Starts to clip when amp volume is turned more than than 50%. But below that, subwoofer level is more than enough for most music genre and listening levels.
Great job, super clean nice looking build ! Don't worry about some of these other negative comments. Not all ports have to be 6" X 12" slots or 6" round. The only reason for using a large port is usually to increase efficiency and reduce any port noise. A lower powered system as you built does not have that worry. I bet in the van it sounds pretty good. Again well done.
depends on the sub. if it needs 100 watts RMS then you should never give it less. otherwise you'll starve it. and like the name implies, same as in humans, if you don't have a proper power intake, you'll stop working sooner. so if you underpower a sub it will die sooner.
1000w speaker means that the speaker will strike at 999w or it will blow at 1001? At which frequency it will accept the 1000w? For how long? At which THD (%)? At which temperature and/or humidity? I have the impression that a speaker/amp complex is an active system with constanlty changing parameters where "static" specs like "1000w" simply does not aply.
Not even 150 thats max 80Watts with no controll or dampaning of the woofer and cause the box is small and not even calculated right it won´t be loud a all
Thanks for the feedback. Yes the amp is a bit underpowered for the sub but the total output is more than enough I need in my prefered level of music listening in and out of my mini van. 😊
Hi! I have a question i was planing to buy the exact amp that you bought But the subwoofer im going to use is a targa subwoofer it only has a peak power of 250watts so is the amplifier gonna toast the speaker at max volume or the speaker will handle max volume fine?
A quick question bro mounting the amplifier on the subwoofer box won’t create any complications by the jar & vibrations of subwoofer to the amplifier? Please respond...anyway impressed by your project bro..
Very good question. I enclosed the amplifier board with a scrap plywood and MDF, glued heavily to ensure air tight. Can be seen on 5:05 spot. Subwoofer air pressure, jarring and vibrations can damage the small electronic components on the amp board. :) Thank you for watching.
CHRCLMNKY Thank you for your prompt reply..I was with a big ? Mark for the past 1 month where to keep my pioneer amp in the car...well you solved it...it’s a bit heavy but I think I can fix it with bolts outside the subwoofer box...Many thanks
WHen you are installing power cables from battery (in most cases just +, and gnd is taken from the trunk) alwayz use one side of your car for power cables from bat, and other side for signal RCA cables from headunit. Just because you can get buzzing alternator noise from your loudspeaker. If you once get buzzing alternator noises you have to check your ground and make it better, if you still got this problem you can buy rca ground loop fix condenzators. Or cheapest solution is with a simple wire ground your rca conectors on the hadunit to headunit cover, this work :) Worked for me too, even im used different sides, ive got a BOOM sound when I turned off my engine.. Using a high quality rca cables could solve this , but its not recommended to install these cables together. Btw nice clean work , looks great, and nice MDF high quality materials are you workin with . Keep up the good work . For my builds , visit channel wutdafuqq22 on youtube. Sorry for my eng , homies.
Could have 'recessed' the amp a bit more to make it more durable and less subject to 'knocking' because you have the 'cut out' anyway. Nice clean finish simple look. Love it.
shout out for MR CHRCLMNKY his doing great a lot dhil po sau mrami aqung nakuha na idea panu gumawa ng mga subwoofer at im so amazed for your tools to use
@@chrclmnky sir baka naman maka hingi ng design ng box para sa pang sub woofer yun pong simple lang po at hindi kumakain ng space yun pong pang 15"to 18" na sub speaker.. ang amp ko po ay ace MA 4002N...400W
The amp can just deliver enough power for a minivan. You only need super powerful amps if you place the sub at the back of the trunk and if you show off to your friends.
that's pretty interesting. I noticed that you have a lot of DIY stuff going on here and wanted to know if you've ever tried the ozone generator method of getting rid of bad smells in a car.
it's supposed to be plug and play, like put a boxy thing in your car and wait, but I've never really done anything like it so I wanted to ask since it's supposed to be some sort of like "insider guru" level stuff that's super simple. I figured with your awesome DIY knowledge you might have heard of it. Thanks for the reply man :)
@@kimchifan1 This is a 1000w RMS Class D amp I purchased a year ago- ua-cam.com/video/DXXAAVbYStg/v-deo.html Currently editing a video of a 1500w RMS variant and will upload very soon.
Snoopy GaminG you can just say 30cm... you don't have to measure in mm... also, it doesn't matter what you think the port size should be, as long as it is properly tuned it doesn't matter.
