Congratulations on 100K! When you were talking about how your channel is DIY projects you do in "free time" is probably what I like most about your channel. You aren't in a shop, with all the power tools and endless supply of accessories. You're a 9 to 5-er like most of us, and are doing the work in a residential garage. I just goes to show how possible these projects are for the average person.
Congrats Chloe on 100k, well deserved... Maybe the best Tacoma channel, has been really helpful in upgrading my truck, especially the Pop & Lock video and recent tire size comparison.
Congratulations, just started watching your channel after getting my first Taco. Very good production and you’re very upbeat and fun to watch and learn about my truck. Keep up the great content
Would it be a good idea to intall the fuse on the inside of the box rathet then at the back? And although the electric tape seems to really work well to cover the edges how would a U shaped hard plastic work for this purpose? But then again it might not be needed!? Also what about a cover for the end of tje brass fitting of the compressor? Amd finally for a cover magnets seem a great idea but what about 1 or 2 horizontal hindges at tje top with a magnet at the bottom too to keep it in the open position?
Watching you blow up the past couple years has been so fun. Chloe you rock! Love the install too. Air compressors are so handy... even to help others that have flats. I carry a Smittybilt for now but something permanently mounted would be great.
If you fabricate a lid I'd suggest adding some low profile foam or rubber insulation around the edge to prevent water getting inside the compartment. Magnets are a great idea BTW!
Great video, I'm getting ready to add OBA in the back of my truck, my concern is the size wires you ran, it seems that 10awg wire is to small, I noticed when you checked the voltage, you didn't have a full 12 volts... has that caused any problems?
Your videos are awesome. What would be an even better series would be to show us how you trained your dog to help you when it put into place and held the compressor box. 🤣
Congrats on the 100K milestone! No Instagram for me, but my 2 fave videos you uploaded (and I installed) were the Seat Jackers and Cat Shield. I wish you continued success and Taco enjoyment!
One thing I would do differently cause I installed the all pro version is use a silicone sealant instead of the sticky tape to seal the extra holes. It did not last in the rain up here in the NW.
Did you consider using door trim instead of electrical tape to cover edges...would be a little cleaner and wouldn't have to replace regularly due to weather.
You can replace the electrical tape with a rubber strip like they use on fender flares. It comes with 3M tape on it for an easy installation. Also you could use a clear plexiglass with magnets on the ends to give a cleaner look. You could also use the black rubber strip on it as well. You can also add black home door weather striping on top and bottom that is also put on with 3M tape. This would seal up the space between the two brackets you screwed on so that you stay dust free. I would also add that strip on the inside of the brackets to make a completely sealed plexiglass.
If I may add to the electrical tape finish ideas...the black plastic edging used as door edge protectors would work as well...just cut corners in a 45° fashion (like a picture frame) would give a real clean look.
You're so precious to us! I've just got my 2022 Tacoma Sports a few months ago, and found your videos, and yes I've made some improvements to this wonderful truck... Happy Wife Happy Life! Congratulations and please keep us up to date, and sharing all those wonderful people who help us stay safe, and happy on the roads of life.
Congratulations! Love your videos. Use some rubber channel around the edges . Trim like what is used around the front of the bumper when you cut it to install your front bumper
Chloe, Great video. I just bought a 2020 TRD OR and have binged your videos for two weeks. I have an off topic question from this video, What are the black and tan cases in the bed of your truck? Looking for storage options. Thanks and keep up the great work!
Love it I’m gonna do mine soon but you could take that electrical tape off and put the rubber u channel edge trim so it will look a lot more cleaner love all the stuff you do on your truck! Thanks for sharing!
I don't care what anyone says. I love your use of electrical tape. You are a great and well-rounded individual. You're smart, charming, beautiful, and your cheerfulness is like the whip topping. You're a great influencer, and I'm hoping my daughter looks up to you soon.
Congratulations Chloe 🎉🎈🥂!!! 100K!!! We watch your videos because you are awesome 👍!!! My favorite video was when you got Cody as a puppy 🐕 😀. I hope UA-cam sent you a plaque or something 🤷♂️. Keep up the great content Chloe! ♥️🌮🐶🐾
i just use a plug in compressor with the 120 volt outlet and an extension cord. I can set it up and sit in the drivers seat and watch the pressure gauge if its cold outside. its not as cool as this but cost me about 60 bucks and no work to modify the truck.
The first video I watched was about how you detail your wheels. I have the white lettering on my tires facing out and am always looking for a better way to clean them. I also like the wiring videos because I am not as comfortable with wiring and electrical projects. The only problem with the wiring videos is when you show the wiring diagram I have no idea what the different squiggly lines represent. I like older vehicles so I look forward to the land cruiser project. I find it helpful when you show some of the aftermarket products available and how useful they are.
