I bought one of these controllers. I think I fried it using the the hover board battery. What is the maximum size battery I can use with this control unit. I was also wondering if I can use a 19 V DC power supply with it instead of the battery. I’m looking to make a large rock Tumblr with it and I need constant power for weeks. Please let me know your thoughts on this. I would really appreciate it. Thank you very much.
I have the same controller but I am trying to develop braking when changing direction, since the code waits for it to finish turning to change direction.
5:25 La placa trae dos reguladores uno 317 y el otro 7805, ninguno de los dos soportan mas de 36v en sus entradas de tension, por lo que vi en los datasheets los transistores si son hasta 70v, creen que cambiando la resistencia 1000 SMD que alimenta los reguladores podre poner una bateria de 42v comunes en patinetes y hover board?
To slow the motor use dynamic breaking. Power to zero. Short 2 of the 3 wires together and it will come to a stop, the motor will induce current in the coils, causes dynamic breaking. But it takes motion to do this. So the effect stops when the motor does
Thanks for this! I'm about to try it with the 36V hoverboard lipo. Can you explain why it fried your board? They should be able to take 36V? They say to add heatsinks to the MOSFETs over 60W, did you try that? I'm trying a similar "DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board LJ" $10 board.
You say that the battery of the hoverboard itself wil fry the board, but does that also apply if you're running 2 of the motors on only the battery from the hoverboard itself?
Hello, I'm Orlando Tristão, I'm from Portugal and I'm in a wheelchair. Congratulations on this video, no doubt many will benefit from your project. Please help me if you feel well. I need to adapt two Hoverboard motors, (36V 500W), to my wheelchair. I need to know which controller is ideal and how I can connect a joystick. Could you please help me? I await your dear reply. a hug, thank you very much
Did you test it with initial torque? I tested this controller and it have problems to start when wheel is under a load (initial torque). In your video all rotation tests is in "free wheel" condition so it starts smoothly. But when wheel is under the little load controller has problems to start (it just jumping back-forward). Just start rotation in slow rate and try stop it by hand, it has no torque-control loop.
I have a working hoverboard motor (tested on another system ) , I have purchased a brand new 36v controller with lcd ( s866 ) brand new throttle and brand new hoverboard battery for my e bike project but I'm experiencing no throttle issues I have checked voltage and purchased 3 brand new throttles checked wires tried swapping around but still no throttle
I thought he said he was going to do another video to follow through with this one? Can you please make that video :) Thumbs up if you want to see him wire this up with the uno and ESP3266!
hi, so if i had to power this with a power supply instead of a battery i need a 14,8 volt and 2,3 amps power supply it will work ? can someone please tell me if i am right ?
I don't normally comment but thanks.. best explained and actually can now test mine my LCD broken with throttle and trying to by passing it to a new throttle without lcd ..
You said this board can not generate any breaking torque. How would you recommend slowing the wheel. I have that wheel and board and want to make an electric skateboard. Its all set up and works, but now i want to add breaking. Do i need a different board. If so, which one?
I'm curious about the Hall Sensors, do they need to be connected? It's not like a BLDC controller needs Hall sensors to run, they can easily run in sensor less mode. Hall sensors are more about information on the running motor such as direction and speed. Its possible to adjust a BLDC motor just using the phase wires and looking at current draw/feedback but there are numerous other variables both static and dynamic that increase complexity and ultimately limit effectiveness. Hall sensors can provide detailed position information which certainly improves the ability to tune a BLDC's performance, however there are many many different kinds of Hall Sensor based on measured parameters and abilities of detection. Hall sensors can just detect, or provide position, they act as momentary switches, or as latch switches. I have ordered similar controller boards, but the documentation is utterly void of any specifics regarding the Hall Sensors... It makes some comment about motor being different, parents paying attention, and my drive plate will burn.... While its possible they are trying to say: If you drive your parents car faster than they do, they will burn your dinner and serve it to you on a plate, I suspect they intended something else. I believe this is a warning that when connecting call sensors you must be careful the connections don't overload (e.g.
Hi I want to make an electric quad using 4 hoverboard motors , if I want to control all of them from a single pod, I need to buy more board and connect them to a single pod and use 4 batteries with them? Or I can use one board with 4 motors and a single battery? Thanks in advance!