No it does matter because if its to small you get portnoise and the effect of the port gets less and less the port cross sectional area shoud be at least 1/3 of the cone area of the speaker which would be 3,5 Inches in this case or 17cm
Cupid Stunt yea I also use pvc tubes as ports mostly just cause it’s simple if ein want do build something strong and properly I use the enclosure as port
Very good build bro, you're the only person I've seen to use (T-nuts) to install the sub woofer onto the baffle, I believe that is the only and secure way to mount a sub woofer, wish you had a better camera mic to capture the true bass response, what is the box frequency tuned to?
Thank you, James. If I can remember properly, the box was tuned to 32Hz? Actually the amp is so under powered for the sub but good enough for everyday music listening while driving around town.
Thanks, I appreciate your quick response, I am considering installing a small sub underneath my rear passenger seat, and I like your build, like you, I just want a casual bass boost, nothing to shake any panels or fixtures loose, just something to complement the Rockfords I installed.. Hit me up if you make anymore upgrades to your system, Thanks in advance!!!!
I apologize, Should have asked for a track list, Your bass test songs I have, I test them out on my DJ system often and drive my neighbors crazy, (LOL), I am watching your video again just to get a general idea of how to build my sub box, but I believe I am gonna use a Rockford Fosgate amp, I am not familiar with the amp you used. Once again, Awesome tutorial video bro!!!!!!!!! :-)
speaker aint 1000w that should be clear butt it does not really matter at all it is better to give it a little less power than that it says so you dont blow your sub accidentally
What's the problem? Interference? That is a thing of the past. It's already 2018 and we now have nicer things called "shielded RCA cables". Try it, they're nice.
Hello thank you for watching and leaving a feedback. Ported (or vented) subwoofers are designed to produce deep and boomy bass. And must've been the video has been shot using a cheap mobile phone, so sound is not accurate.
Hello how you doin. Amp just ok but a little underpowered for the subwoofer. But total output is more than enough to my listening needs, in or out the vehicle. There are available larger amp power and also larger in size. Check out at Aliexpress, search for "12v subwoofer amplifier board".
@@chrclmnky sayang naman sir sana nandito ka bulacan/pampanga area. sa amin lang sa malolos mga 10km na drive makakadaan ka ng mahigit 10 na car audio shop. ganun kahilig mga tao dito
@@chrclmnky sir, question po pala. naka 6.5" subwoofer ako LL 250w RMS. anong FPL ko sya iset? kasi parang nabasa ko pag maliit sub dapat taasan ang freq. tama po ba? salamat sir
Can I Use this for home ??? as a subwoofer and maybe add a set of stereo speakers to get a 2.1 system?????
Yes you can but it will not sound as loud like in a car
Why
Bro, where in pinas are u from?
Butuan City, Agusan del Norte sir
CHRCLMNKY ok. Medyo malayo pala. I was hoping you're near my area and would like to ask assistance in fixing my box. Hehe..
Nice work sir!
Thank you. 😃
i want buy thus
No clipping sound?
Starts to clip when amp volume is turned more than than 50%. But below that, subwoofer level is more than enough for most music genre and listening levels.
Hi Ike, possible ba na magpagawa sa yo?
Hello good morning, yes po, actually most boxes built were from different customers from different points in the Philippines po.
Is the amp powerful for home theater
sharma ji
Is your brain powerful enough to comprehend how fucking stupid that question is?
How I get dis amplifier..... I mean.......online... Name
Great job, super clean nice looking build ! Don't worry about some of these other negative comments. Not all ports have to be 6" X 12" slots or 6" round. The only reason for using a large port is usually to increase efficiency and reduce any port noise. A lower powered system as you built does not have that worry. I bet in the van it sounds pretty good. Again well done.
Yessir! Audio system not for showing off but entirely for music listening. ☺ Thanks for the feedback.
Τhe first reasonable comment I read about this built!
how did you create the subwoofer in the app.Please do a tutorial on that.Asking for the 2nd time.
Hello Nihal, there are ready made subwoofer models on the internet to download and export into TinkerCad.
Nice build but that amp is not powerful enough to drive that sub.
How much power does the amp provide and how much power does the sub demand? I thought a speaker would work with any amount of power.
It will "work" but its like connecting that sub to an headphones output, its nonsense to use an such small amp with that sub.