Great job keep up the diy videos. Suggest you use fiberglass resin for the edges that you cut into the bed. It’ll help prevent fraying and after that is done you can put some rubber edging to help seal up the cover your going to put on.
The switch and air hose outlet fitting are not Particle when you fully load up the truck for camping ,it is very difficult to connect the air hose and when the item move around while driving, stuff may hit the switch Accidental turn it on, it is still a clean set up but need some improvement.
I cannot for the life of me find the video where you described what you used to secure the pro eagle pole to the side of your truck. Could you tell me what it is again?
Congratulations Chloe, you certainly deserve it your videos are well done and informative. Because of your videos I upgraded several items on my Tacoma
I use my email all the time but used “Liberty” once. I don’t have much to say or add. My favorite video is when you added a fuse box to your taco. Congrats on your 100k. Your a very good video maker as well as a inspiration and instructor.
It might’ve been nice to just have the quick connect for sticking out and have the whole compressor hidden behind the fiberglass. Do you think that would’ve worked?
Congrats on the 100k! Favorite video would be the ones fitting the 285s. @Seoulrig. I ran my single Arb compressor in that same spot, cubby cover on, in my second Gen with a trifold. I had a lot of dust make it’s way int there and ended up removing it. Now it’s in a hard case, still in the bed.
I can see two minor problems that may come up. Anything moving around in the bed could hit the switch just turning it on or worse damaging it. Second problem is similar with the hose connector. Perhaps install the switch in the box and turn the connector 90 degrees to keep them out of the way of accidental damage.
Yuuuppp. Congrats on hitting 100,000 Sub's!!!! Dual batteries would be nice, to run those extra accessories. Just saying from 40 year's of off-roading experience. 🙂😀😃💯👋🤞✌️👌👍☝️🤙🙌👏🙏
Congrats on 100k! My favorite video would be the desert does it seat jackers, or the oil change tools. I found your channel researching them. If I could make a recommendation, you should do a video for the Z precision 32oz cup holder mod. Pretty simple install, small buisness, something that honestly should’ve come standard on the tacoma. @Coldpunk
Congratulations on 100K! When you were talking about how your channel is DIY projects you do in "free time" is probably what I like most about your channel. You aren't in a shop, with all the power tools and endless supply of accessories. You're a 9 to 5-er like most of us, and are doing the work in a residential garage. I just goes to show how possible these projects are for the average person.
Congrats Chloe on 100k, well deserved... Maybe the best Tacoma channel, has been really helpful in upgrading my truck, especially the Pop & Lock video and recent tire size comparison.
seriously. this channel is definitely one of my top 3 favorites!!!
U should put switch in with the air Compressor so u don't damage it in case u have to load something in your truck
Congratulations, just started watching your channel after getting my first Taco. Very good production and you’re very upbeat and fun to watch and learn about my truck. Keep up the great content
Would it be a good idea to intall the fuse on the inside of the box rathet then at the back? And although the electric tape seems to really work well to cover the edges how would a U shaped hard plastic work for this purpose? But then again it might not be needed!? Also what about a cover for the end of tje brass fitting of the compressor? Amd finally for a cover magnets seem a great idea but what about 1 or 2 horizontal hindges at tje top with a magnet at the bottom too to keep it in the open position?
Watching you blow up the past couple years has been so fun. Chloe you rock! Love the install too. Air compressors are so handy... even to help others that have flats. I carry a Smittybilt for now but something permanently mounted would be great.
You do a great job with video quality & teaching. You should be very proud of your accomplishment!!!
If you fabricate a lid I'd suggest adding some low profile foam or rubber insulation around the edge to prevent water getting inside the compartment. Magnets are a great idea BTW!
@chloe , the compressor setup is still accessible after deck installation ?
Great video, I'm getting ready to add OBA in the back of my truck, my concern is the size wires you ran, it seems that 10awg wire is to small, I noticed when you checked the voltage, you didn't have a full 12 volts... has that caused any problems?
Hey Chloe, I always notice that compass on your watch. May I ask where you got that? Please and thank you. 😊
Hi! You can find them at various watch shops or on Amazon. Mine fits up to a 24mm strap. Hope this helps!
@@ChloeKuo 💙
Your videos are awesome. What would be an even better series would be to show us how you trained your dog to help you when it put into place and held the compressor box. 🤣
Congrats on the 100K milestone! No Instagram for me, but my 2 fave videos you uploaded (and I installed) were the Seat Jackers and Cat Shield.
I wish you continued success and Taco enjoyment!
