thank you for this video its very helpfull, i have the code p2716, i have to change the solenoid D? is it the same process?
You’re most welcome. Yes, it is, but you might as well change all, due to other ones being old as well
Ese solenoide es del cambio de velocidad 1ra 2da y 3ra ? Buena tarde!
Thanks for this video. So I have the code p0746 showing on my mitsubishi outlander (Jatco JF011E) , alongside a stepper motor code p1777. Local garages don't have the balls to take on the job so going to do it myself. Is this pressure control solenoid situated on the valve body itself? I have found a brand new oem valve body for cheap so wonder if it's a good idea to just swap the valve body? thanks in advance
@@igorbogdanoff4517 the control solenoid is on it. It’s a step toward fixing it.
I have a 2008 Toyota Highlander limited. Reading same code. Had the solenoid replaced, but the same code is still appearing and it still want shift properly into Drive, but yet it shifts properly in the other modes shifts properly , meaning I feel and hear the shifting gears when I shift but not in the (Drive) mode and it also want drive as it should. What's next?
you might have to check the wires and connector to the particular solenoid. Check the wire for resistance (ohm) and voltage if you could.
Thank you very much. My 2008 toyota sienna when is parked overnight, in the morning when i go to drive, I have to go over 4000 rpm for the car to move, when the car get hot I have no problem. Do you think if I change the solenoid it will fix? I have this problem of over 6 months and just one time the car showed the code P2714. I did a scanner and clean the code and never showed up again.
Hi , I have 2006 Toyota sienna with almost 200k miles. The transmission is acting up , I got code p0776 and p0746 I changed the 3 short solenoids and it got shifting well again but after driving a little while it doesn’t want to go back into first gear if I stop, please help
Have you considered changing the valve body, and the seals around the valve body?
My 2009 Toyota Camry 3.5 le has code p0746 pressure control solenoid A. Which one would it be?
My sisters car had only 2nd and third, used a code reader. Said it was solenoid SLT, S4, and SL1, I changed those and now it doesn’t even shift into ANY gear at all. I’ve took it apart twice, changed the solenoids again and still nothing. I don’t get what’s wrong with it.
One day when I go into reverse I have a strong shock and vibration. The oil was very dark brown and I changed all the oil but the symptoms are the same. However, in drive it takes a while to start and then it is fine in the next gear. The code is P0771. Do I need to replace the valve body?
How much oil did you put in after assembling, thanks
@@adancardona8034 I put 3.5 quarts. After that, I kept putting 200ml at a time, until the dipstick shown normal level
How many bolt are hoding that valves body. I cant figure out. Which bolt only have to remove thanks😊
What was the 2nd piece you taped after the spring, and what does it do?
I just read a comment where you answered it's check valve but how important it is because i just finished put everything back and i could not figured out how and where supposed to go. I also found 3 loose tiny ball bearings and no idea where they came from.
The second tape was just to secure the check valve, because one tape was not enough. It is important, because it controls the transmission fluid that passes there. For the 3 loose balls bearing, you’ll the repair manual for that, because those balls also allow and close the fluids pathways.
What diagnostic tool you using to see the solenoids, and do you know what to look for when buying an obd2 scanner so you know it will let you see all electronics in transmission
Thank you,
I have an op500 code I already changed the 2 sensor and my 2004 sienna is still slow to shift from second to third gear, what I have been doing is to release the gas pedal to give time to transmission to catch up with the actual speed so it’s doesn’t sleet. I am suspecting of a stuck or bad solenoid even though I am not getting the infame code.
I will drain and fill today
I replaced the abs module and it has fixed the OP500 code, but I still have the transmission issue
Mine is doing the same thing I do the same thing I left off the gas pedal to let it catch up did u figure out what the problem is
@@DJBOOGDAGREATI have been researching into this matter and I was reading that some of this transmissions are just like that, they won’t fail because of this, that’s actually a good thing!!! A person in that forum was actually stating that his sienna was that way when he bought it brand new. It won’t cause any problems they keep going and going! It’s annoying I know!
I will change the after market cv axles for OEM, I still have them, I will install new boots and see if this fix the problem, because mine didn’t have that shifting problem when I bought it, I didn’t pay attention but I think this appeared right after I replaced the OEM cv axles for the after market ones. But at the end I am not in a hurry I know it’s going to be good.
Last November I was ready to swap the transmission but I find out that some of this transmissions are just like that!
My 04 Highlander gave po776
Weak take off till it got momentum
Then it shifted hard 2nd and 3rd gears, I replaced all the solenoids. It still got weak take offs but the rest shifts smoothly. Why do you think ?
@@drue2283 (don’t quote me, I’m going by memory) I believe it is 13 ohm
Hi i jus change on the same car and i don't have reverse or neutral everything get to the front like n r
Hello guys I have a 2004 Toyota sienna AWD U151F that works good on drive but won’t go reverse, the same code popped up is the solenoid bad or the whole transmission ?
(1) Check the fluid level first (2) drain and refill the fluid (3) the valve body
4:12 I would like to know what he put in the second teip
No, after the spring. It looked like a bolt that went into the side of the spring. How do you keep these from popping out m if that’s possible.
Hi, i have a 2009 toyota sienna le. 3.5 engine. Is the transmission is the same as yours. I have a cose p0714. My car jerk in 2 and 3 gear. Is hesitate in second and go. I dont know what to do. But just keep driving like this for 4 month now. What could be the main problem. Thanks😊
Yes, it is
04-06 (3.3L): U151E
04-06 (3.3L): U151F [AWD]
07-10 (3.5L): U151E
07-10 (3.5L): U151F [AWD]
First, check the level of the fluid, 2nd drain and refill the transmission fluid
I'm only drink one time and is not work. Maybe I should I drink more. The oil is like dirty. Thanks
There’s a filter inside the transmission. That needs to be replaced every 30,000 miles or 50,000 miles
I bought all my solenoid kit already. But I'm not sure which one is the cause problem. What happens to your transmission And which one is the one you replaced here. I'm never open a transmission before so. I'm still lost. Don't know what to do. Do you have the diagram to show all the solenoid locations. Thank you.❤
So a small spring and a black clip with what looks like a roller ball on the end of it came out when I dropped it where and what are those parts
It’s a check valve. it’s important to important to put it back. You see the part I put the tape on. That’s where it goes.
@@fixchanics9969 awesome I seen it after I watch a few more time Ty so much . Will I have to rest computer or anything after I’m finished ? I am working on 05 Camry with code p0764. Control solenoid A and just followed this video🤔
@@fixchanics9969 when you say resettled does that mean I can unhook the batter and do a hard reset or will a need a tool? And what tape did you use
@@jdee3093 you need a computer to reset it. I believe it’s called RESET MEMORY
Good afternoon sir. My sienna XLE 2011 showing codes P0746 and P2714. What number parts are those solenoid A- D please
@@anibalavendanomartinez7279 get them as a kit. And replace all the solenoids.
@@fixchanics9969 I am going to buy online but I don’t know the numbers parts
Hi my 2004 sienna awd drives good for 30 minutes. But after that wont go in Drive only in reverse. You think its the transmission? Not codes
It might be mechanical inside the transmission. Because it works when it’s cold, but not when it’s warm.
I had the same problem but after putting everything back together it got worse because in reverse it goes forward and in neutral too. What do you think the problem is? Can you help me please?
I actually only changed one, I didn't touch the others, I don't understand why @@fixchanics9969
What solenoid did you replace? I have the same issue with "B" perf/stuck off. I tested the line pressure control solenoid, shift solenoid valves: SL2, and SL3, and changed the filter (strainer assy.) But after putting back together its still slipping as soon as it shifts, or attempts to shift into 3rd
Was the transmission not engaging in 4th gear? What were the symptoms?
My 2010 Sienna only has 141,000 miles and it would be very disappointing to find I have a mechanical problem with the transmission.
Thanks for sharing your experience!@@fixchanics9969
@@louielouie7806 did you change the transmission fluid every 15,000 miles?
I wish, but I listened the manufacturer who said the fluid doesnt need to be changed, which I now realize was a mistake.@@fixchanics9969
Hi there..I have a 2004 fwd transmission that skips 2nd gear when shifting and hesitates a little in 1st gear too ..could that be because of a bad solenoid? @fixchanics please help
I have a solenoid d code and I can’t find a place to buy or a video addressing it
amazon and ebay should have it. Please be careful purchasing it, because most sellers ship them from china. And sometimes, they send out the wrong ones.
it's same principles, google the valve body of your vehicle, and it will show the solenoid. Solenoid D, should be SL4 (I'm going by memory)
hi, how are you? Do you have a diagram? to find which one is four and fit my no changed to four and five speed and where do you buy the selenoid
google u151E valve body images.app.goo.gl/6MV41BjgsiiUX36a7
number 4 is letter D. I bought the solenoid from ebay, and I tested them first with a multimeter., before installing them.
I have a 2007 highlander 3.3L AWD and when the transmission is cold it revs to 2000 rpm @25 mph and hangs up ...seems like it doesnt wanna shift after 25mph but once it warms up its fine. what is my problem?
my doesn’t switch to the third gear did you know where they located?
the third gear is SL-3. But drain and fill the fluid first though, if there is no code
Hi . I have a 2017 Malibu 1.5 and code p2723 solenoid stuck off E , is there a way you can help we with the diagram so I can replace it ? Thanks
i already changed the fluid ..5 . 5 qts toyota type 4 .. level hot shows fluid up to 2nd mark on dipstick
If there’s no code, it might be something mechanically wrong, torque converter, clutch pack, slater etc
good day mine his toyota 2005 wen i pack it for like 5hours nd it wont move on till i accelerate for like 3min before he moved please what can be done
Good morning, pls my 2010 toyota camry showing codes P2808, P0776, P0746, is it fixable or do i need a new transmission?]
