Thanks for this detailed video !! Thanks to you I managed to solve my problem. I had bought the original spare part, but there was still water leaking. Thanks to you, I could see that the original part does not come with the o-rings ... I had to re-use the ones from the faulty part, but hopefully the problem did not come from them. Keep up the great work !!
Hi thanks for your videos!! Following your video and instructions I still have an issue with a steam leak from inside the machine? The main steam tube is ok? I dont know why it happen?
@@yt.myworks The steam leak comes from the center of the module…I will check all the main tubes,but I might did something wrong when I putted everything together
Witam, aby zmienić ilość kawy należy zadbać o to aby tłok zaparzacza dało się łatwo poruszać. Następnie trzeba zrobić więcej jak pięć kaw bez ziaren, ignorując komunikat "brak ziaren". Wtedy maszyna powinna przestawić na dłuższy czas mielenia samoczynnie. Jeżeli chodzi o wodę pod zbiornikiem na fusy to musisz najpierw zlokalizować wyciek, wtedy mogę udzielić dalszych wskazówek. Pozdrawiam
Witam, mam problem w tym modelu ze cala woda leci do tacki po lewej stronie zamiast dyszami, zasylikonowalem łączenie ale nic nie dalo, sprawdzilem zaparzacz i termoblok, co moze byc przyczyna? Ekspres ma 5 lat, wymienic termoblok? Dodam ze na spieniaczu woda dziala ale tez troche cieknie
I have some coffee grounds in the large tube that goes from infuser to heat expansion chamber. Is that a problem? Everything else looks fine. Pucks don't stay together but are not too wet.
Auch ein exelentes Video. Das umfangreiche reinigen habe ich mir damals bei meiner Cappucino auch nicht angetan. Lieber auch einen neuen bei BND Kaffeestudio gekauft
Please I really need some help : I have a Delonghi Primadonna Deluxe S which doesnt want to froth the milk when using the carafe. So have found a few video showing the specific faulty solenoid valve responsible for that OR the milk frothing coupling/coupler assembly. Have just replaced both and still coming out just steam. What could be ??? Thanks
Hi, before you replace any other parts, try to completely disassemble and clean the milk carafe. Make sure that all the screws in the cover are removed, then you can disassemble everything and clean it thoroughly. For this I recommend a milk cleaner like this one, it's cheap and available in any drugstore: amzn.to/4gRqDC6
@ Honestly I did it a few time ,took the screew out and give a proper cleaning(i dont think the carafe will be faulty) Have replaced since I asked the question,the top solenoid valve ,and I have realised it does have one more under the front cover… Any other clues what might be the issue? The steam is coming strong when trying to froth the milk but is not sucking any milk from container.
The milk foam is created in the milk container, not inside the machine itself. It is important that the steam pressure is strong enough to draw the milk. Additionally, the water pump must be functioning properly to generate sufficient pressure. I also recommend trying a different carafe, as it may happen that these no longer work properly after a certain time.
@ possible the water pump to work fine for coffee or anything else but not for the milk frothing? Manufacture year on the pump is 2011 ,so might be too week?
This is been extremely helpful, thank you. I have a ECAM 23.220 B-NN1, Looking to buy the new replacement mechanical valve , I am finding a lot of part numbers that all look the same summer called ‘infuser piston’ etc. I haven’t purchased an O-ring kit to rebuild my infuser piston. But unfortunately, I broke the small flange that holds the output silicone hose I have only one question. I found a small 1cm round wire that looks like a miniature key ring. It came from somewhere on the left-hand side when removing the screws to get to the mechanical valve. Unfortunately, I can’t add a picture here. But perhaps you know what it is? Thanks again for your brilliant service !
Do you mean the ring spring that is stuck on the steam lever? www.juraprofi.de/DeLonghi-Ersatzteile/Gehaeuseteile/DeLonghi-Dampfregelknopf-ECAM::9817.html
Thanks very much for this video. My machine is now working again. I do have a question though. How do I release the electrical cable to detach the front screen at 1.54 in the video? I've watched it several times and tried to release it on my machine but can't seem to find a way?
