How to test a Transmission Solenoid

In this video I show how to electrically test an On/Off DC solenoid taken from various transmissions and manufacturers. These particular Solenoids are electromagnetic switches that are used to control oil valves.
To find out more tips on automobiles check out the link below
agm-transmission-llc.business...
I am not affiliated with any of the products used in this video. By watching this video you agree to test solenoids at your own risk.
Due to factors beyond the control of AGM Transmission LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.
AGM Transmission LLC assumes no liability for any property or personal damage that may arise from doing a diagnoses on your vehicle after watching any of my repair video's.
Due to factors beyond the control of AGM Transmission, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.
Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not AGM Transmission LLC.

[@ennisgunns]

Best video I have seen.
I cannot remember anyone else discussing watching the piston move.

[@mattdathew2794]

thanks a lot bro, i was puzzled on how to test my 1 prong solenoid

[@MelissaMartinez-ge1kd]

The clicks I heard from the "good" solenoids were the same clicks I heard when you sent the 12volts to the bad solenoid. The only way to know if it was good was when the valve moved like it did in the first solenoid you tested. Thank you for the examples this video was still helpful 👍

[@keech2540]

Very useful video thank you! I have been testing some solenoids and I know, or used to know, almost nothing about these things. This helps me see that a bad solenoid will still click but the plunger wont move. My solenoids have moving plungers and clicks but I don't think the plungers are actually moving far enough with each actuation.

[@laykhom3212]

Is the solenoids bad when it makes no clicking sound when you test it

[@aliejaz581]

Goood video sir. The last one that you tested that for tranmisssion or vvt valave?

[@brianfessenden5400]

I have a DTC p0777 on my jeep. I've never dug into a transmission other than replacing a torque converter. Hopefully this isn't too bad for the solenoids

[@himaforlove]

👍👍👍👍👍

[@matermark]

Is there a way to check 4l60e solenoids thru the electrical connector without removing the pan? Thanks.

[@ennisgunns]

Yes. With a bi-directional scan tool.

[@joeschleprock3409]

Do you know how to test the trans transducer? (dodge 46re trans). thanks

[@richieborces3908]

next time you should use the prescibe colorcoding

[@user-zv9pm7mm6y]

How to remove shift solenoid on front wheel drive 2009 Cadillac DTS

[@noorrasooli7121]

My car 2015 Hyundai Elantra mover reverse but not move on drive gear.

[@bortiz5260]

Which one is p2714 shift solenoid

[@canbaran1477]

Hello selenoid code resset?

[@scotteric8711]

9V batteries work in most cases too.

[@tylerdaby3080]

Which one is the solenoid B ? The left or right one

[@femensah]

A=Right
B=Left

[@canbaran1477]

Video

[@alexmurray1639]

They can click and still be bad no?

[@leslielissethlopezchavez6752]

Toyotarav4 no entra la velosida 3y4

[@omgcheeter]

Es 2001-2003 ?

[@khalidawad9294]

You did not show us the electrical source and the voltage and wiring layout .. this is most important than what you've shown

[@mechboy5954]

He mentions they are 12 volt, 2 pin Solenoids. You do not need a wiring diagram for a 2 pin solenoid, and the electrical source is a battery because that is the only 12V source on a car

[@charleswaynewright2042]

Another thing to is where he finally connected the phuken ground