EXCELLENT video and commentary of what it takes to do this job. I like you didnt do any other that music overlay crap... I find a lot of 2 wheel drive trans but I needed 4x4.. Thanks again.
I got a great deal on a 1uz and 30-40LE tranny setup do this swap in a '90 4runner, the 2wd to 4wd conversion on the tranny has many a vid on youtubes which is well within my mechanical level to perform, I will be using a spitronics harness and ecu/tcu, my tranny DOES NOT have the 6pin or 8 pin connector harness for the solenoids, mine is a 3pin connector, my ring for the speed sensor IS NOT as yours(or others) with the 4 "arms" sticking out, mine is just a ring with grooves machined equally running the length of the ring, I havent disassembled the tail housing but for initial benchtop inspection, the gear that would turn the speedo APPEARS to be a separate piece from my "tone ring/gear", both are held in place with a snap ring on that out put shaft-it APPEARS that once I remove that snap ring the speedo gear and the "tone ring/gear" slide off as 2 pieces, I also dont have a "speed sensor/lock up sensor" found on the front driver's side of the tranny as I saw on other vids, I'm thinking the bellhousing is for a 6 cylinder, the hump at 12 o'clock that I've seen on other tranny vids is at 2 o'clock on my bellhousing, I dont know if that sensor is mounted in the bellhousing, I do see a threaded hole and round casting where a sensor might be drilled(?), do you think I have a useable tranny for this 4wd conversion, do I just need a 6/8pin harness,
Thanks for making this video I didn’t think my 99 4Runner transfer case would work with a t100 tcase because of the tail shaft pickup/sender issue but I just drilled the hole out and shimmed it and it all jives even though marlin crawler said it wouldn’t 🤷♂️ They like to sell the mc-31 adapter plate
I have a 2000 automatic 3.4 4x4 Tacoma and a complete donor 93 ls400 , I’m a veteran Acura master mechanic. But your a better man than me, there is so much involved especially with the Lexus transmission control
I'll probably show some more information about my setup, but there are so many variations of the 1UZ management, I couldn't possibly touch on all of them. Check out CartuneNZ for some of that though, he's got a TON of information about these.
I have not finished it, although it does run. I simplified and modified the Lexus harness to be a standalone engine management harness so it only needs a key on, start and fuel pump wire to run. I will be cleaning it up and wiring in a custom fuse box next. I'll do a video of some of that.
Nice conversion... can you do that to A650E from 03 gs300 ? I have complete engine transmission with harness planning to put it in a mud buggy .. thanks
The 650 is much more complicated. It actually has a drum and clutch packs in the extension housing. The only 4wd conversions I found involved a very complicated and custom adapter. I ruled out donor cars with that transmission for that reason
I found a Russian web site that claims they can reprogram 2uz computers and they make a conversion ucu to communicate on analog vehicle that do not have can communication is call all4swaps.ru
EXCELLENT video and commentary of what it takes to do this job. I like you didnt do any other that music overlay crap... I find a lot of 2 wheel drive trans but I needed 4x4.. Thanks again.
Awesome vidoe.. very detail and informative. Thanks for the oil for the seal... Nobody every did found out about this. Thanks for sharing.
Fantastic video... I am looking to fitting a 1UZ into my Gen2 Surf and this will help me a lot... Thank you..
I got a great deal on a 1uz and 30-40LE tranny setup do this swap in a '90 4runner,
the 2wd to 4wd conversion on the tranny has many a vid on youtubes which is well within my mechanical level to perform,
I will be using a spitronics harness and ecu/tcu,
my tranny DOES NOT have the 6pin or 8 pin connector harness for the solenoids, mine is a 3pin connector,
my ring for the speed sensor IS NOT as yours(or others) with the 4 "arms" sticking out, mine is just a ring with grooves machined equally running the length of the ring, I havent disassembled the tail housing but for initial benchtop inspection, the gear that would turn the speedo APPEARS to be a separate piece from my "tone ring/gear", both are held in place with a snap ring on that out put shaft-it APPEARS that once I remove that snap ring the speedo gear and the "tone ring/gear" slide off as 2 pieces,
I also dont have a "speed sensor/lock up sensor" found on the front driver's side of the tranny as I saw on other vids, I'm thinking the bellhousing is for a 6 cylinder, the hump at 12 o'clock that I've seen on other tranny vids is at 2 o'clock on my bellhousing, I dont know if that sensor is mounted in the bellhousing, I do see a threaded hole and round casting where a sensor might be drilled(?),
do you think I have a useable tranny for this 4wd conversion, do I just need a 6/8pin harness,
Thanks for making this video I didn’t think my 99 4Runner transfer case would work with a t100 tcase because of the tail shaft pickup/sender issue but I just drilled the hole out and shimmed it and it all jives even though marlin crawler said it wouldn’t 🤷♂️
They like to sell the mc-31 adapter plate
I have a 2000 automatic 3.4 4x4 Tacoma and a complete donor 93 ls400 , I’m a veteran Acura master mechanic. But your a better man than me, there is so much involved especially with the Lexus transmission control
Control unit and Tacoma 4x4 control unit. I have to see your truck running to believe in your technical supremacy.
great vid
Thank you very very much...👍
There's that oil hole as you stated on a CartuneNZ vid. Thanks for your NA market specific swap details!! Did you have success with
If you can upload a video on how to wire 1UZ .. that will be great
I'll probably show some more information about my setup, but there are so many variations of the 1UZ management, I couldn't possibly touch on all of them. Check out CartuneNZ for some of that though, he's got a TON of information about these.
🙋♂️🙋♂️ im from puerto rico
and im algo looking for the t100 passenger side drop transfer case adapter
What year T100 is the adapter off of? Great video!
I believe mine came from a 98. But any 4WD T100 with a 3.4 and automatic will have the parts you need.
NumbchuxSOAD thank you!
Have you finish the eng swap and what you did for the wiring
I have not finished it, although it does run. I simplified and modified the Lexus harness to be a standalone engine management harness so it only needs a key on, start and fuel pump wire to run. I will be cleaning it up and wiring in a custom fuse box next. I'll do a video of some of that.
Nice conversion... can you do that to A650E from 03 gs300 ? I have complete engine transmission with harness planning to put it in a mud buggy .. thanks
The 650 is much more complicated. It actually has a drum and clutch packs in the extension housing. The only 4wd conversions I found involved a very complicated and custom adapter. I ruled out donor cars with that transmission for that reason
NumbchuxSOAD
Thanks . Do you think 340 and 650 share bellhousing . I was thinking getting 340 if 650 complicated to convert into 4x4
I found a Russian web site that claims they can reprogram 2uz computers and they make a conversion ucu to communicate on analog vehicle that do not have can communication is call all4swaps.ru