@@yt.myworks I replaced the full part and ran it with the top off to see why it wasn't working and the water was going into the part but just spraying straight back out. No water was taken in and distributed to any part. Steam wand and coffee didn't work at all.
Thank you for your efforts brother, I have changed the piston infuser with new one, but the problem got worse 😢 and the coffee collector drawer is now full with water compared to small amount of water 😢. What could be wrong?
It won't be the piston infuser, as long as you have connected everything correctly. Did you put o-rings on the hose ends? You have to watch where the water comes from.
Dzien dobry. Mruga mi ciagle lampka poziomu wody. Po kazdym plukaniu i zrobieniu kawy to sie pojawia. Trzeba przekrecic pokretlo spieniacza tam i z powrotem aby zgaslo. Co moze byc przyczyną? Dzieki z gory za odpowiedz. DeLonghi Esam magnifica 3000b
Witam, to oznacza że do układu wody dostaje się gdzieś powietrze. Sprawdź najpierw uszczelkę zbiornika wody w miejscu połączenia z obudową maszyny. Zbiornik musi dokładnie dolegać do obudowy. Usuń ewentualne zanieczyszczenia, często zbiera się w tym osad z wody.
@@yt.myworks wlalem do zbiornika ocet z ciepłą wodą wczoraj i zostawilem na chwile. Przeczyscilem octem miejsce gdzie jest czujnik wody i obudowe kolo zbiornika. Właczam, plukam ikonka sie juz nie zaswiecila🤝baja
Ich habe mein Gerät erst seit 3 Wochen. Auf einmal tröpt das Wasser nur noch plus ich habe Wasser im Auffangbehälter. Ich habe weiches Wasser 7,6 dH und ich benutze ein Filter. Ist wahtscheinlich wie hier an der gleichen Stelle defekt. Ich mach mir die Arbeit aber nicht. Auch, wenn hier alles 1A erklärt wurde, das sollte nicht so schnell passieren. Sehr ausführliches Video, Danke.
Dziękuję bardzo za super film😊. Przy okazji zapytam, jaka jest średnica oringów do wężyków teflonowych od podawania wody pod ciśnieniem które smarujesz? Pytam bo różnie podają 3,85x2x7,85 lub 4x2x8?
Good morning, My Jura 6Z is not working is having exactly the same problem that you described in the video " Jura Machine Doesn't Make Coffee - Water/Coffee Runs Directly Into the Drip Tray" , however the pin from the stepper motor of drainage valve is completely out, Does it have to be out or in with the power off? in your video it is in. Do you think this motor is jammed? how can it test it? Thank you for your help😀
Hi, when the machine is switched off, the valve is pushed out by the steel spring. In this state, the valve is closed. When the machine opens the valve, a loud clicking sound can be heard. Very often, the seals in the valve are worn out and the coffee flows into the drip tray. You can replace the gaskets or the entire valve with a new one.
Thanks for the quick reply, is there any chance for me to send you some pictures? The pin I am taking about is not the one in the valve, is the little stepper motor shaft, the one that press the valve pin. In your video when you remove the brewer unit I can see that the motor shaft is in not out. In my case it is out with the machine disconnected. When the motor shaft is out then it press the valve pin and hot water goes to the drain when it is in then the valve pin is depress, it opens the valve and the hot water goes to the brewer unit, is this right?? 🤔🤔Thank you.🙏
Witaj. Mój ekspres DeLonghi Magnifica S robi kawę lecz jest bardzo słaba nawet przy ustawieniu mocy na max. Wody leje tyle ile powinien nie ma wycieku do tacki z fusami jak na filmie. Czy przyczyną bedzie infuzor? Czy może być duża uszczelka na tłoku? Ewentualnie czy te infuzory co są na aukcjach do magnifica s pasują do wszystkich niezaleznie od modelu Ecam? Dzieki za odpowiedź pozdrawiam.😊
Witam, przypuszczam że przyczyną problemu będzie za krótkie mielenie ziaren które powinno trwać około 6-7 sekund. Polecam wykonanie czynności z mojego innego filmu: ua-cam.com/video/OJWguSgyf4c/v-deo.htmlsi=8bJ8E-Ovn1ob9pCU. Rzecz w tym aby zaparzacz i cała reszta dały się łatwo poruszać bo w innym przypadku ekspres redukuje ilość mielonej kawy. Uważaj aby starannie złożyć zaparzacz to jest bardzo ważne: ua-cam.com/users/shortsmOxrMerZSFo?si=WGvZDaVGl9IUiG__ Dalsze wskazówki później. Pozdrawiam
@@yt.myworks Dzięki za odpowiedź. Co do zbyt krótkiego mielenia, krążki z kawą wyglądają ok, gdyby było za krótkie powinny być mniejsze? A i zapomniałem dodać że próbowałem robić kawę na dwóch różnych zaparzaczach i taki sam efekt.
W moim Delonghi Dinamica właśnie pojawiła się woda w pojemniku na fusy i mniejsze kawy były zaparzane. Poczytałem trochę i zauważyłem, że po wyjęciu zaparzacza w infuzorze jest woda. Sitko w zaparzaczu jest czyste. Ekspres na gwarancji. Półtorej roku nic się nie działo.
Nie może być wody w infuzorze (przezroczysta część). To oznacza że pojawiła się nieszczelność. Po półtorej roku nie powinna pojawić się taka usterka chyba że ekspres używany był bardzo intensywnie np. 10 Tyś. kaw.
Hello, thank you very much for your video. I replaced a new brewing piston followed your video. Unfortunately there are still a few water drops in the ground collecting container after making coffee. Can you please advise if this is normal.
Witaj. Nasz automatyczny ekspres kawowy Jura S8 będzie wymagał konserwacji. Czy podejmujesz się również takich zleceń? Jak mógłby się z Tobą skontaktować?
I'm interested why you bought a new brew unit and didn't service it like you've done in the past. What were the problems that made you buy a new unit? Thanks for your great videos.
The Delonghi 370.95 has an almost identical structure, only the housing and the control panel are different. You can see how to remove the case in my other video: ua-cam.com/video/4iV0qUWUKAY/v-deo.html
Hey great video, I followed it all but decided to try fixing my current piston instead (following your other video) but now that I’ve put everything back together the machine does nothing, it just flashes the red triangle when I turn it on and nothing else. I checked the diffuser already like it says in the manual but it didn’t help. Any ideas what the problem could be?
Good video, except that i must have broken the connector to the motherboard as this cannot be fitted back. Just falls off. Pity no attention was aimed at that. All i can see in the video is that it's pulled off
Can you please advise if o-rings are already in the new brew unit. I didn't have them and the old ones didn't come out with the three plastic lines that attach with clips, so was presuming they were already in place?
Hello there. My maschine acts Weird. It gives some wet pucks, not super wet, but definitely wet. When I then try to descale the machine, most of the water runs out on the table ;( do you think it’s this part that are defect? Will I be able to see where it leaks, if I remove covers on the unit and try to run a descale? Of course I’ll be aware of electric shock.
Hello, you describe several problems that may have different causes. The wet puck indicates worn millstones or incorrectly adjusted grinder. Calcified heating casing can be responsible for water loss. And if the machine is more than four years old, then I generally recommend replacing the brew piston.
@@yt.myworksmaybe its calsified beating casing, where is that located? I havent touched the grinder. Its from december 2021. But we have very hard water with alot og calcium in it.
Thanks for this detailed video !! Thanks to you I managed to solve my problem.
I had bought the original spare part, but there was still water leaking. Thanks to you, I could see that the original part does not come with the o-rings ... I had to re-use the ones from the faulty part, but hopefully the problem did not come from them.
Keep up the great work !!
Excellent instructions. Glad I watched the whole thing before ordering parts. Would have forgotten the o rings.