One thing I would do differently cause I installed the all pro version is use a silicone sealant instead of the sticky tape to seal the extra holes. It did not last in the rain up here in the NW.
Congrats!! I would say my thing about your channel is that you support small businesses and truly use their products!
Did you consider using door trim instead of electrical tape to cover edges...would be a little cleaner and wouldn't have to replace regularly due to weather.
You can replace the electrical tape with a rubber strip like they use on fender flares. It comes with 3M tape on it for an easy installation. Also you could use a clear plexiglass with magnets on the ends to give a cleaner look. You could also use the black rubber strip on it as well. You can also add black home door weather striping on top and bottom that is also put on with 3M tape. This would seal up the space between the two brackets you screwed on so that you stay dust free. I would also add that strip on the inside of the brackets to make a completely sealed plexiglass.
If I may add to the electrical tape finish ideas...the black plastic edging used as door edge protectors would work as well...just cut corners in a 45° fashion (like a picture frame) would give a real clean look.
Glad your template worked... mine was a solid inch off... Very surprised but manageable!
It's always fun to see what you will post next Chloé. Congrats on your subscriber base. Well deserved!
You're so precious to us! I've just got my 2022 Tacoma Sports a few months ago, and found your videos, and yes I've made some improvements to this wonderful truck... Happy Wife Happy Life! Congratulations and please keep us up to date, and sharing all those wonderful people who help us stay safe, and happy on the roads of life.
Your vibe is lit I love watching these vids
Congratulations! Love your videos. Use some rubber channel around the edges . Trim like what is used around the front of the bumper when you cut it to install your front bumper
Chloe, Great video. I just bought a 2020 TRD OR and have binged your videos for two weeks. I have an off topic question from this video, What are the black and tan cases in the bed of your truck? Looking for storage options. Thanks and keep up the great work!
Love it I’m gonna do mine soon but you could take that electrical tape off and put the rubber u channel edge trim so it will look a lot more cleaner love all the stuff you do on your truck! Thanks for sharing!
You should use automotive finishing trim. Same one people use when they cut their bumpers or fenders up.
Nice work but the mount will likely rust & get water & mud in the holes & connections. Needs to be sealed & accessible fuse. Hope it works out.
I don't care what anyone says. I love your use of electrical tape.
You are a great and well-rounded individual. You're smart, charming, beautiful, and your cheerfulness is like the whip topping. You're a great influencer, and I'm hoping my daughter looks up to you soon.
Congratulations Chloe 🎉🎈🥂!!! 100K!!! We watch your videos because you are awesome 👍!!! My favorite video was when you got Cody as a puppy 🐕 😀. I hope UA-cam sent you a plaque or something 🤷♂️. Keep up the great content Chloe! ♥️🌮🐶🐾
Would a 2nd gen 2015 trd sport have the same amount of space in the bed side?
Did I miss something? Is there a cover or door available or will this be open to the elements? I don't have a tonneau cover.
Do u need a bigger wiring kit? To put it in the bed?
i just use a plug in compressor with the 120 volt outlet and an extension cord. I can set it up and sit in the drivers seat and watch the pressure gauge if its cold outside. its not as cool as this but cost me about 60 bucks and no work to modify the truck.
3d printing an external cover might be your best way to prototype. I am new to 3d printing, but I’d be happy to help!
To cut the small hole for the switch. It works good to drill out the four corners first
Congrats! I’m new to my 3rd gen Tacoma TRD offroad and really appreciate all you do!
The first video I watched was about how you detail your wheels. I have the white lettering on my tires facing out and am always looking for a better way to clean them. I also like the wiring videos because I am not as comfortable with wiring and electrical projects. The only problem with the wiring videos is when you show the wiring diagram I have no idea what the different squiggly lines represent. I like older vehicles so I look forward to the land cruiser project. I find it helpful when you show some of the aftermarket products available and how useful they are.
Congrats on the 100k! You put out the best 🌮 content 🤙🏻
Great job keep up the diy videos. Suggest you use fiberglass resin for the edges that you cut into the bed. It’ll help prevent fraying and after that is done you can put some rubber edging to help seal up the cover your going to put on.
How do you change the compressor filter ?
Wow 🤩 congratulations on reaching 100k subscribers. You deserve it
Great job, Chloe. I just found your channel and I'll keep watching. Interested in that Land Cruiser.
Great info! You’ve convinced me that I need a Decked Drawer system and now an air compressor. 😳
How much feet of wire did you add to the wiring harness to reach the battery?
The switch and air hose outlet fitting are not Particle when you fully load up the truck for camping ,it is very difficult to connect the air hose and when the item move around while driving, stuff may hit the switch Accidental turn it on, it is still a clean set up but need some improvement.