What pot size are you using please? I need to have a pot that will allow me to have the wheels just turning at walking speed for my golf trolley conversion project. I will be using two controllers with a double pole pot to try and get them balanced as much as possible.
For some reasons , I did everything that shown but nothing work.I thought had a bad board , change it twice and the third one still won't move the engine. Change the potentiometer , attached the VR to the 5volts connectors still nothing happened . I put the mother ack to the hoverboard ,all work fine . Anyone has any idea why s this happening ?
nice video, but I have a question my friend: is necessary connect the hall sensor? or Can I use without connect them? and also, I have a 24v DC motor brushless. but it have only 2 wires, red and black... Can I connect it motor 24 dc (2wires) in the board controller (3 phases) same as your video? I hope your reply. thanks!
This controller works with 3 phase motors only. You can buy a different version of this board that works without the hall sensors. You use Qunqi L298N Motor Drive Controller for 2 wire dc motor. Good luck.
I was using hoverboard's controller for tyres with a flysky i6 controller but now the issue I'm facing is board is not catching any signal from my transmitter can anyone guide me on this
I blew my controller and tried another still no throttle control i have potentiometer and Moffett z44-s please help i got my scooter scooter to run by the key and thats the only control I have on and off at a low speed, please help me figure this out. .
I have a 12v 0.18a 3wire blower dc blower fan, I want to slow the speed down for long periods but need the full speed for initial start up for a couple of minutes. Can you advise me on which type of small speed controller I should buy for the well being of my blower. Have seen vids on transistor/ potentiometer methods but would rather buy the right tool for the right job so to speak. Thankyou. Great video.
dear l just bought bldc motor controller exactly same as you have but unfortunately it does not give output power. input is 20V battery. no output voltage. do you have any comments? thanks
I wonder what the name of the module can be, the name, the number, the type or something, it is not enough to refer to the fact that it can be bought among the many 10,000 products.
Hi, as per your advice connected two controllers on two motors & one throttle. But again I am stuck in middle because I have no Reverse option in controllers. Any advice to modify controllers Reverse function without swapping wires? Appreciated.
I was wondering the same thing. I’m using mine to build a heavy duty rock tumbler so I don’t think I need as many volts. I’m not looking for speed. Looking for slow with a lot of torque. I’m hoping to run it on a 19 volt power supply. I tried to get the motor running using one of the other controller boards without the clip on wire leads on it. So I’m really hope this works as it’s getting expensive . I’m up over $35 on the 2 boards. Good luck with your build.
Hi, nice informative videos. Im planning to convert my hoverboard into gokart. Can you advise me if can connect both 350w motors parllel to one 350w controller. 2nd what gage wiring i should use. 3rd can the original battery of hoverboard be used. Thanks in advance.
Hoverboard batteries are known to go kaboom, so i would buy a better one You should be using 1 driver per motor unless the driver supports using multiple As for guage, use the same as the motor Also, it wouldn't be a fast gokart as hoverboard motors are slow Hope that helps!
no you cant put common heat sink! you must make all mosfet separatly, or use plastic isolator for screws or plastic screws and isolating layer between all of transistor and common heat sink (ex. kapton tape 2-3 layers). also check heat dissipation for linear stabilisator, if you use 24V and higher for power supply.
@@ledshowinindia6571 also right choice :) Insulating Washers is used in commercial driver for electric scooter and hoverboards. www.selkentfastenings.com/image/width/350/height/350/filename/WebCat-000a000500040017.jpg
@@Willy_Tepes you will be the first one to try them, Other issue is that quad-copter motor needs very high RPM I am not sure this will suffice based on your propeller configuration and other requirements. It is more complicated than simple yes or no.
@@netmedias7657 Thank you for the answer. It is actually a monocopter I am building but that would just confuse the question. RPM was my main concern. How fast does it go and could you make it go faster? I am not limited in any way with my design. It is just logical to start with the motor-propellor size. I might as well go big and these can be had for cheap.
Hello and thank you for the video. I have a 24 volt 200 watt booster motor with just yellow green and blue wires, what controller do I need to run it on my bike? I saw one with a throttle handle but also has other connectors, not sure if it would work... Any suggestions? Thanks.
@@netmedias7657 thank you. interesting, i thought 5k would be the right one... I used 20k and acceleration happened only at one quarter of the rotation..
