Це відео не доступне.
Перепрошуємо.
Uniformation GKTWO Wash & Cure Review
Вставка
- Опубліковано 17 вер 2023
- Buy the Uniformation Wash and Cure Here here
Unifomation: geni.us/Unfomation
Get any printer working easily with the Photonsters XP Range Finder - www.thingiverse.com/thing:602... (watch my video for full instructions • How to Print Perfect M... )
Join this channel to get access to perks:
/ @fauxhammer
Buy WARGAMER - The best Resin for Miniatures yesthats3dprinted.com/pages/w...
3D Printer Cleaning Mat: geni.us/3DPrinterCleaningMat
This Video is part of our series looking for the Best 3D printer for Miniatures; www.fauxhammer.com/top-10/the...
Artis Opus FauxHammer Essentials Set: store.artis-opus.com/products...
FauxHammer Patreon - / fauxhammerblog
FauxHammer Facebook Group - / painthub
FauxHammer 3D Printing Group - / 3dprintedminiatures
FauxHammer Discord - / discord
Best Airbrush For Miniatures: www.fauxhammer.com/top-10/bes...
Beginner Airbrush: www.fauxhammer.com/featured/b...
Affiliate Links to support us.
Element Games - elementgames.co.uk/wargames-a...
Wayland Games - affiliates.waylandgames.co.uk...
Forbidden Planet: forbiddenplanet.com/catalog/?...
Amazon - www.amazon.co.uk/s?k=Warhamme...
Website: www.fauxhammer.com/
Facebook: / fauxhammerblog
Twitter: / fauxhammerblog
Instagram: / fauxhammerblog
Pinterest: www.pinterest.co.uk/fauxhammer/
Video Editing by VidPros: app.vidpros.io/r/J50Z26
00:00 - Intro
![BETTER cleaning & curing of 3D resin prints [EASY METHOD]](http://i.ytimg.com/vi/kL9TCjtPbw4/mqdefault.jpg)
I worked in a University research lab and this is how the ultrasonic with can lead to combustion: As it vibrates it causes particles of the fluid to go into the air. This creates air that is now an explosive mixture of oxygen and a fuel. If that mixture of air comes in contact with a flame or spark, you will get an explosion. Part of the safety training, and lab rules, is to never run the ultrasonic with the lid off, as it will fumigate the area, and always run the ventilation hood, to remove the explosive gas when you open the ultrasonic cleaner. It really is no joke, it can happen, and it's extremely volatile gas mixture. Should only be used in well ventilated areas, should have a fume hood, always run with lid down, and DO NOT, under any circumstances, have any ignition source around while using. I would bet the companies instruction manual or documentation has such warnings, thus protecting the company from liability.
Handy to know! Wow, cheers!
Absolutely, lower explosive limit for IPA is 2%. Autoignition temp is high, true but irrelevant if you have this operating next to non-Ex equipment. Flash point is 12°C meaning if the concentration of IPA in the air is above 2% and it's not freezing you can have a really bad time in your hobby room. There are ultrasonic safe organic solvents though.
I was actually coming to the comments to speculate this. My ultrasonic cleaner is a super cheap amazon buy (like
I seem to remember reading a guide to these: The US army stated you can use ISO with an ultra sonic cleaner however ISO and the item you wish to clean should be in a closed bag (like a zip lock) and the ultra sonic cleaner should be filled with water.
I used it that way because you need less ISO
@@smtkelly That's an interesting way to do it, and much safer. Great idea.
I was literally looking for a review of these items yesterday! Perfect timing :)
I'm completely new to this, and I'm learning all about 3D printing from this channel. Thanks!
Glad to help mate
Great review and I agree with you on the efficiency of the Cure station as for the Wash station the area should be well ventilated when using IPA or other volatile liquid especially making it safe for family members.
I am a recent new subscriber and amazed at the quality of your videos and content. You have lead me in the right direction, so much so I went with the Photon M7 Pro that you reviewed. But, it kills me you only have 65k subscribers, were gonna have to change that for sure. Thanks for the hard work, and keep us informed. I have never done UA-cam join or Patreon but think you may have changed that also.
Comment for the algorythm ;) Nice work mate. Love watching your videos.
I agree with the cure station, i kinda wish it opened from the front. You could then put it on a shelf above the wash station and save desk space. That was my plan anyway
Interesting!
I've been doing that for a while, but with water-washable resin and a used lab-type sonic cleaner.