Buen día. Gran trabajo y muy informativo para quienes nos dedicamos a esto. Saludos de México.
Hi thanks for your videos!!
Following your video and instructions I still have an issue with a steam leak from inside the machine? The main steam tube is ok? I dont know why it happen?
Hi, where does the steam come from? Check all Teflon tubes for calcification or blockage.
@@yt.myworks The steam leak comes from the center of the module…I will check all the main tubes,but I might did something wrong when I putted everything together
Check everything again.
Best master ever! 👍👍👍
Danke für das detaillierte Video!
Ja mam problem z iloscia zmielonej kawy oraz wodą ktora jest pod zbiornikiem na fusy. W infuzorze wymienialem oringi. Jakies porady?
Witam, aby zmienić ilość kawy należy zadbać o to aby tłok zaparzacza dało się łatwo poruszać. Następnie trzeba zrobić więcej jak pięć kaw bez ziaren, ignorując komunikat "brak ziaren". Wtedy maszyna powinna przestawić na dłuższy czas mielenia samoczynnie. Jeżeli chodzi o wodę pod zbiornikiem na fusy to musisz najpierw zlokalizować wyciek, wtedy mogę udzielić dalszych wskazówek. Pozdrawiam
Excellent video. Thank you so much.
I had not seen your video before I replace my piston on my elleta, I didn’t put grease on the 3 o-rings, do you think it is an issue?
No, that's not a problem. If everything is sealed, it will stay that way. The silicone grease protects the o-rings from damage during assembly.
Witam, mam problem w tym modelu ze cala woda leci do tacki po lewej stronie zamiast dyszami, zasylikonowalem łączenie ale nic nie dalo, sprawdzilem zaparzacz i termoblok, co moze byc przyczyna? Ekspres ma 5 lat, wymienic termoblok? Dodam ze na spieniaczu woda dziala ale tez troche cieknie
Молодець, толковый репортаж 👍🏻👍🏻👍🏻
I have some coffee grounds in the large tube that goes from infuser to heat expansion chamber. Is that a problem? Everything else looks fine. Pucks don't stay together but are not too wet.
It is normal for a little coffee residue to remain in the thick tube. The tube can be cleaned during any repair or when replacing the piston infuser.
Auch ein exelentes Video. Das umfangreiche reinigen habe ich mir damals bei meiner Cappucino auch nicht angetan. Lieber auch einen neuen bei BND Kaffeestudio gekauft
Please I really need some help :
I have a Delonghi Primadonna Deluxe S which doesnt want to froth the milk when using the carafe.
So have found a few video showing the specific faulty solenoid valve responsible for that OR the milk frothing coupling/coupler assembly.
Have just replaced both and still coming out just steam.
What could be ???
Thanks
Hi, before you replace any other parts, try to completely disassemble and clean the milk carafe. Make sure that all the screws in the cover are removed, then you can disassemble everything and clean it thoroughly. For this I recommend a milk cleaner like this one, it's cheap and available in any drugstore: amzn.to/4gRqDC6
@ Honestly I did it a few time ,took the screew out and give a proper cleaning(i dont think the carafe will be faulty)
Have replaced since I asked the question,the top solenoid valve ,and I have realised it does have one more under the front cover…
Any other clues what might be the issue?
The steam is coming strong when trying to froth the milk but is not sucking any milk from container.
The milk foam is created in the milk container, not inside the machine itself. It is important that the steam pressure is strong enough to draw the milk. Additionally, the water pump must be functioning properly to generate sufficient pressure. I also recommend trying a different carafe, as it may happen that these no longer work properly after a certain time.
@ possible the water pump to work fine for coffee or anything else but not for the milk frothing? Manufacture year on the pump is 2011 ,so might be too week?
@ I have uploaded a video if you can have a look at it ,might give you a better idea.