Hi, I tried using the same BLDC controller with the same wiring. When I input 27v battery (2A), things heat up a little bit within 1 minute, and one capacitor exploded. the controller should be able to handle max 36v. You mentioned the controller fired when you use original battery from the hover board. If I use lower voltage, the wheel won't spin. Do you know any controller can handle 27v input power? The capacitor that exploded rated 16v, next to the Set wiring.
Holly Hertig It works with 36v but voltage regulator gets very hot. Make sure you use a heat sink. If your thinking about using it with hoverboard like setup then don't use it. It does not have any breaking use a $33 hoverboard kit. You can also add led and BLE sound to it. Good Luck. www.ebay.com/itm/Scooter-Main-Circuit-Board-Motherboard-Replacement-Parts-For-Balance-Scooter-US/264087485966?hash=item3d7cd73e0e:g:gYsAAOSw3S5b6iPc:rk:18:pf:0&LH_BIN=1
Netmedias I have this same question. I’m a dwarf. I’m 3ft and 55 lbs. I want to build a small powered wheelchair that I doesnt weight 120 lbs. I want to use these BLDC motors and a 36v Lipo for light weight. I had someone suggest using a modded hoverboard motherboard. What would you suggest? What about a sabertooth? Any benefit for one over the other? Besides price? Thanks for any input!
Wonderful video, gonna go watch Part 2 now... Question: My hoverboard motors had one more wire coming out of it - a white one... Is that anything you've seen before? It *might* be power for the LEDs in the hub - I will check that out too...
I want to run two motors with two boards, but I want them to turn equally fast. I want to use the signal (out) pin on the board. Can you help me with my question?@@netmedias7657
Hi! very interesting and educational video....i have a question on how and what kind of motor controller that accept high voltage dc input, like for example 250v dc to 300v dc? Please share it here....thanks a alot
I follow your instructions just fine, but I question your choice of terminology. The "POD" as you call it, is referred to as a "POT" to the rest of the electronics community. POT being the short term for POTENTIOMETER unless I'm missing something brought out in a previous video. BTW these home automation videos of yours, are the best on UA-cam for this subject. Good job!
Sorry for miss pronunciation. I know that, but I always miss speak it. Some people also call them variable resistor in some part of the world. Thank you for the correction.
This controller seems to have a power ramp up feature. I am trying to build a balancing robot and this is causing a problem. Do you have a recommendation?
Can this chip esc spinn the motor when is totentiometer meabe set on 50percent and than I puge the batery? Go spinn motor.? I nead this know.. to me prijekt
Can I use the original hoverboard battery if I want to build a e scooter? Everybody else Who build a scooter used the original Hoverboard battery. And why does it fry if i use it. Please answere Luke
I bought one of these controllers. I think I fried it using the the hover board battery. What is the maximum size battery I can use with this control unit. I was also wondering if I can use a 19 V DC power supply with it instead of the battery. I’m looking to make a large rock Tumblr with it and I need constant power for weeks. Please let me know your thoughts on this. I would really appreciate it. Thank you very much.
I have thé same problem did it work with the 19vDC
Is the variable speed adjustment same as a twist throttle or in that manner similar where it wouldn't matter if you had one or the other hooked up
I have the same controller but I am trying to develop braking when changing direction, since the code waits for it to finish turning to change direction.
Excellent! Would it go fast enough to cut wood (cnc router)?
5:25 La placa trae dos reguladores uno 317 y el otro 7805, ninguno de los dos soportan mas de 36v en sus entradas de tension, por lo que vi en los datasheets los transistores si son hasta 70v, creen que cambiando la resistencia 1000 SMD que alimenta los reguladores podre poner una bateria de 42v comunes en patinetes y hover board?
To slow the motor use dynamic breaking. Power to zero. Short 2 of the 3 wires together and it will come to a stop, the motor will induce current in the coils, causes dynamic breaking. But it takes motion to do this. So the effect stops when the motor does
Okey gracias
Thanks for this! I'm about to try it with the 36V hoverboard lipo. Can you explain why it fried your board? They should be able to take 36V? They say to add heatsinks to the MOSFETs over 60W, did you try that? I'm trying a similar "DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board LJ" $10 board.
Also did you see this? He figured out braking with this board ua-cam.com/video/sUEJWnqO27k/v-deo.html
First voltage regulator gets extremely hot when used with 36 volts battery. Second my board's etching was burned.