Not quite sure how I managed to miss the video till now [old age perhaps]. Good review as always Ross )O(
good video, as always. Thanks
When I use it, I fill the tank with 5 liters of demineralized water and use a zip bag for freezer to put my prints in with IPA. I try to push all the air out of the zip bag. It works well and it's easier to manage the alcohol and not waste too much . After each session, I empty the tank using the drain and put the water back in the jar. With this technique there is less risk of combustion.
For the UV device, I agree with you. I don't know why they choose to open it by the top ( maybe it's more ergonomic when you want to put prints inside) but the combo printer, ultra sonic and cure take a lot of space.
what do you do with the used IPA that's in the zip lock bag?
@@jarrettguma5522 I put it in a recipient to reuse it for the next print if it IS clear enough or I use it for the first clean because I use a two baths method. First with used ipa to clean my print and remove the most of the resin and After the Sonic cleaner.
I have this whole set up and love it. But I did add a bunch of aluminum tape to the inside of the curing station. I’m thinking of adding mirrors… but I also haven’t had any problems with anything curing so…
Great review as always! Please keep up the great work!
Also I used a sonic cleaner once with the isopropyl alcohol and it's true. The explosion took out 30 square blocks leaving a huge mushroom cloud in its wake. Luckily, I survived as I was getting a drink, the blast pushed me into my lead lined refrigerator and ended up a few miles away. I was hurt, but safe.
Hope this never happens to anyone!
can we get a comparison on conventional resin vs water washable resin cleaning in this please?
If you turn your jugs side ways when pouring you won't get near as much splashing all over when the air tries to escape
Nice review of the pair. I have to agreed with you on the curing station. I DOES look like it should open frontward and the fact that the rather flimsy hinges are on the lid does make it look cheap. I'm a bit surprised at the rather large dimensions of the unit and the big sides which limit the volume of the curing station. That and the fact it's a top loader means entry and egress are all the more likely to drop prints and damage them compared to Elegoo where the entire lid comes off to allow open access to them.
The washing station looks like a deep fat frier for chips! I'd be keen on an ultrasonic cleaner though. I do wonder at how well the drain pipe will keep clear and not clog up with used resin after a while.
He didn’t mention it but there’s a foam sponge at the bottom of the cleaner to traps thicker liquids or tiny parts when you drain
Where do u install the o ring with the ultrasonic cleaner my friend gave me one but not instructions
Wohoo i got it right. I happily dismiss the 12k upgrade but will surely grab the wifi dongle 😊
Will you be reviewing the Apex-maker X1 next buddy? Currently sitting on a pledge for that thing but not 100% sure if its worth it...
Sorry that this comes so late, had a question.
If you're not as keen on the curing station, what would you recommend?
What cure stations have 3 light sources?
So, what're some comparables? What're the alternatives?
Has a consensus on the approximate time frame to run this at been determined? I know you said no longer than 20-30 minutes, but has anyone noticed a difference between say 5 minutes vs 10 minutes?
I have never had my small ultrasonic cleaner spontaneously combust with ISO 99 in it, even with the heating turned on (although I don't usually use it with heat on. I can set the temp on mine and i set it at 50c (122F) which is less than the boiling point (82c) of iso ). I tried it with heat on and heat off to see if I got any different results in cleaning and I can't see any difference as far as cleaning goes with the temperature I use. The advantage of heat is in drying after the cleaning. disadvantage is it puts more VOC into the air. but since its in a well ventilated area it isn't that big of a deal.
however on the ultrasonic cleaner instruction they don't recommend using iso as it can vaporize. and then some external source could ignite it. That however is not spontaneous combustion. this is what they say.
"Use water-based detergents. Solvent-based cleaners are generally not designed for use in an ultrasonic cleaner, and may damage the stainless tank surface in some instances. Solvents with low flash points - below 200˚F, are never recommended. Plus solvents are unhealthy for humans."
"Never fill the tank of an ultrasonic cleaner with alcohol, gasoline, or any other flammable liquids. They will vaporize, and could cause a fire or explosion, or release harmful gasses into the workspace."
However I use iso in mine on small parts with really fine details as I don't want them to get broken by swirling around in the other cleaner.
as long as you take proper care its perfectly safe.
Yeah I read later its the fumes that can cause issue., but also heard Uniformation have lowered the power oif this to reduce fumes, not confirmed, just heard it in a comment
I was thinking also that after some time placing your vat on the ultra sonic cleaner this could possibly lead to your alignment screws backing out and thus throwing vat and screen tolerances off. I myself do not own a rein printer at this time but just thought I would drop my 2 cents in. XD
can you use high speed water based resin and then just use water in the cleaning station
Tip....pour your bottles of spirits or washer fluid with the spout on top! 🎉
I was looking to get the Uniformation GKTwo, from your recommendations and to know how the Wash and Cure works in relation to others will be helpful, I know you will say it wash's and Cure's but your opinion matters to me ;)
Sorry my opinion on these is that they all do the same thing. and as you suspected, they wash and cure. The only difference I;ve seen is size.
personally I use the Phrozen for washing as a first stage, then the Uniformation one as a second stage. I use Heygears Station to cure becasue that one is the most industrial and mostly, becasue the door opens outward like a microwave so it;s easy to use.