Much appreciate
This is been extremely helpful, thank you. I have a ECAM 23.220 B-NN1,
Looking to buy the new replacement mechanical valve , I am finding a lot of part numbers that all look the same summer called ‘infuser piston’ etc. I haven’t purchased an O-ring kit to rebuild my infuser piston. But unfortunately, I broke the small flange that holds the output silicone hose
I have only one question.
I found a small 1cm round wire that looks like a miniature key ring. It came from somewhere on the left-hand side when removing the screws to get to the mechanical valve.
Unfortunately, I can’t add a picture here. But perhaps you know what it is?
Thanks again for your brilliant service !
Do you mean the ring spring that is stuck on the steam lever? www.juraprofi.de/DeLonghi-Ersatzteile/Gehaeuseteile/DeLonghi-Dampfregelknopf-ECAM::9817.html
Should I lubricate large red o ring ?
Yes, you can grease the O-ring a little.
@yt.myworks Replacement worked perfectly! Merry Christmas ⛄
Thanks very much for this video.
My machine is now working again.
I do have a question though.
How do I release the electrical cable to detach the front screen at 1.54 in the video?
I've watched it several times and tried to release it on my machine but can't seem to find a way?
Hello, the plug has a small barb that needs to be pushed slightly to the side, but be careful as it can easily break off.
@@yt.myworks Thanks for the info.
Is the barb on the left or right side of the plug?
Super video! Thanks for sharing it!
Awesome video. Thank you so much. Unfortunately mine got worse and makes no coffee now so clearly i did something very wrong :(
Did you replace the whole part like I did in my video? Check all connections thoroughly to ensure that they are properly connected.
@@yt.myworks I replaced the full part and ran it with the top off to see why it wasn't working and the water was going into the part but just spraying straight back out. No water was taken in and distributed to any part. Steam wand and coffee didn't work at all.
My machine become. Louder when brewing how can I fix
Excellent . Thank you!!!
Thank you for your efforts brother, I have changed the piston infuser with new one, but the problem got worse 😢 and the coffee collector drawer is now full with water compared to small amount of water 😢. What could be wrong?
It won't be the piston infuser, as long as you have connected everything correctly. Did you put o-rings on the hose ends? You have to watch where the water comes from.
Dzien dobry. Mruga mi ciagle lampka poziomu wody. Po kazdym plukaniu i zrobieniu kawy to sie pojawia. Trzeba przekrecic pokretlo spieniacza tam i z powrotem aby zgaslo. Co moze byc przyczyną? Dzieki z gory za odpowiedz.
DeLonghi Esam magnifica 3000b
Witam, to oznacza że do układu wody dostaje się gdzieś powietrze. Sprawdź najpierw uszczelkę zbiornika wody w miejscu połączenia z obudową maszyny. Zbiornik musi dokładnie dolegać do obudowy. Usuń ewentualne zanieczyszczenia, często zbiera się w tym osad z wody.
@@yt.myworks wlalem do zbiornika ocet z ciepłą wodą wczoraj i zostawilem na chwile. Przeczyscilem octem miejsce gdzie jest czujnik wody i obudowe kolo zbiornika. Właczam, plukam ikonka sie juz nie zaswiecila🤝baja
where did you get the blue tool from to take off the tubes?
AliExpres or amzn.to/3VdPuIe
Thank you ! 💯
Ich habe mein Gerät erst seit 3 Wochen. Auf einmal tröpt das Wasser nur noch plus ich habe Wasser im Auffangbehälter. Ich habe weiches Wasser 7,6 dH und ich benutze ein Filter. Ist wahtscheinlich wie hier an der gleichen Stelle defekt. Ich mach mir die Arbeit aber nicht. Auch, wenn hier alles 1A erklärt wurde, das sollte nicht so schnell passieren. Sehr ausführliches Video, Danke.
Dziękuję bardzo za super film😊. Przy okazji zapytam, jaka jest średnica oringów do wężyków teflonowych od podawania wody pod ciśnieniem które smarujesz? Pytam bo różnie podają 3,85x2x7,85 lub 4x2x8?