Is there a rule about the power demand or does it rely on the technical specs of each sub?
depends on the sub. if it needs 100 watts RMS then you should never give it less. otherwise you'll starve it. and like the name implies, same as in humans, if you don't have a proper power intake, you'll stop working sooner. so if you underpower a sub it will die sooner.
1000w speaker means that the speaker will strike at 999w or it will blow at 1001? At which frequency it will accept the 1000w? For how long? At which THD (%)? At which temperature and/or humidity? I have the impression that a speaker/amp complex is an active system with constanlty changing parameters where "static" specs like "1000w" simply does not aply.
Can a PA 80D 1000 w same as that amplifier can drive a 1500 watts 15 inc. subwoofer?
Only bass lang po ba sya ?
Yes that's what subwoofers are for.
600w PMPO is bullcrap specs. That amp is probably 150w to 200w at best however It will work.
😄😂
150w rms is good enough. Unless u have a very low sensitivity woofer, thats a different story.
Not even 150 thats max 80Watts with no controll or dampaning of the woofer and cause the box is small and not even calculated right it won´t be loud a all
1kw peak.. 250 Watts rms
I would give it 200rms
Plexeezda YT if you mean the Woofer you are right
wow its really awesome .
😆
Hehe, power cable and signal cable in a single harness.
That dog be like "oh new house for me"....
Nice and clean build
Thanks for the feedback. Yes the amp is a bit underpowered for the sub but the total output is more than enough I need in my prefered level of music listening in and out of my mini van. 😊
Yeah i figured out that sub is only 250w rms so i edited that out, but it should be enough for daily listening :)
I am from Germany and would like to build something like u. But this amp looks a bit strange...
Hello. Yes this amp is not powerful enough. The separate Class D mono amps are very good for subeoofers.
@@chrclmnky thx 4 answer, I really like to watch ur vids. Very interessting what u build
Hi! I have a question i was planing to buy the exact amp that you bought
But the subwoofer im going to use is a targa subwoofer it only has a peak power of 250watts so is the amplifier gonna toast the speaker at max volume or the speaker will handle max volume fine?
This amp is nothing. Get a separate and dedicated amplifier that has at least a thousand watt RMS to drive your 250w subwoofers.
@@chrclmnky maybe when i got a job 😂 I'm just saving up the money that my parents are giving to me 😊
@@anxiety1209 😆
Питание и тюлюпаны вместе, наводки не не слышал😃
Step 2 : Amplifier plate, pwede ba gamitin sa house yan at gamitin power supply is Switching power supply? Na mabibili din lazada? High 40amp?
Oo pwede. Mga at least 80A or 60A
Dili mn kaya ang box sir ga haming na. Gwapo n kung less volume lng para smooth
The amplifier don't make 800w, probably not more than 150w
Yes you are correct.
@@chrclmnky aniway good project
This makes me wanna to get my hcca 12.2 ready for stereo season but I fried my sound stream 2,5000
"calculated" without T&S parameters..
A really good box. Inspiring. What's the the name of the first jam in the video?
A quick question bro mounting the amplifier on the subwoofer box won’t create any complications by the jar & vibrations of subwoofer to the amplifier? Please respond...anyway impressed by your project bro..
Very good question. I enclosed the amplifier board with a scrap plywood and MDF, glued heavily to ensure air tight. Can be seen on 5:05 spot. Subwoofer air pressure, jarring and vibrations can damage the small electronic components on the amp board. :)
Thank you for watching.
CHRCLMNKY Thank you for your prompt reply..I was with a big ? Mark for the past 1 month where to keep my pioneer amp in the car...well you solved it...it’s a bit heavy but I think I can fix it with bolts outside the subwoofer box...Many thanks
Yes, traditional car amps can be bolted or screwed on the side or on top of the box no problem.
CHRCLMNKY Thanks a heap bro God Bless
Plug the port with a rag or something to test it sealed, it might sound better. Usually those lower powered subs like sealed boxes.
Bad design . Very little space between the port end and the wall .