Thanks, you're right. AccuXperT said the 36V batteries run at 42V which burn out the board. I'll look for another battery, you saved me a board!
@@alana314 what battery did you end up using?
@@ManuelRoldanVega I ended up swapping controllers instead and used an odrive
You say that the battery of the hoverboard itself wil fry the board, but does that also apply if you're running 2 of the motors on only the battery from the hoverboard itself?
Hello, I'm Orlando Tristão, I'm from Portugal and I'm in a wheelchair. Congratulations on this video, no doubt many will benefit from your project. Please help me if you feel well. I need to adapt two Hoverboard motors, (36V 500W), to my wheelchair. I need to know which controller is ideal and how I can connect a joystick. Could you please help me? I await your dear reply. a hug, thank you very much
Sure, please email me.
आपकी..कीट..मारकेटमे..मिलसकतिहै..आपका..रेट...बतादे
Is there the same amount of volts at the output as at the input?
Did you test it with initial torque? I tested this controller and it have problems to start when wheel is under a load (initial torque). In your video all rotation tests is in "free wheel" condition so it starts smoothly. But when wheel is under the little load controller has problems to start (it just jumping back-forward). Just start rotation in slow rate and try stop it by hand, it has no torque-control loop.
Thanks! You have saved me from from frying some stuff
Thank you
Hi mate is posible to change the mosfet? To 36v 100A??@@netmedias7657
What’s the difference between the factory battery and the ones you had to use???
Is it possible to achieve forward and reverse rotation of the motor with one potentiometer?
Yes. 2 of the 3 wires need switched. Any 2. So you would need a switch. Position 1 for forward and position 2 for reverse
i've a simracing using this hover motor. cold i use the controller to make the forcefeedback? using a arduino pcb? or stm32?
I have a working hoverboard motor (tested on another system ) , I have purchased a brand new 36v controller with lcd ( s866 ) brand new throttle and brand new hoverboard battery for my e bike project but I'm experiencing no throttle issues I have checked voltage and purchased 3 brand new throttles checked wires tried swapping around but still no throttle
I thought he said he was going to do another video to follow through with this one? Can you please make that video :) Thumbs up if you want to see him wire this up with the uno and ESP3266!
hi, so if i had to power this with a power supply instead of a battery i need a 14,8 volt and 2,3 amps power supply it will work ? can someone please tell me if i am right ?
I don't normally comment but thanks.. best explained and actually can now test mine my LCD broken with throttle and trying to by passing it to a new throttle without lcd ..
Can I control two motors by one driver like this in a video?
whats the resistance of the POT? does it matter what size it is?
You said this board can not generate any breaking torque. How would you recommend slowing the wheel. I have that wheel and board and want to make an electric skateboard. Its all set up and works, but now i want to add breaking. Do i need a different board. If so, which one?
Holy crap! You killed it. I've been looking for a video like this for too long. Where was this 4 months ago?
Will it work without hall sensors?
I'm curious about the Hall Sensors, do they need to be connected?
It's not like a BLDC controller needs Hall sensors to run, they can easily run in sensor less mode. Hall sensors are more about information on the running motor such as direction and speed. Its possible to adjust a BLDC motor just using the phase wires and looking at current draw/feedback but there are numerous other variables both static and dynamic that increase complexity and ultimately limit effectiveness. Hall sensors can provide detailed position information which certainly improves the ability to tune a BLDC's performance, however there are many many different kinds of Hall Sensor based on measured parameters and abilities of detection. Hall sensors can just detect, or provide position, they act as momentary switches, or as latch switches.
I have ordered similar controller boards, but the documentation is utterly void of any specifics regarding the Hall Sensors... It makes some comment about motor being different, parents paying attention, and my drive plate will burn.... While its possible they are trying to say: If you drive your parents car faster than they do, they will burn your dinner and serve it to you on a plate, I suspect they intended something else. I believe this is a warning that when connecting call sensors you must be careful the connections don't overload (e.g.
Can this driver work with a quadrature encoded motors?
Hi I want to make an electric quad using 4 hoverboard motors , if I want to control all of them from a single pod, I need to buy more board and connect them to a single pod and use 4 batteries with them? Or I can use one board with 4 motors and a single battery?
Thanks in advance!
You will need 4 boards.