Witam, orginalny rozmiar to 3,85x2mm jest ale trudniej dostępny. Osobiście używam 4x2mm też pasuje.
@@yt.myworks dziękuję bardzo za odpowiedź 🤗
Good morning, My Jura 6Z is not working is having exactly the same problem that you described in the video " Jura Machine Doesn't Make Coffee - Water/Coffee Runs Directly Into the Drip Tray" , however the pin from the stepper motor of drainage valve is completely out, Does it have to be out or in with the power off? in your video it is in. Do you think this motor is jammed? how can it test it? Thank you for your help😀
Hi, when the machine is switched off, the valve is pushed out by the steel spring. In this state, the valve is closed. When the machine opens the valve, a loud clicking sound can be heard. Very often, the seals in the valve are worn out and the coffee flows into the drip tray. You can replace the gaskets or the entire valve with a new one.
Thanks for the quick reply, is there any chance for me to send you some pictures? The pin I am taking about is not the one in the valve, is the little stepper motor shaft, the one that press the valve pin. In your video when you remove the brewer unit I can see that the motor shaft is in not out. In my case it is out with the machine disconnected. When the motor shaft is out then it press the valve pin and hot water goes to the drain when it is in then the valve pin is depress, it opens the valve and the hot water goes to the brewer unit, is this right?? 🤔🤔Thank you.🙏
Good job nice manual! Thank you!
I just did this repair with new unit. Water does not flow through the brewing piston. Any ideas?
Where does the water flow now? Where does the water collect?
Witaj. Mój ekspres DeLonghi Magnifica S robi kawę lecz jest bardzo słaba nawet przy ustawieniu mocy na max. Wody leje tyle ile powinien nie ma wycieku do tacki z fusami jak na filmie. Czy przyczyną bedzie infuzor? Czy może być duża uszczelka na tłoku? Ewentualnie czy te infuzory co są na aukcjach do magnifica s pasują do wszystkich niezaleznie od modelu Ecam? Dzieki za odpowiedź pozdrawiam.😊
Witam, przypuszczam że przyczyną problemu będzie za krótkie mielenie ziaren które powinno trwać około 6-7 sekund. Polecam wykonanie czynności z mojego innego filmu: ua-cam.com/video/OJWguSgyf4c/v-deo.htmlsi=8bJ8E-Ovn1ob9pCU. Rzecz w tym aby zaparzacz i cała reszta dały się łatwo poruszać bo w innym przypadku ekspres redukuje ilość mielonej kawy. Uważaj aby starannie złożyć zaparzacz to jest bardzo ważne: ua-cam.com/users/shortsmOxrMerZSFo?si=WGvZDaVGl9IUiG__ Dalsze wskazówki później. Pozdrawiam
@@yt.myworks Dzięki za odpowiedź. Co do zbyt krótkiego mielenia, krążki z kawą wyglądają ok, gdyby było za krótkie powinny być mniejsze? A i zapomniałem dodać że próbowałem robić kawę na dwóch różnych zaparzaczach i taki sam efekt.
@@przemysawkasinski443 Sprawdź grubość zmielonej kawy, powinna być drobna podobnie jak cukier.
@@yt.myworks wydają się być normalne . A czy infuzor odpada w takim razie?
Jak jest szczelny to tak, należy skoncentrować się na proporcji zmielonej kawy i wody.
So sad to find this video just after I finished re-assembling my ECAM, would have saved me some time J
I want to buy a used one. But the seller writes that it started making liquid coffee. What could be the reason, can you tell me?
Hi, there can be various reasons for this. In most cases the piston infuser needs to be replaced.
God bless you king ❤
Hallo
what do you polish with? in Jura videos?
ua-cam.com/video/4iV0qUWUKAY/v-deo.html
W moim Delonghi Dinamica właśnie pojawiła się woda w pojemniku na fusy i mniejsze kawy były zaparzane. Poczytałem trochę i zauważyłem, że po wyjęciu zaparzacza w infuzorze jest woda. Sitko w zaparzaczu jest czyste. Ekspres na gwarancji. Półtorej roku nic się nie działo.
