I had to remove the entire dash to replace the AC evaporator. Problem is when I put it back together, the area where the light sensor is has the clip to secure the dash to the firewall. Apparently I missed and the dash rattles big time. Your video did great detail on how to remove the cover. I will address the rattle knowing exactly how to remove the dash pad. Great video (this from an EX GM mechanic)
I am going to use your video to attempt to put a new heater core in thru access of the top. This is not proper, but it will save my AC charge, plus days of labor. If I have to do some cutting to help removal, It will all be covered back up with all the top trim parts. I did a similar thing with a ford Taurus, and it shortened the nightmare by tens of hours. Thanks Froggy for getting me pointed in the right direction! You may have saved me thousands!
Thank you for sharing this!!. I'm trying to replace the daytime running light sensor in the top of my dash board cover and wasn't sure about the removal of the a/c vents, the grab handle and the pillar caps until I found your video....Again Thanks !!
How did it go Scott? Did you decided to remove the dashboard yourself? The airbag and the sensor are my concerns. I am going to try the (do it myself way) this week.
Very good Mr , thank you will replace my dash this week end very good video again thank you for your time in making this video for all of us to learn from
Very good explanation, it will help me a lot, I have a short yukon 2001, when I turn on my truck, smoke starts to come out of the vents above the dashboard.
Did you happen to notice if removing the dash cover gave better access to the Mode Actuator? I'm having a terrible time getting the rotating control plate back in. Mine came out with the old motor and I thought for awhile that they were glued together. But it turned out just to be a very tight fit. Tomorrow, I'm going to start taking the dash apart because I'm not able to put this pate back in from below.
Great video again Froggy! Looks like the oil pressure gauge is indicating pressure with the vehicle off so is you next job a oil pressure sending unit/sensor replacement? :)
Again, great video. I did the job using your tips. My dash was very weak and brittle and broke to pieces without the possibility of repair. I cannot find it anywhere. Do you know of any place where I can buy it?
I had to remove the entire dash to replace the AC evaporator. