice 🙏 any idea why my low brakes button only stop power to wheel ( not braking at all) thank you
Hi... are you sure that your controller have regen (e-brake) function?
@@EVCustoms hi, i am not sure , it is this one www.aliexpress.com/item/32808852406.html?spm=a2g0s.9042311.0.0.56a64c4dENZsz4
My question is if i buy controller to incraces power will working?My bike come with 350w motor and 36v battery if replace with controller 48v ? Thanks
Hi... wheel size?
Excelente trabajo 👍 muy elaborado y práctico 👏👏👏. Saludos desde Argentina 🇦🇷🤗
very good video!
can i have ebrake always on? i would like to have brake on every time i my trottle get back to zero position! is that possible?
Well done to you what a fantastic hands on explanation made it so even I could understand it thank you keep the good work up
Thank you my friend ;)
What is the potentiometer spec’d to? I’m doing a mower conversion and I’d like to use a potentiometer as the throttle and have a normally closed switch hooked up to the brake. That way the operator prescience bail will open the circuit when pressed to turn it on and the motor will stop when let go of.
Do you have a video on how to connect the DC converter to the led light strip and headlights?
No yet my friend.. but it is on my video lost for future videos
Hello, I have a Bolt Pro and I put a new twist throttle with a key ignition that took the place of the cruise control button. Now that I have no cruise control button I can't turn the LED Headlight on. I would like to have the OEM button on the left handlebar be the cruise and headlight trigger but unsure how to connect it to the controller and work that way. Got any tips or a step by step you could help me with? Thanks and happy Thanksgiving.
08:17 button cablo,how many voltage? Please answer
My controller is not working.(high brake)
The video I was looking for. I applaud you for a very good video. Thank you.👏
nice video! Thanks from Brazil!
I have safety questions! I am doing research for a motorcycle install and I am trying to figure out where and how to install a kickstand safety switch. I believe it is normally open while the kickstand is down. Also, for hubs with regenerative braking, how would it be wired so the rear brake light turns on? Thanks in advance!
Beautiful and very simple explanation, I truly loved it. I have been looking all over on how to charge the batteries at home? Do you have any videos for that? Please let me know.
How is it when you have the controller inside the battery? How to test different components individually
hi love the vids how do i change the direction of the motor when changhing the phase wires
Hi.
I wonder if you can tell me please if I run a 48v motor on a 36v battery if it’s going to damage anything or if the battery can handle it?
Thank you very much in advance.
Hi... you can run 48v motor on 36v for sure... without any problem..
Thank you very much.
All the best.
awesome video! I have a dual motor set up with 2 controllers. im wondering how I can get the throttlen to move both wheels at the same time...currently I took the signal wire of one controller & integrated it in with the other controller...one wheel spins, I release the throttle, & depending on how slowly I open the throttle in the next engagement of motors both wheels will turn, buts trying to find a sweet spot on the throttle for both to turn...opening widely itll just go to spin either wheel without the other turning...any help would greatly be appreciated
i have a GIO 2 wheel scooter , the controller is obsolite , just wondering if a similar controller could be built
does a bad hall sensor damage the controller? how about a burned engine? does it damages the controller
With defective hall sensor most probably if the controller is from good ones it will hit error and cut the power from the motor, if the controller is from cheap ones... most propably it will burn the motor, if the motor is high power then will burn the MOSFET of the controller.
if you have motor without holl sensors can you used this controlle ??
Cool man, Nice job and very simple to understand...thank you.
Hello friend, what potentiometer you use ? i want to create an adjustable hidden button throttle ... :)
Hi... for speed limit?
@@EVCustoms i want to hide a potentiometer and button since throttle is illegal in EU :)
@@Boemel Yes i know.. i have old video how to do that.. button and potentiometer
Thank you for the video, it is very helpful. I recently upgraded my 1000 watt Voilamart DIY ebike to the 1500 watt kit. My original kit has the LCD display showing battery power and speed of the bike. The new kit only has a LED bar graph on the throttle with no LED display for speed. Is it possible to wire in the original display Model SW900 to the new system? The new controller is bigger and has no connector for a display. Thank you.
Hi... as your controller has no display wires,, that means is not compatible with LCD screens.... sorry man..
@@EVCustoms Thank you for your help.
You can wire the display directly to the battery for it to show the battery voltage.
Hello, How to run brushless motor with this controller as mentioned in your above video without hall effect wires? Thank you!
Hi.. to do that your controller must have this halsses option, many controller cannot work with out hallsensors..
Excellent presentation, Keep up your research work. Thank you for this upload. I liked it.
I have hiboy s2 pro. Is there a speed limiter connected to this controller? Like is there a cable I can cut that will enable my scooter to go faster?
Is there a way to connect piezo (buzzer) to the signal lights so that I can if there on?
Hi! Great video! Can you please tell me if I can use a 36v 11ah with a 36v 10,04ah battery? Please
you are the best man on earth! thank you so much
do i put my little orane ignition wire directly on to y 72 volt positive wire
Nice video, very useful for beginners. Keep up the good work!
Thank you very much for the great video. I learned a lot. But please tell me why is the engine making this loud noise? My replacement controller sounds exactly the same, while the original controller installed in my scooter is much quieter. I hope you or someone else can help me. Best regards
If it make to muchi noise,,. you must try to make some compilations with hall sensor wires and power wire of motor, until the motor runs smoothly..
Many thanks for the quick response. I will try it at some point.
Unfortunately, swapping them was unsuccessful. Is there another point that should be considered?
Hello sir! Which part was battery charger connected?
Nice video. I am wondering how a controller like that contains the regeneartive braking feature by holding the mechanical brake? . Does it?. Because normal controllers does not have this feature inside it.
90% of controllers and more,, have regen braking feature...
@@EVCustoms This braking is electrical brake. Controlling the stoappage electrically does not necessarily means that battery will charged. However, I think you are refering for having an electrical brake that disppates energy by passive element rather than having a mechanical brake system. Let me know about you opinion SIr , Thank you !
@@Abdalrahman_Yahya There is no any passive element (load resistor) in controller, all regen braking futures always charge the battery with a low amount of energy...
@@Abdalrahman_Yahya There is two ways, first one is just disconnect the motor when you braking and second one breaking via motor an charge the battery at breaking..
Hey again, how do I find the hall wires for the ninebot f25?
Hi i have change a controller on. Ebike and i cant do this work properly and i have 3 cables red, black and grey and I don’t know what they are to connect
Do you know whether the ignition signal can be powered up prior the main power feed is connected or does the main power need to be supplied for the ignition circuit to work? I wonder whether these are separate from one another. Thank you
Excellent Video that anyone (even me!) can follow - Thank You 10 / 10
Thank you Steve..
How would you derestrict the speed limit?
Can you show how to wire up a Kelly qskls 7230sf controller plz!
My onyx stopped working and they went out of business so it’s no longer working