Nie może być wody w infuzorze (przezroczysta część). To oznacza że pojawiła się nieszczelność. Po półtorej roku nie powinna pojawić się taka usterka chyba że ekspres używany był bardzo intensywnie np. 10 Tyś. kaw.
Where do I get piston infuser ? Thanks
You can get it on ebay or amazon: amzn.to/40dPuc8
Hello, thank you very much for your video. I replaced a new brewing piston followed your video. Unfortunately there are still a few water drops in the ground collecting container after making coffee. Can you please advise if this is normal.
Witaj. Nasz automatyczny ekspres kawowy Jura S8 będzie wymagał konserwacji. Czy podejmujesz się również takich zleceń? Jak mógłby się z Tobą skontaktować?
Witam, niestety nie proponuję takich usług. Pozdrawiam
I'm interested why you bought a new brew unit and didn't service it like you've done in the past. What were the problems that made you buy a new unit? Thanks for your great videos.
Hello, sometimes the brewing piston can no longer be repaired if it is too badly damaged. On the other hand, replacement is much easier than repair.
3:58 Almost impossible to find these in the right size.
www.juraprofi.de/DeLonghi-Ersatzteile/Schlaeuche-und-Verbinder/Klammer-DeLonghi-fuer-die-Schlauchverbindungen::7041.html?refID=gbase&gad_source=1&gclid=CjwKCAjw8rW2BhAgEiwAoRO5rO7aKGauKc4YM1vPtD3gPM5zIFJkyLZc1oEfMcUdJ58lthnm162ohRoC7sYQAvD_BwE
Can you make some video of service with 370.95?
The Delonghi 370.95 has an almost identical structure, only the housing and the control panel are different. You can see how to remove the case in my other video: ua-cam.com/video/4iV0qUWUKAY/v-deo.html
Holymoly....its like 5000pieces puzzle....😂
Anyways, thx a lot
Hi, where do you buy your spare parts from? Thanks
Hello, I often buy from: juraprofi.de, komtra.de, ebay und amazon.
Ciao ho una magnifica S macina il caffè ma non scende anche l’acqua.
It could be that a water pipe is calcified and clogged.
Quindi dipende dalla tubatura intasata?
@@claudioviscomi248 If the water pump becomes very quiet and the water doesn't run out anywhere, then yes.
Woow❤❤❤
Hey great video, I followed it all but decided to try fixing my current piston instead (following your other video) but now that I’ve put everything back together the machine does nothing, it just flashes the red triangle when I turn it on and nothing else. I checked the diffuser already like it says in the manual but it didn’t help. Any ideas what the problem could be?
Good video, except that i must have broken the connector to the motherboard as this cannot be fitted back. Just falls off. Pity no attention was aimed at that. All i can see in the video is that it's pulled off
Can you please advise if o-rings are already in the new brew unit. I didn't have them and the old ones didn't come out with the three plastic lines that attach with clips, so was presuming they were already in place?
Hello there. My maschine acts Weird. It gives some wet pucks, not super wet, but definitely wet. When I then try to descale the machine, most of the water runs out on the table ;( do you think it’s this part that are defect? Will I be able to see where it leaks, if I remove covers on the unit and try to run a descale? Of course I’ll be aware of electric shock.
Hello, you describe several problems that may have different causes. The wet puck indicates worn millstones or incorrectly adjusted grinder. Calcified heating casing can be responsible for water loss. And if the machine is more than four years old, then I generally recommend replacing the brew piston.
@@yt.myworksmaybe its calsified beating casing, where is that located? I havent touched the grinder. Its from december 2021. But we have very hard water with alot og calcium in it.
Ciao c’è la possibilità di mandare un video così vedi il problema su WhatsApp. Grazie
yt.myworks@hotmail.com
My machine become. Louder when brewing how can I fix
Where do the loud noises come from? Grinder, water pump or transmission?
@@yt.myworks it grinder, noise while brewing