@@netmedias7657 and I can connect them to a single pod? And a single battery? Or I need 4 batteries?
@@sefuvostru1680 use 1 potenciometer and put the VR wire in the four boards
What pot size are you using please?
I need to have a pot that will allow me to have the wheels just turning at walking speed for my golf trolley conversion project.
I will be using two controllers with a double pole pot to try and get them balanced as much as possible.
For some reasons , I did everything that shown but nothing work.I thought had a bad board , change it twice and the third one still won't move the engine. Change the potentiometer , attached the VR to the 5volts connectors still nothing happened . I put the mother ack to the hoverboard ,all work fine . Anyone has any idea why s this happening ?
nice video, but I have a question my friend: is necessary connect the hall sensor? or Can I use without connect them? and also, I have a 24v DC motor brushless. but it have only 2 wires, red and black... Can I connect it motor 24 dc (2wires) in the board controller (3 phases) same as your video? I hope your reply. thanks!
This controller works with 3 phase motors only. You can buy a different version of this board that works without the hall sensors. You use Qunqi L298N Motor Drive Controller for 2 wire dc motor. Good luck.
I was using hoverboard's controller for tyres with a flysky i6 controller but now the issue I'm facing is board is not catching any signal from my transmitter can anyone guide me on this
Can we do a setup for a 52v 1500w bldc li-ion configuration?
I blew my controller and tried another still no throttle control i have potentiometer and Moffett z44-s please help i got my scooter scooter to run by the key and thats the only control I have on and off at a low speed, please help me figure this out. .
I have a 12v 0.18a 3wire blower dc blower fan, I want to slow the speed down for long periods but need the full speed for initial start up for a couple of minutes. Can you advise me on which type of small speed controller I should buy for the well being of my blower. Have seen vids on transistor/ potentiometer methods but would rather buy the right tool for the right job so to speak. Thankyou. Great video.
The colours on my hall senors are different, can I just do trial and error or will I cook the board??
dear l just bought bldc motor controller exactly same as you have but unfortunately it does not give output power. input is 20V battery. no output voltage. do you have any comments? thanks
can i use throttle instead of a pot?
I'm having very low torque at low speed, cannot find out why? Any thoughts? Thanks!
I have these pcb also but it is not working smoothly , some time goes forward or reverse ,
How to run motor without hall sensor because I have sensored board.
I wonder what the name of the module can be, the name, the number, the type or something, it is not enough to refer to the fact that it can be bought among the many 10,000 products.
Can I test brushless motors used for quadcopters with this? They don't have hall sensor, I have no idea what hall sensor is.
Can I use the 36v hoverboard battery for two boards tough?
Yes you can use 36v but make sure use heatsink not to burn the board
@@netmedias7657 Also can I use a custom heat sink that I'm going to make, so that I can screw it on to the mosfets.
Yes, you can
Hi, as per your advice connected two controllers on two motors & one throttle. But again I am stuck in middle because I have no Reverse option in controllers. Any advice to modify controllers Reverse function without swapping wires?
Appreciated.
Hello my friend! I can not find the white connector, you have on the board.
You have the link?
Thanks 👍
Why are you saying a 36v battery would fry the board? This is a 36v motor no?
I was wondering the same thing. I’m using mine to build a heavy duty rock tumbler so I don’t think I need as many volts. I’m not looking for speed. Looking for slow with a lot of torque. I’m hoping to run it on a 19 volt power supply. I tried to get the motor running using one of the other controller boards without the clip on wire leads on it. So I’m really hope this works as it’s getting expensive . I’m up over $35 on the 2 boards. Good luck with your build.
Is any module for bldc motor. About 30 ampere and 55 volt
If the application is simply speed and direction control, why you need an encoder?
Hi, nice informative videos.
Im planning to convert my hoverboard into gokart. Can you advise me if can connect both 350w motors parllel to one 350w controller.
2nd what gage wiring i should use.
3rd can the original battery of hoverboard be used.
Thanks in advance.
Hoverboard batteries are known to go kaboom, so i would buy a better one
You should be using 1 driver per motor unless the driver supports using multiple
As for guage, use the same as the motor
Also, it wouldn't be a fast gokart as hoverboard motors are slow
Hope that helps!
Can I connect this controller board to two segway motors
I'm trying to run six of these to an ardunio...is that even possible?...24 inputs needed Mega only does 16...so can I splice the hall sensor inputs?
