Installed wheels. Carries them lol great job. Honestly? I'd install more uprights. Any gap could be a mishap. Even bidirectional. It simply means they can not collapse.
Автор молодец. Самый удачный деревянный вариант из всех просмотренных. Расейские вообще какая-то муть. Сделал по указанным размерам, доски взял толщиной 25 мм и шириной 100 и 150 мм, общая ширина 250 мм, вполне достаточно, количество промежуточных опор из доски 50х100 мм увеличил вверху до 5-и, внизу до 6-и, и ещё две опоры под наклонной доской в промежутках. Размеры определены идеально, угол наклона доски позволяет заезжать и съезжать без касания о неё передним бампером даже Матизу 0.8. А у него очень маленькие колёса. Общая высота эстакады 270 мм, вполне себе приемлемо, под машиной можно свободно работать. Дёшево и сердито.
It shouldn't rack with the triangulation, IF he screwed the acute angle together at the ramp entrance, which I didn't see him do, but maybe I missed it.
ramp design allows for tools and parts shelves, very handy, 1:58 Mursement one: 230mm, 2:12 Mursement Tow: 480mm, 2:20 Mursement Three: 900mm, 4:24 You should drill 4 hole for 4 screw for each lumber, i did it later when i install the lumbers. And if your wood is impregnated maby you do not need drill holes at all. As i did not drill hole for the 2 other screws on the lumber. The bolt goes through without cracking the wood.
Kann man die auch auf eine Höhe von 450mm bauen? Wäre angenehmer unterm Auto zu arbeiten. Und wie sieht es aus das man hinten auch noch mit hoch kommt?
I would like to build a wooden ramp in the shape of a right-angled triangle with horizontal slats, it will be placed between the two iron ramps in the event that the car ends up in the empty space between them, which is 57 centimeters away.It's improbable the car could drive over the empty space, but when I get off I always fear that it could happen. I was wondering how I can tell if the wooden ramp will be suitable for cars.
Nothing at all wrong with those plus you get to use them as a bench well done! 👍 A slight improvement would be to use threaded bar instead of screws if you have some.
В России за 70$ сделают из металла😅. А так не плохо, своими руками. Если бы ещё выложили схему с размерами, то было бы ещё лучше. И нужно обязательно покрасить или покрыть лаком.
This looks a little flimsy unless the car is very lightweight. Most designs I’ve seen use stacked, treated wood so that it’s very strong even if it is a bit heavy.
Cheap vs less expensive. Cheap describes the low quality of ramps you buy at a store. Less expensive describes the higher quality of ramps you build yourself. You've built ramps that are better quality (sronger) than any you could buy.
This is something I can build,my dilemma is,for $70 I can buy metal ramps and avoid the labor of building these heavy ramps.The prices of everything now days including lumber makes these practical projects,impractical.I had build my wooden ramps as a teenager to service my 68 GTO in 1968,I wish I had them now.
$70 en internet hay unas de caucho resistente que valen $30, si las hiciera con madera reciclada seria diferente pero comprar madera y gastar tanto no tien sentido cuando puedes comprar unas por menos dinero
Installed wheels. Carries them lol great job. Honestly? I'd install more uprights. Any gap could be a mishap. Even bidirectional. It simply means they can not collapse.
I've made a pair of my own. They work better than expected. Serviced easily two of my cars this summer. Thumbs up for the idea.
Remember when wood was affordable? Nice ramps though 👍🙈🤣
Exactamente la madera tienen un precio muy alto, prefiero subir y bajarlo y ponerlo en burro
Хочешь отвезти девушку в дорогое место? Своди её на лесопилку))
Anyone help me out? I was thinking of extending this to fit the entire car but i feel like that's too heavy
These are nice car ramps! I really like the slope and the design; they look strong and well-built. Great for working on your car!
So far it's the best wood design.!
Скаты надо делать съёмными удобней работать, а так все СУПЕР
Awesome ramp! And the best part was using the ramp as a coffee bench. 😊
Thanks for sharing.
good work…
enjoy your cookie and coffee 👍🏻
Thanks body 😂😂👍
Looks like a house of cards. Hopefully there’s enough material there if it were to collapse to keep the vehicle from coming all the way down on you.
I was thinking same thing. If nothing else at least some 2x4's down the middle to provide longitude support.
Автор молодец. Самый удачный деревянный вариант из всех просмотренных. Расейские вообще какая-то муть. Сделал по указанным размерам, доски взял толщиной 25 мм и шириной 100 и 150 мм, общая ширина 250 мм, вполне достаточно, количество промежуточных опор из доски 50х100 мм увеличил вверху до 5-и, внизу до 6-и, и ещё две опоры под наклонной доской в промежутках. Размеры определены идеально, угол наклона доски позволяет заезжать и съезжать без касания о неё передним бампером даже Матизу 0.8. А у него очень маленькие колёса. Общая высота эстакады 270 мм, вполне себе приемлемо, под машиной можно свободно работать. Дёшево и сердито.
Ещё можно в гараже подвесить и использовать как полки)
Скажите есть размеры данной эстакады.
Thank you so much Jim:) Glad you liked it.😀👌
Nice video. But I will stack my boards since I will be using them long term and on semi trucks! I like your wheels and storing them as a bench.
Might want to substitute 4x4s instead of the 2x4s less likely to rack on you.