@@FauxHammer Hi what Heygears Station model do you use?
I stand by mean green, the hand friendly version. All the other stuff I've seen are either corrosives, or flammables.
hey! did you remember the shipping weight of this two products and the printer? im looking to get the bundle
No idea sorry, is it not in the website?
What printer did you use for that big Wolverine bust? Thanks
I second this.
Have you got and or reviewed the Eibos Oceanus. Its a toss up between this bundle or just the GKTWO and the Eibos. But i like the idea of the ultrasonic cleaner, especially as i can use it for other things too
I have, i think it's okay. a bit cumbersome. I use an ultrasonic, it's pretty good.
@@FauxHammerI want to use water washable resin, would water be an issue in an ultrasonic cleaner? I guess it could lead to rust...:/ Have u had success with water in it?
Most Ultrasonic Cleaners use some variant of stainless steel. You will be fine with pure water for ww resins. @@nicholassmith5206
Hi ! Great Video ! Can you tell me (or give a link) where I can find big same type of sponge to replace the original one when I have to do ? Thks !
Which one? Sponge?
@@FauxHammer yes ! The sponge under the grid at 2.56 on your video !
@@arcathar7789 did t even know it had one. I’d contact Uniformation
I've had some resin manufacturers tell me via email that there is no such thing as over-curing in the typical UV curing chambers and thus there is no such thing as an optimum time. For engineering-like resins they are quoting an hour or two and even that length of time + 60C to get full strength. Maybe the cheaper resins have a maximum cure time .above which they degrade in properties . . .
This. There is the resin's final state and then there's being undercured. We've tested curing prints for days under heavy duty UV hoods and they weren't any more brittle than when cured 8+ minutes per side.
Undercuring your prints to be more durable is a bad idea because it'll still off-gas, and will still be toxic to the touch. There are resins that existed out there too that literally change colour depending it reached that final state or not. So "overcuring" really is not a thing.
Question would you recommend a brand other than uniformation for wash and cure stations if so which Thanks.
I quite like the gktwo wash and cure stations. Honestly. None of them wow me… they all do the same thing. I do like this ultrasonic cleaner though
Nice thanks!
So I have the first generation curing machine and trust me that is an improvement I've already had to solder the wires going to the LEDs in the lid because the repeated opening and closing eventually made them snap hopefully they fix that The UI or the controller I should say on the original is horrible it's just bad it's a off-the-shelf cheap timer system it's just bad and hard to control extremely hard to control I have mine set it 10 minutes and I never change anything cuz it is that hard to change they also had a smaller bolt with a bearing ring underneath it on the original version and that bolt did not protrude as far for that reason a little better also it had a red window which I prefer I don't like that green color but that's just a personal thing does it cure better it cures from every angle that's why I bought it and when I bought it that was one of the only ones that cared from all angles and from the standpoint of surface area nothing else back then touched it
i would like to know if the lid on the washer is sealed tight so now vapors can escape ?
it;s not sealed, there is a gasket preventing vapours leaving, but this is also apparently lower powered than most other ultrasonic cleaners to prevent this.
IS IT NORMAL THAT I CAN HEAR THE HZ SOUND?
ALSO IT IS KIND OF HARD TO PUSH THE BUTTONS IN BOTH THE CLEANER AND THE CURING STATION.
Does anyone make a curing station that can dry the prints after washing aside from Prusa? Seems like a no brainer to me?
If I didn’t already have the ANYCUBIC Wash and Cure station I’d get this
so you said the curing chmaber is sub par-and you have one you prefer.
what curing chamber would you recomend than?
Well, none really. the one I use is the one from the heygears reflec which is far superior. but nobody is gonna pay for that. mainly becasue the accompanying wash station is awful
@@FauxHammer Tbf you can buy the curing station stand-alone, it's just stupid expensive for what it is ($750)
How loud is the ultrasonic cleaner when running? In the past I've found that cheaper ultrasonic cleaners are extremely loud and annoying while in operation which is my only hangup with this product 👀
I often forget it on and it;s 2m away from me
@@FauxHammer fantastic. Thanks a bunch!