Ok.
nice i love how the cable management looks :D
😃
CHRCLMNKY hi can i ask the title of the background music you used at 5:46 tnx😄
Track title: Huma-Huma - Not Too Cray
tnx so much :D
WHen you are installing power cables from battery (in most cases just +, and gnd is taken from the trunk) alwayz use one side of your car for power cables from bat, and other side for signal RCA cables from headunit. Just because you can get buzzing alternator noise from your loudspeaker. If you once get buzzing alternator noises you have to check your ground and make it better, if you still got this problem you can buy rca ground loop fix condenzators. Or cheapest solution is with a simple wire ground your rca conectors on the hadunit to headunit cover, this work :) Worked for me too, even im used different sides, ive got a BOOM sound when I turned off my engine.. Using a high quality rca cables could solve this , but its not recommended to install these cables together. Btw nice clean work , looks great, and nice MDF high quality materials are you workin with . Keep up the good work . For my builds , visit channel wutdafuqq22 on youtube. Sorry for my eng , homies.
Could have 'recessed' the amp a bit more to make it more durable and less subject to 'knocking' because you have the 'cut out' anyway. Nice clean finish simple look. Love it.
Thanks. 🥳
Sir 6inch woofer disign upload please
türk olan
burdayız gardaşım adam harbi yapmış ama
shout out for MR CHRCLMNKY his doing great a lot dhil po sau mrami aqung nakuha na idea panu gumawa ng mga subwoofer at im so amazed for your tools to use
Thanks Richar
LMAO! so much unnecessary hate in the comments, I swear these kids are so jealous of your new box.
Finally I saw your face brother. You inspires me to do it myself.
Maganda ay simple yang gawa mo sir..saan kayo na order ng jbl speaker at amp
Lazada po.
@@chrclmnky sir baka naman maka hingi ng design ng box para sa pang sub woofer yun pong simple lang po at hindi kumakain ng space yun pong pang 15"to 18" na sub speaker.. ang amp ko po ay ace MA 4002N...400W
Seriously? A decent box, a decent JBL loudspeaker and 600W pmpo amplifier, that is, some 12 W RMS ... It can not work !!!
It works just fine.
plug in a real amplifier with a real power of 300 rms, then you'll see how it can play JBL
The amp can just deliver enough power for a minivan. You only need super powerful amps if you place the sub at the back of the trunk and if you show off to your friends.
LOL. too weak if you want your whole neighborhood hear your boom boom. try that in the philippines, you will likely get shot.
30W R.M.S ua-cam.com/video/QzPNpCkdnCE/v-deo.html
Good work 😍
My favorite sobwoofer jpl🔈🔉🔊
Yee sir
Ka nice sa gawa mo ka idol harang pa
It’s awesome dude love it at the first video we had no internet and my account was lost so you remember me don’t you
^_^
Hi bro can you tell me what dimensions have this project
Good working 💪 👏
Hello Selim, there is a link to the Tinkercad schematics in the video description. Thanks.
@@chrclmnky😂😂
karpenter ka all machines kahase buy karna padega uska link dijiye..
that's pretty interesting. I noticed that you have a lot of DIY stuff going on here and wanted to know if you've ever tried the ozone generator method of getting rid of bad smells in a car.
My apologies never heard of about that. Sounds very sciencey.
it's supposed to be plug and play, like put a boxy thing in your car and wait, but I've never really done anything like it so I wanted to ask since it's supposed to be some sort of like "insider guru" level stuff that's super simple. I figured with your awesome DIY knowledge you might have heard of it. Thanks for the reply man :)
Sir can u give me some idea please
I bought 12 inch 1400w JBL subwoofer which amplifier will u prefer for it give me some options.
Hello Dash, get an amplifier that supports 1 Ohm load stable. With at least 1000w RMS.
@@chrclmnky thanku so much sir for sharing you precious time with us.❤️
@@Dash-Ø7-X anytime
Can this be used as a home theater subwoofer?
Hello Naveen, yes you can use this for home theater if you have a 12V 30A power supply.
@@chrclmnky thank you so much I was thinking of building this for my dj set up. 😄
@@DJ_Naveen218 To be sure, get a 12V 60A or 80A.
@@chrclmnky just for the aesthetics can I put the puwer supply inside the box?
@@DJ_Naveen218 Yes, power supplies can be placed anywhere.
I loved your work and always your first support
Thanks brother
There's no way to control the bass and extra no extra knobs!!
ok
Kamusta PA-80D ampli mo after 2 years of use? Nagkaroon ba ng issue? I'm planning to buy the same please help me decide based on your review. Thanks
It was sold right away after this build. Stay away from this kind of amps. Get yourself at least 100w RMS or more for car applications.
@@chrclmnky Any suggestion? Please share me the the link. Thanks.
@@kimchifan1 This is a 1000w RMS Class D amp I purchased a year ago- ua-cam.com/video/DXXAAVbYStg/v-deo.html
Currently editing a video of a 1500w RMS variant and will upload very soon.
