Відео

Hi did you have any problem with it since you upload video ? I buy my kona ev 2021 last week and i want try it if it's safe .

This looks a little flimsy unless the car is very lightweight. Most designs I’ve seen use stacked, treated wood so that it’s very strong even if it is a bit heavy.

Finally someone posted in mm and not this other "obsolete" measurement! 😅

this seems like a bad idea. You'll cause uneven wear and you'll fell vibration upon braking. Just buy a set of rotors. they're cheap.

Super labombastic fantastic skolastic 🙏🧠🦵👑👂💕🦷✈😇👀😍😘🤝🛳🥰😌🤼‍♂💑👃🥿⛑️💪🧛‍♀️🥽🚐♂️👽🚦🚀👌👏🤘🌛☀🐬👍💘💋💯

Super labombastic fantastic skolastic 🦷✈🧠👂🙏😇👀😍😘🤝👑🛳🥰😌🤼‍♂🧛‍♀️💑🦵👃🥿⛑️💪💕🥽🚐♂️👽🚦🚀👌👍👏🤘🌛☀🐬💘💋💯

Can someone post the numbers in inches plz ..?

Thank you!

Bar far the most useless content on youtube

Buy a Mercedes

Wtf is wrong with u

Not a good idea! The dust will get into other parts of the car.

Cheap vs less expensive. Cheap describes the low quality of ramps you buy at a store. Less expensive describes the higher quality of ramps you build yourself. You've built ramps that are better quality (sronger) than any you could buy.

In the UK that timber would cost half as much as the car!

$70 en internet hay unas de caucho resistente que valen $30, si las hiciera con madera reciclada seria diferente pero comprar madera y gastar tanto no tien sentido cuando puedes comprar unas por menos dinero

PDF plans please

Instructions not clear. Tried to brake and rotors were only 2mm

When you fit new brake pads but haven’t driven the car for 2 years

These are nice car ramps! I really like the slope and the design; they look strong and well-built. Great for working on your car!

Pls dont do this, thanks me later

100%👍👍👍👍👍

Angle grinder vs grind stone? Bro the cutting disc will end up on your face.

La idea es buena pero por seguridad deberías poner más blokes en el soporte

hi fbi agent

Never hang a caliper by the brake hoses, and force in a brake piston that way with stilsons or similar, you will cut into the protective rubber ,

Hello from Canada . I own the exact same shifter on my 2007 legend and all the bolts unscrew but just keep turning and I have no access to go behind . Question do you know if I have the rubber gromets also and should I force slowly with a crowbar like you did . Note I have carpeted wall. Also the reason I want to remove it is only to remove the handle to replace the shifter spring so it locks into neutral and do you know the spring part number Thank you. Great video Regards David

Hi! Very good idea. Do you just put it in or do you have to fix it with screws?

My new car has rusty disc brakes....is that common?

Fail

Loved your work, may I know the entire length of the ramp total height of the ramp the length of the slope

Just curious if you did this long term? No problems?

Sandstone?

I think the fumes got to this dude. smh

This must be a Car Salesman trying to make the car look more appealing for a few days to make it easier to sell.

Yes, definitely do that or your breaks won’t work.

Metal?

With them gloves on and they catch the moving rotors your asking for a nasty accident

Kann man die auch auf eine Höhe von 450mm bauen? Wäre angenehmer unterm Auto zu arbeiten. Und wie sieht es aus das man hinten auch noch mit hoch kommt?

a week later its back ,,,

and you just made it thinner... what's the point?

I clicked on the link but it just takes me to a jpeg picture of the table. Do you have a link to the pdf plan?

"Thanks for the fantastic video! Could you please write down the part number of this controller? Thanks again."

Thanks for the video. I sure wish you had disassembled it and put it back together. I have taken mine apart and it looks just like yours. For the life of me I can't figure out where the brass bushing and the funny shaped plastic plate with three holes in it goes. The rest I have figured out. Some parts just fell out when I removed the back plate. Hope you are still checking this video for comments and you can help me out.

786

I have similar problem, problem is still there even after changing the coil

Just remember, not certified so if it fails and someone gets hurt, YOU go to jail

People says that engines heat can damage the foum frunk. İs this poseble or not?? When I need extra space I want to use like this.

Great Job and very intelligent. İ will try this.

great video thanks you for making it, my car only does about 2,000 miles a year, so will save me money doing this

This glue sticks to kids