Nice job the only thing I would have done differently is put the fuse on the other side but excellent job
That way you don’t have to take it apart if the fuse blows
I cannot for the life of me find the video where you described what you used to secure the pro eagle pole to the side of your truck. Could you tell me what it is again?
Since I already have a locker, I utilized the locker wires in the harness to control other accessories since those wires were in the cab
SDHQ has a 15' Extension that goes from the compressor to the engine Bay. Then you just plug in your supplied wire harness.,
Congrats on the 100k! My favorite video would be the bed build comparison between your two trucks.
I've wanted to do this upgrade for a while now. Great job!
Another great video Chloe. Thanks for putting it all together and posting. I really liked it and may do this project on my Taco.
Congratulations Chloe, you certainly deserve it your videos are well done and informative. Because of your videos I upgraded several items on my Tacoma
Is it normal for toyota tacoma fog lights to be hot?I have the stock fog lights for my tacoma thank you in advance
Got rid of the bed stiffeners?
What do you do work wise beside UA-cam ?
I am a Software Engineer
I use my email all the time but used “Liberty” once. I don’t have much to say or add. My favorite video is when you added a fuse box to your taco. Congrats on your 100k. Your a very good video maker as well as a inspiration and instructor.
Congratulations 🎉🎊 on 100k subscribers Chloe you deserve it I enjoy watching your channel Im
Always learning more about trucks 🛻 on this channel 😎💪🏾
It might’ve been nice to just have the quick connect for sticking out and have the whole compressor hidden behind the fiberglass. Do you think that would’ve worked?
Chloe - My vote goes for your original 'underseat' location. But ... Thanks for the option 👍 😘
YOU DESERVE IT! Congrats!!!
Congrats on the 100k! Favorite video would be the ones fitting the 285s. @Seoulrig.
I ran my single Arb compressor in that same spot, cubby cover on, in my second Gen with a trifold. I had a lot of dust make it’s way int there and ended up removing it. Now it’s in a hard case, still in the bed.
Superb installation, looks factory.
Congrats on the 100K!
Congratulations on 100k!!
Congrats on the 100k! 🎉
I want to know which is a better location: in the bed like this video, under the front seat, or under the hood? Pros/cons/opinions?
im thinking about going the 15lb. co2 tank route.
I can see two minor problems that may come up.
Anything moving around in the bed could hit the switch just turning it on or worse damaging it.
Second problem is similar with the hose connector.
Perhaps install the switch in the box and turn the connector 90 degrees to keep them out of the way of accidental damage.
😂🤡
@danebliven I like all the review and install vids but found the catalytic shield install was most useful for me!
Electrical edge guard would be best for the edges of the truck bed.
Awesome work!
I'd probably mount the switch higher just in case you have items rolling around the bed, they don't flip the switch on.
now you got 2 air compressors👏👏 i enjoy you.
Yuuuppp. Congrats on hitting 100,000 Sub's!!!!
Dual batteries would be nice, to run those extra accessories. Just saying from 40 year's of off-roading experience.
🙂😀😃💯👋🤞✌️👌👍☝️🤙🙌👏🙏
Congratulations
OK An idea, Buy the door for the LH side that yours did not come with and used that door to close were the compresor is located.
That’s a great mod I like it good job
I have a question why does my tacoma make squeaky noises when I pass through small holes ?
Nice install.
Congrats on 100k! My favorite video would be the desert does it seat jackers, or the oil change tools.
I found your channel researching them. If I could make a recommendation, you should do a video for the Z precision 32oz cup holder mod. Pretty simple install, small buisness, something that honestly should’ve come standard on the tacoma.
@Coldpunk
Masking tape makes a good pattern to follow with your cutting tool
your a good kid! congratulations
@TRD_TOYO congrats on the milestone, favorite is actually showing what's on your med kit!
Nategm1, I think my favorite video is just the ones where you try random mods/accessories and decide if there worth it or not lol
@Jeffreysburrito , I love the cheap easy mods videos !! Congrats again !
I like the idea 😊
Congratulations 👏
That electrical tape is going to leave an oily mess around that area a few years down the road as the adhesive degrades.
Congrats. You rule
Nice work!
@claukizz90 - Favorite video is the underseat ARB compressor install!
Yay first. Love all your videos.
Congrats
Where’s the decked unit? Oh wait, that’s in the other one.
Congratulations👾
dannydandan03, congrats on your 100k. I would like to see install on spot lights.
hey theres all the oil i cannot find at Walmart anymore... lol
so sad their raised the price from $19.99 to $29
beautiful wow
Nice job keep it up God bless
Good video.