Is that the woofer for the enclosure at 4:53 ?
Woof woof
Sanka po nagorder ng mga equipments mo? Shoppee po ba?
All online marketplaces
Nice but in my opinion the reflex tube is too small for a 300mm speaker.
Too small reffering to the lenght or the cross section of the tube?
Ernestom5 ccvc
Snoopy GaminG you can just say 30cm... you don't have to measure in mm... also, it doesn't matter what you think the port size should be, as long as it is properly tuned it doesn't matter.
No it does matter because if its to small you get portnoise and the effect of the port gets less and less the port cross sectional area shoud be at least 1/3 of the cone area of the speaker which would be 3,5 Inches in this case or 17cm
Cupid Stunt yea I also use pvc tubes as ports mostly just cause it’s simple if ein want do build something strong and properly I use the enclosure as port
Awesome clean build dude big like!!
tenx 😉😆😂
Too weak amplifier
It has distortion
Sir is amp ki price kitni he
Magaling po...maganda din po ang tunog kung may foam sa loob nkadikit sa wood...
Yes sir. :)
which ic or Transisgor is used in the amplifier?? and whats the fq range of the same.. if possible plz provide the link to the same amplifier
Please give me amplifier buy link pls🤗
Sorry I can't because I am not affiliated in any online marketplaces.
Why do you have a spam shirt?😂
I love SPAM.
Sir is that amp have long life ??
Need info please about amp
Yes it is durable. But not strong enough to drive subwoofer.
@@chrclmnky thanks for replying 😀👍
OK then I'll choose small sub for that amp
Very good build bro, you're the only person I've seen to use (T-nuts) to install the sub woofer onto the baffle, I believe that is the only and secure way to mount a sub woofer, wish you had a better camera mic to capture the true bass response, what is the box frequency tuned to?
Thank you, James. If I can remember properly, the box was tuned to 32Hz? Actually the amp is so under powered for the sub but good enough for everyday music listening while driving around town.
Thanks, I appreciate your quick response, I am considering installing a small sub underneath my rear passenger seat, and I like your build, like you, I just want a casual bass boost, nothing to shake any panels or fixtures loose, just something to complement the Rockfords I installed.. Hit me up if you make anymore upgrades to your system, Thanks in advance!!!!
CHRCLMNKY, What's the name of the second song played in your video?
@@MrJamesgrate Gunnar Olsen - Howling
I apologize, Should have asked for a track list, Your bass test songs I have, I test them out on my DJ system often and drive my neighbors crazy, (LOL), I am watching your video again just to get a general idea of how to build my sub box, but I believe I am gonna use a Rockford Fosgate amp, I am not familiar with the amp you used. Once again, Awesome tutorial video bro!!!!!!!!! :-)
Sir.. pano oo pag walang RCA OUT ang stereo.. pwede po ba tap na lang sa left and riightt rear speaker.. thanks
Upgrade nang head unit. Mura lang naman.
Buy ka ng line out converter
make a give away video of subwoofer please
Very soon my friend.
How much speaker watt
all funny comment..hu huh huh huh huh huh
Im broke af, and i dont got no tools of my own quite yet, any chance you wanna sell me that for cheap
how much did you get the amplifier for because I got my exact amplifier for $30AU off wish
Dude, NEVER buy anything of wish ! This site is just a huuuuuge scam
Iss amplifier ka price
may bagong labas ampli pa 80d 1000W swak padin sa budget shooppee or lazada
waow very2 strong ampli haaa...if that speaker shake? that mean?that speaker not strong enough,and that amplifier? big watts
600 w P.M.P.O Power ;D Real power 100w
Yes correct
Finally stumbled upon this, I have the same sub amp and was wondering what it sounds like.. Thanks for uploading the vid! PA-60A PMPO 600W
Hello, the amp sounds good, can deliver the right power for the subwoofer. Built-in active crossover is very accurate.
सर आप कंप्यूटर मे कोन सा सॉफ्टवेर यूज लेते लेतो हो बताना प्लीज
price of this box
Thanks bro...
What the software name for design..?
queeneira 2019 tinkercad your welcome
queeneira 2019 Tinkercad
Sir which is the amplifier board
The amp board is very weak and cheap. There are other way better amps.
a 1000 watt speaker and a 600 watt amp ??? however looks good
Jbl gx3001amplifire parfect subwoofer
สนใจคับราคาเท่าไร
Amplifier - 600w
Speaker -1000w
Is that good?