Also you do great vids, keep up the good work :)
One question remains, how easy is it to get the IPA out completely? I tend to clean my models with IPA, then clean off the IPA with water and I really don't want to buy two cleaning stations to have one for IPA and one for water. :)
Let it pour through the outlet hose then wipe the rest with tissue.
I’ve been looking for safer solvents you can run in an ultrasonice cleaner. The brand Liqcreate who I know for making resins sells a supposedly non flammable resin cleaner at 5kg for 75$ so that could be worth a try
Alcohols are dirt cheap, excellent solvents and relatively easy to recycle by curing then filtering the saturated liquid. The problem with the miystery washing fluids and different household cleaners is that you don't know what's in them, how will they react to different treatments, and usually aren't willing to evaporate quickly with leaving back only resin waste to cure and dispose.
Sun makes a resin detergent now, non flammable and works as good as iso. Only downside is you have to use the detergent and then rinse with water after
All hail the algorithm!
This cleaner is made to explosion proof standards on the electrical side!!! Also flash point does not mean that the liquid or vapor will ignite, you still need an ignition point heat (temperature) flash point only means that instantaneous combustion can occur all at once you still need the ignition source!!!
thanks for the info
does the washer have lees volume than the gktwo? It looks shorter
yes
@@FauxHammer ty faux 🦾
@@demonhogo np 😉
@@FauxHammer you were a big part of inspiring me to get into resin printing. I bought the gktwo today for my sprinter van. It’s going to be a mobile(well ventilated) creator lab. Thank you for making great videos
Oh man, my first comment on UA-cam... feeling all sorts of lame. I watch your videos a lot and value your opinion but I'm curious if you still feel the GKTwo is the best out there with the likes of the UltraCraft Reflex and the Athena on the way. I'm an engineer and have a full maker lab but I'm really interested in a new resin printer but having a bit of analysis paralysis. My biggest issue with the GKTwo is that I can't find any news on an impending wifi module. I really hate using USB keys.
All i can say right now is give me a month. I want to help but I'm still working on a video which is for people with Analysis Paralysis specifically. because It's confusing to me. So I'm trying to condense it down to the top picks by budget.
Also, I know of something coming that will be added to that video which i can't talk about yet.
I resonate with this. Looking forward to this video and thank you in advance! @@FauxHammer
I am thinking of the GKTwo as well. As far as analysis paralysis goes, I set up a pros and cons list for every major purchase I make. I have found the GKTwo checks more of the pro boxes that I'm looking for (particularly the heater and air filter) than cons. Slightly higher price tag/wife finding out, lack of auto-leveling and a network module are definite cons, but the network module is (like Mr. Hammer sorta implied) on its way. I'm waiting on that before purchasing it from the FauxHammer link, of course. 😀
The GKT is a multiplication factor cheaper than the other 2 my guy
So the only issue I have with this is for the low low price $259 You get a 7 l ultrasonic cleaner with a pretty interface and a pretty case but you can go buy ultrasonic cleaners that are 15 l which is a lot more parts and bigger plates you can put in for 150 bucks that are heated. Now if you're heating alcohol I guess you run the risk of having combustion because now you're raising a temperature even more but I can tell you cheaper than that but not much You can get a much bigger unit I know a place where you can get a 30 l for $285 and that's a lot of big parts for machines like the Mega 8K The Jupiter and some of these other new ones that are coming out. It is nice that it has a place you can put the build plate but it's designed for their printer which is not that abnormal so now you've got a machine that works great if you have that printer. Happy spring a little bit more say about 300 and some change 305 325 You can get a dual frequency cleaner it's 28 and 40 khz and that inherently could be a little better depending on what you need I don't think you need the dual frequency but in theory 28 kilohertz will help get different areas based on how the resin is working. It's nice product but I mean other than the lid ceiling better than the units you buy that are you know industrial I don't see the value of it over a much cheaper option
Got any links to the ones you like?
@@ubernoob458 but I would recommend replacing the mains inside the unit, may not be necessary but in my experience they are not great
It seems the washing thing emits alot of tvoc if used with ipa, the seal is not particularily effective
Comment for Al
Comment for the algorithm ;-)
hmmm.....that wash station would make cleaning the airbrushes a lot easier as well..... edit: oh, and here, have a 'Comment' for the algorithm as well
I really love what I have seen of their products in your reviews. Unfortunately I must go much cheaper....sad face lol Love their stuff but way too high priced for my lowly budget.
that's totally ok. what is your budget, there is a great printer for any budget $100 up
I am hoping to get money for Christmas lol. I am 53 yrs old and on dissability. Been fighting cancer for 23yrs. I am hoping to be able to shoot for the $300 range. May have to save money for a while but hope to get part for christmas. right now doing lots of studying@@FauxHammer
I will only be able to get one printer because of my finances so I'm hoping for 8k lg build plate something like the Saturn 8k@@FauxHammer
@@butchsbasementbuilds6828 That's a great printer!