An nother transmission please fluid starvation an no maintenance. 😢 clothes are burned. Transmission pump cannot an will not be able pump an maintain pressure. On its last miles. Like 30.000 Miles left.
Where is solenoid d located. My sienna have a code said solenoid d stuck off
@@fixchanics9969 got a code said p2714 pressure control solenoid D performance or stuck off. The car was hesitate when pressed on the gas. It was hang on gear or something. Then it drive ok after that. Don't know what which solenoid or what the cause doing that. Thanks
I can’t figure out what part I need what’s the name of that part
Solenoids A B C D…. They sell them as kit online. Try, Toyota Sienna valve body solenoids.
same problem sir just came across your video . This will be the 3 rd time dropping trans pan .
check the resistance and voltage on the solenoids and wire harness. Also, reset the transmission memory (you'll need a computer that can do that)
Just ran new trans wires(OEM) 75 bucks just put in. (OEM) s4 solenoid 350 bucks . Still will not go into 4th and fifth my next option to put back original Short DSL solenoid and clear codes . My original code was a PO798 . So I hope helps a future reader .
@@jesussavesletyourgooddeeds3623 you might need a new or rebuilt valve body. Were your transmission slipping before?
I have a 2007 Camry 2.4l. Do you know if the replacement of the solenoid procedure will be the same or is it completely different?
@@fixchanics9969 the reverse didn’t work for about a week but it was due to low fluid I put it on Jack’s to do some suspension work and it started working again lol gonna replace the #35240 OEM Toyota part# DSL solenoid this week . See if gear 345 will down shift . Will give update .
I need to replace solenoid B
please ? Could you provide the sequence of the fixing screws! I have a lexus 2000 es 300 and I couldn't remove it because I didn't know the correct sequence of the screws!
What was part u put under tape ?
the was the springs, one is a black plastic with small spring, and the other was the middle spring from the 3 big springs. They stay in place when the transmission is upside down.
Do you have any diagram for that please
Change all of them, I don’t have a diagram, but match each one you take out with the new sensor
Hi, i have an u140f transmission in a 2006 European rav 4. I have rebuilt it according to your guidelines, and after road test, when the oil is hot, it returns an p0746 error, and does not shift from 1-2. When I use the tech stream software i can force 3rd gear. I have replaced the SL1 solenoide, but that did not help. Any advice
I did this on a Japanese 2004 Toyota Sienna.!- did you reset/relearn the transmission computer. 2- check the wire harnesses for loads (ohm/resistance) and voltage. and 3- test the solenoid for proper loads (ohm/resistance) and voltage.
@@fixchanics9969 Thank you kindly for the reply ! Yes, we did relearn the trans computer via techstream. Voltages and ohm values are normal according to the service manual. We cleaned the valve body again - it shifts 1-2 with slip, but after the cleaning, the p0746 is on - but the gearbox still shifts instead of going into only 1 gear mode
@@Marcheva91 is it possible, maybe mechanical, the clutch or gears getting worn. Did you the check the spring gaps and strength?
@@Marcheva91 check the wires from the computer to the connecters, connectors to SL1 connectors
Hey sir please help me. Please guide me i have a same code in my prosmetic transmission of honda 2007 model. When i shift my car in reverse gear the gear engaged late and when i shift my car from reverse to D then it gives a shock and The D transmission light in meter is blinking . In p0746 My car given a code of pressure control solenoid valve A stuck off. Plz tell me what it’s fault and how i treat it .? Mechanic doesn’t understand this problem because these are not applicable mechanic. They are all have their own opinion. Plz guide me and rpl me plz. 😢
the solenoid needs to be replaced. you can do that by taking the transmission pan off.
Hey I got p0776 nissan altima 2017 solenoid stuck off B i I think fluid wasn't never change car wont go into gear was driving in into it drove like 5mph would not accelerate,
Good morning please can you help me on my Toyota Sienna early in the morning the gear doesn't move auntie when the engine is hot
@@taiwosunday4809 your clutch packs might be burned. in this case, you'll need a new transmission.
@@taiwosunday4809 please have you able to fixed it cos am having the same problem
Hello , I have an Aisin U150F unit in my Lexus Rx 180.000 miles .Having lately bumps between 2/3 upshifts occasionaly .
Changed the fluid lately 2 x
Can I continue driving whitout doing harm to the unit , the bumps are something that I can endure ,get use to.
Glad for your advice
My Greetings
It will eventually wear parts out, and become harmful eventually. Best, to check it out now before the transmission goes on limp mode.
@@fixchanics9969 Thank you very much for having time to write back . All the best to you.
Hi my Toyota Avalon 2006 model sometimes show a pressure soloniod error code and when I whip it with scanner it moves fine and come may after some days later and I noticed the ATF is somehow black,do you think if I change the aft in will make a difference.please what do I do.
@@eshems-engineeringeservice1 Most likely, that particular solenoid is becoming demagnetize, and eventually it will wear out completely
P0741
Ese solenoide es le a
Thanks for the video. I needed to know how to keep the spring and check valve in. 👍
I used tapes