Hello Dinuka, amp is way underpower for the speaker but still good enough for music listening to any music genre inside the vehicle.
@@chrclmnky yes . You are right. Thanks
speaker aint 1000w that should be clear butt it does not really matter at all it is better to give it a little less power than that it says so you dont blow your sub accidentally
Dinuka Dayan its not 1000w it has a 250wrms
@@tommikurronen4384 that is what i sad dumbass
Gawa sana ako kso ano tawag dun sa kahoy na ginamit ..
Kamoteng Kahoy
I'm not happy with bass😣
Ok
RCA signal cables right up against the power wire lmao.
The box looks nice tho
What's the problem? Interference? That is a thing of the past. It's already 2018 and we now have nicer things called "shielded RCA cables". Try it, they're nice.
CHRCLMNKY Dayum son, where'd ya find that roast?
@@sethh8892 ik was like dayyuuummm😂😂😂😂😂😂
Beautiful
Thanks Anup
Looks nice...
Not too sure about the tune though, I hear alot of Uhhh, & not alot of nice deep Ommm...
Hello thank you for watching and leaving a feedback. Ported (or vented) subwoofers are designed to produce deep and boomy bass. And must've been the video has been shot using a cheap mobile phone, so sound is not accurate.
i want to use this amp with alpine sbg-844br 20 inch subwoofer. do you suggest?
Hello Mustafa, this amp is way underpowered for the JBL sub I used. Better get a more powerful separate mono or bridgable amp for your subwoofer. 😯
my sub 120 rms your amp maybe enough. Could you suggest another amlifier from aliexpres. Because i will make active subwoofer box .
Yes, there's a 200w RMS subwoofer amp plate in Aliexpress model number YD-800w. Just use this keyword "new arrival 12v subwoofer amplifier". 😉
Ghar ke liye please
Hey man great job! Looks really good. Looks better than pretty much any pre built box and I'm sure sounds really good too.
Kinsa man Ang nag ukab Ani HAHAHAHA
YOWNNN proud bisaya here HAHAHAH 🧡
Hye sir if i use woofer 10inch 350watt, this amp 600watt can support bass or not for long time??...tQ sir
Yes. Better use 1000w
600 W PMPO is about 30-50W rms for a jbl sub?
Nice job !! Brother, what's the screws measures did you use ? Congrats from Brazil.
Screws are M6
Nice ... The amplifier is it ok? I'm planning to get one just like that last year ... 50/50 sure.
Hello how you doin. Amp just ok but a little underpowered for the subwoofer. But total output is more than enough to my listening needs, in or out the vehicle. There are available larger amp power and also larger in size. Check out at Aliexpress, search for "12v subwoofer amplifier board".
Que programas es ese queusas para hacer el diseno ?
Never run your RCA's with your hot and ground wires you pick up engine noise through RCA cables awesome video dude speaker amp kit how much was it
Right but because of the Xcrossover in the sub you can not notice those noises
I need to by that amp. So plzz share that link
Przewód łączący wzmacniacz z głośnikiem to jakiś żart ?? 0,5 mm???
Nice job! Can you help me ? I need box dimensions for Pioneer TS-W306C
Thanks. Ok will post a link to TinkerCad later.
How to make a subwoofer. Just buy it. I have the same thing but i bought it at walmart for $20
Please provide me with link
napaka swerte ng mga taga butuan sir!!! idol! sana nandito ka po sa bulacal or manila sayang
Ha! 🤣 Wala pong hilig mga taga dito sa car audio sir. May mga kakilala ako mga 5 lang. 😂
@@chrclmnky sayang naman sir sana nandito ka bulacan/pampanga area. sa amin lang sa malolos mga 10km na drive makakadaan ka ng mahigit 10 na car audio shop. ganun kahilig mga tao dito
@@chrclmnky sir, question po pala. naka 6.5" subwoofer ako LL 250w RMS. anong FPL ko sya iset? kasi parang nabasa ko pag maliit sub dapat taasan ang freq. tama po ba? salamat sir
@@gilberttan7244 LPF? Set lang nasa 63Hz. Masakit sa tenga if mas taas pa nyan.
@@chrclmnky ngayon po nasa 80hz sya low pass filter. babaan ko pa po? 6.5 inches po ito
Nice diy can u give me a jbl sub. For my froject hehehe