Can all the fets be heat sinked together or will they short each other out?
what connectors did you use?
Can the bldc ex Hoverboard motor be used for a diy scooter without a hall sensor?
Hi! I just wanted to know, what do you call those white connectors you used instead of soldering it? Thank you😅
What's the name of the motor controller and switch ??
Hi..how about torque? same like nema 42? whats Nm torque??
Hello please show thre right way to put heat sink, can I put single common heat sink or need seperate heat sink for each six mosfet
no you cant put common heat sink!
you must make all mosfet separatly, or
use plastic isolator for screws or plastic screws and isolating layer between all of transistor and common heat sink (ex. kapton tape 2-3 layers).
also check heat dissipation for linear stabilisator, if you use 24V and higher for power supply.
@@igormorozov6801 hello thank-you for reply, i got good solution for common heat sink using mica sheet and plastic screw
@@ledshowinindia6571 also right choice :)
Insulating Washers is used in commercial driver for electric scooter and hoverboards.
www.selkentfastenings.com/image/width/350/height/350/filename/WebCat-000a000500040017.jpg
Would these motors work on a quadcopter?
no
@@netmedias7657 Any particular reason for that? "No" is not an answer.
@@Willy_Tepes you will be the first one to try them, Other issue is that quad-copter motor needs very high RPM I am not sure this will suffice based on your propeller configuration and other requirements. It is more complicated than simple yes or no.
@@netmedias7657 Thank you for the answer. It is actually a monocopter I am building but that would just confuse the question. RPM was my main concern. How fast does it go and could you make it go faster?
I am not limited in any way with my design. It is just logical to start with the motor-propellor size. I might as well go big and these can be had for cheap.
Hello and thank you for the video.
I have a 24 volt 200 watt booster motor with just yellow green and blue wires, what controller do I need to run it on my bike? I saw one with a throttle handle but also has other connectors, not sure if it would work... Any suggestions? Thanks.
Could you help me buy your parts? I want to get battery, BLDC in wheel motor that you use. I want to know the parts links.. plz
Same here
potential metrel ?
Plz tell i am run in ALTERNATOR MOTOR.
Great Video, where did you get the female wire adapter that the battery plugs into?
You can buy it on Amazon or Ali express.
This can brake and reverse?
No, it does not.
Good video my friend 👍🤗🥰
Can I use a 36 v controller like this one but power it with a 42 bolt battery ?
You will fry the controller if it is not rated for 42 volts. You can used dc to dc converter 42 to 36 dc. Search it on google.
@@netmedias7657 does the amp rating for the step down converter need to be 15 amps ? The same as the controller?
thank you indian man you really did me a favour
Hello, what Ohm potentiometer are you using?
500k
@@netmedias7657 thank you. interesting, i thought 5k would be the right one... I used 20k and acceleration happened only at one quarter of the rotation..
hey, great video. I have a BLD300B and a hoverboard wheel, how would I go about connecting it to my computer to send speed and direction to it?
Can I controll it with hall sensor throttle ?
Ey! when you turn on the system, does the wheel have the brake activated?
No brakes
i’m trying to control brushless motor with arduino. Is it possible to control brushless motor with arduino by using controller you used in this video?
YES. This controller is for 3 phase motors only.
is this suitable for sensorless bldc motor ,and how?
I have not tried it but I have seen some people are using them without sensors.
can you share the 2 motor controller specs and Datasheet
have you tried the open source vesc?
No, but will look into it if time permits.
If you do not put a heatsink on that controller you will fry it when it overheats!
Hi, I tried using the same BLDC controller with the same wiring. When I input 27v battery (2A), things heat up a little bit within 1 minute, and one capacitor exploded. the controller should be able to handle max 36v. You mentioned the controller fired when you use original battery from the hover board. If I use lower voltage, the wheel won't spin. Do you know any controller can handle 27v input power? The capacitor that exploded rated 16v, next to the Set wiring.
It will work with 36 volts given that you use heat sink. I was using it without heat sink.
Is it possible to connect the controller to arduino/stm32?
Are these motor suppose to vibrate when they run?
No
Hello! Will you be making a tutorial for the board shown at the end of the video? Thank you!
Looking forward for a video on odrive controller too.