It shouldn't rack with the triangulation, IF he screwed the acute angle together at the ramp entrance, which I didn't see him do, but maybe I missed it.
You must be an engineer. I’ll stick with what I originally said.@@allegory7638
Your ramp design allows for tools and parts shelves, very handy, I like it!👍
oh wow look at the room under that's awesome! great job
La idea es buena pero por seguridad deberías poner más blokes en el soporte
Loved your work, may I know the entire length of the ramp total height of the ramp the length of the slope
Absolutely the best I ever seen. I build it and I am very satisfied 😌 😀👌👌👌👌👌👌👌
Two fold Love the bench
Thanks for sharing
If you put two more castors on the end you could stand them upright and push them in a corner.
Just what I was looking for, well done.
You have some real good skills! pleasure seeing you in this!
ramp design allows for tools and parts shelves, very handy,
1:58
Mursement one: 230mm,
2:12
Mursement Tow: 480mm,
2:20
Mursement Three: 900mm,
4:24
You should drill 4 hole for 4 screw for each lumber, i did it later when i install the lumbers.
And if your wood is impregnated maby you do not need drill holes at all.
As i did not drill hole for the 2 other screws on the lumber. The bolt goes through without cracking the wood.
Kann man die auch auf eine Höhe von 450mm bauen? Wäre angenehmer unterm Auto zu arbeiten. Und wie sieht es aus das man hinten auch noch mit hoch kommt?
Excellent work thanks 👍👍👍👍👍
I would like to build a wooden ramp in the shape of a right-angled triangle with horizontal slats, it will be placed between the two iron ramps in the event that the car ends up in the empty space between them, which is 57 centimeters away.It's improbable the car could drive over the empty space, but when I get off I always fear that it could happen.
I was wondering how I can tell if the wooden ramp will be suitable for cars.
Stack the wood in layers like paper and they will not fail.
A good invention !!!
Like #11 👍👌
Thanhks
This is awesome dye Thanks
I build it and its work perefectly for my SUV👌👍👌
Quelle sont les dimensions des rampes ? Hauteur et longueur des rampe svp, quelle bois utiliser vous ?
Nothing at all wrong with those plus you get to use them as a bench well done! 👍
A slight improvement would be to use threaded bar instead of screws if you have some.
Thank you bro
В России за 70$ сделают из металла😅. А так не плохо, своими руками. Если бы ещё выложили схему с размерами, то было бы ещё лучше. И нужно обязательно покрасить или покрыть лаком.
If he can build these ramps he needs to build a workbench! Get the heck up off the ground. Nice ramps, btw.
good stuff
Can someone post the numbers in inches plz ..?
M-ai inspirat și pe mine :D
enjoyed watching (A+)
This looks a little flimsy unless the car is very lightweight. Most designs I’ve seen use stacked, treated wood so that it’s very strong even if it is a bit heavy.
Good job thanks made one
Hi what degree of angle did you use?
14 degree. Better watch my other drawing video for more detail. At 0:29 here ua-cam.com/video/kmy_dOAA_1Q/v-deo.html&ab_channel=ThinkTechnikk
Excelente ideia ...parabéns 👏👏👏
Hi. How much would the wood cost today if bought from home depot?
Different location different price ,
Hi, great video, what is the thickness and width of the wood u used ? :)
See picture 0:41 , here are all you need
@@ThinkTechnikk Oh thank you, I probably watched whole video and skipped that part :D
Now the only thing I’m missing is a driveway.
Add some skateboard grip tape on top.
Will it work fine with front wheel drive?
I'm afraid it could launch back if it slips.
Btw, that's really expensive.
absolutely
In the UK that timber would cost half as much as the car!
Jest super
Good
Cheap vs less expensive. Cheap describes the low quality of ramps you buy at a store. Less expensive describes the higher quality of ramps you build yourself. You've built ramps that are better quality (sronger) than any you could buy.
Can passibly Paint the woods rampete u build?
Yes of course, the wood is paintable, but this wood is impregnated which means is waterproof and tolerate a lot of weight 👌 its up to you than
Buna seara!
Ce dimensiune ai folosit la burghiu?
Mulțumesc!
Please see 0:43
This is something I can build,my dilemma is,for $70 I can buy metal ramps and avoid the labor of building these heavy ramps.The prices of everything now days including lumber makes these practical projects,impractical.I had build my wooden ramps as a teenager to service my 68 GTO in 1968,I wish I had them now.
These are taller and more stable
I wouldn’t trust my life to $70.00 ramps. Not a chance.
Nice Tesla pants! 🙂
Молодец !
👍👍👍👍👍👍👍👍👍
$70 en internet hay unas de caucho resistente que valen $30, si las hiciera con madera reciclada seria diferente pero comprar madera y gastar tanto no tien sentido cuando puedes comprar unas por menos dinero
100%👍👍👍👍👍
바로 이거야~~^^
This time I will do it manually with the help of Stodoys plans designs.
Perfeito.
😀👌👌👌
Just remember, not certified so if it fails and someone gets hurt, YOU go to jail
Just remember, anyone can sign a waiver ........... Use at your own risk.......
@@rh7163 waivers don’t stand up in court, you should know that. Manslaughter overrides a waiver every day of the week.
What country are you guys from where un-certified wood ramps can lead you to jail?
What a stupid statement……if it fails, he dies, he will be dead!
crappy music
786
not for serious jobs