It seems like a lot of printer for the money. Right up my ally lol. Been learning a lot from your channel. Really helping me figure things out. I like to study things before I get into them and it's always helpful to be able to find a channel like yours to help with that. Keep up the great work.@@FauxHammer
yeh i think people claiming the IPA combusts comes from like a single user hearing something from a friend that heard it from a friend who heard it from a friend and so forth to the point all context was lost and they probably were not even using IPA to begin with. I mean this is fairly typical of internet myths like this.
I’m a bit stumped. I currently use the pickle jar cleaning method - which is messy and probably not good for my health. I’m looking to invest in a good automated cleaning station to get rid of all that. However here you state that this system works best only after you’ve first cleaned your prints in a pickle jar! WTF?!
yeah, that... literally what I said.
You can clean in just one device/container but that will contaminate the whole container.
What i actually do now, is...
Wear a filtered mask.
Rinse model in one pickle jar
remove and rinse in another pickle jar.
Wash in this Ultrasonic cleaner.
remove and leave to fully air dry
Cure.
By using multiple stages, my first pickle jar is the only one I need to regularly empty, then the second jar less frequently. my ultrasonic cleaner has not had a liquid change in over 18 months, but I also use Methys, not isopropanol becasue ISO turns clumpy where methys does not.
@@FauxHammer Thanks. This then begs the question, have you used any cleaning station that does do a better job than the trusty pickle jar approach?
@@Perchpole yeah, this one...
The pickle jar does only does so much. the ultrasonic will eat into all of the surface level liquid resin and strip it off given enough time. Inside and out of the model too, assuming it's hollowed.
So why not just buy an ultrasonic cleaner for a fraction of the price.
Comment for the algorithm
I don't know why you'd drop money on this when Phrozen has an ultrasonic cleaner for only 44% of the price of this one.
I only see a need for these things if you are printing en masse. Occasional prints, nah.
3:00 I wouldn't be doing this. You're better off buying some beakers or other containers and put your model and IPA in them. The bath itself should be filled with demiwater.
comment for you
always appreciated
I emailed Uniformation and was advised that the ultrasonic cleaner had only one transducer and is "mainly designed to use IPA or alcohol as a solvent, so the cleaning power is relatively small". Normally you would expect 3 transducers in a 6L tank and it may be that the W320 has lower than the usual 40KHz ones. Bottom line is, it's not so good for normal cleaning tasks if you were thinking it may be. I got a dual frequency 28/40KHz unit instead and if I use IPA/meths I will put it and the model in a zip lock bag as advised elsewhere in these comments.
That makes sense. I probably should have asked them myself by now
Comment :)
thanks so much
There is not enough oxygen under the vat to combust the alcohol, its like trying ro light gasoline with a match allready submerged, it wont has a self sustaining combustible cycle.
That what I thought, the main worry people had was this letting off combustible gas when you open it
I got my wash and cure station today and the cure station has no turn table. Emailed the company, no answer. Kinda useless with out it. I guess I'll have to send the whole thing back just because of that simple plastic part. The joke of it all is that on top was a sticker says QA passed. I guess they just toss them stickers in the boxes without really inspecting it. Pretty obvious. Stupid workers.
Comment
Appreciated
Jeeze they really did think of it all.....amirite
they are not dumb.
Ultrasonic cleaners are great for cleaning eye glasses, use it monthly to do, as do opticians.
Just as a warning, this is EXTREMELY dangerous. An actual fireball witing to happen. You should never use flammable solvents in an ultrasonic cleaner. The fact that this company has put this product on the market is horrifingly irresposnible.
Just keep the lid closed while it’s running. Don’t have an open flame near the machine when you open the lid. Crisis averted.
I use this cleaner and have done for a couple of months now with methalyted spirits and it's absolutely incredible, I'm unsure why this hobby has so many people worrying constantly about other people constantly screeching about basic safety standards. Please just focus on yourself as I will focus on myself
Bwahaha
.
comment for the algorithm
who TF is putting ANY print into a wash station for 20-30 MINUTES?!?!
I really would love to get this with the G2 printer but it's quite an investment I just can't justify right now
Comment for the algorithm
the algorithmis happy.
Comment
Thanks