Is there a way that you can still use the 36v? I want to control 2 wheels, some 12v RGB lights, AND SOME speakers so it can talk and play music too.
Holly Hertig It works with 36v but voltage regulator gets very hot. Make sure you use a heat sink. If your thinking about using it with hoverboard like setup then don't use it. It does not have any breaking use a $33 hoverboard kit. You can also add led and BLE sound to it. Good Luck.
www.ebay.com/itm/Scooter-Main-Circuit-Board-Motherboard-Replacement-Parts-For-Balance-Scooter-US/264087485966?hash=item3d7cd73e0e:g:gYsAAOSw3S5b6iPc:rk:18:pf:0&LH_BIN=1
Netmedias I have this same question. I’m a dwarf. I’m 3ft and 55 lbs. I want to build a small powered wheelchair that I doesnt weight 120 lbs. I want to use these BLDC motors and a 36v Lipo for light weight. I had someone suggest using a modded hoverboard motherboard. What would you suggest? What about a sabertooth? Any benefit for one over the other? Besides price? Thanks for any input!
Any way to add RC receiver to that board
Hi. I am in SA. South African. Where can I purchase controllers. Do you have a supplier.
Question what’s the EL and Signal wires for?
EL enable start/stop control (terminal connected to 5V start or grounding the motor stops)
Signal is for sensing hall encoder.
Wonderful video, gonna go watch Part 2 now...
Question: My hoverboard motors had one more wire coming out of it - a white one... Is that anything you've seen before? It *might* be power for the LEDs in the hub - I will check that out too...
Hi its for a temp sensor
I would like to control the controller and motor with a micro:bit. It uses am pwm signal. Is it posible to connect it instead of the potmeter?
It will work with any MCU with 5v GPIO. I had some issues using it with ModeMcu without using a level shifter.
I want to run two motors with two boards, but I want them to turn equally fast. I want to use the signal (out) pin on the board. Can you help me with my question?@@netmedias7657
ua-cam.com/video/QrH8NNfC-UE/v-deo.html
Hello, which kind of charger should i use to charge the battery shown in the video please?
Have you ever figured this out. I'm wondering the same thing
How to fix e bike throttle to this board
Boas tardes amigo será que se pode fazer isso com a centralina da trotineta elétrica de 36v
Hi do u know how many km/hr can this board support?
about 17 km/h
Do i need to use the hall senser if I just want to have the wheel move forward with the potentiometer
It depends on the type of controller. You can get a controller without the hall sensor and it should work.
Hi! very interesting and educational video....i have a question on how and what kind of motor controller that accept high voltage dc input, like for example 250v dc to 300v dc? Please share it here....thanks a alot
You can use relay with MCU if you want to turn motor on and off.
I follow your instructions just fine, but I question your choice of terminology. The "POD" as you call it, is referred to as a "POT" to the rest of the electronics community. POT being the short term for POTENTIOMETER unless I'm missing something brought out in a previous video. BTW these home automation videos of yours, are the best on UA-cam for this subject. Good job!
Sorry for miss pronunciation. I know that, but I always miss speak it.
Some people also call them variable resistor in some part of the world.
Thank you for the correction.
Hi, you didnt post new video with that black board... any tips for the link to buy that board?
Thanks for sharing video, I was looking for another controller like this more powerful but didnt find it
This controller seems to have a power ramp up feature. I am trying to build a balancing robot and this is causing a problem. Do you have a recommendation?
Hi, i am building the same type of robot, did you ever find a way to fix this or a different controller?
Hi, Can we use this controller with 24 V smps power..?
Yes
thank you for the information, i learn something
Glad to hear it
how much the controller for 3 hover motor
Please check on ebay
Can this chip esc spinn the motor when is totentiometer meabe set on 50percent and than I puge the batery? Go spinn motor.? I nead this know.. to me prijekt
Can I use the original hoverboard battery if I want to build a e scooter? Everybody else Who build a scooter used the original Hoverboard battery. And why does it fry if i use it. Please answere
Luke
I am not sure. You can try it but voltage regulator gets very hot when used with hover board battery. It is a fire hazard. Good luck.
Thank you I will try it and I will screw it on an aluminium plate to keep it cool👍
@@moonlightdanc84 you can do it? Im looking for someone that uses this board and the hoverboard battery (sorry for responding 2 years later lmao)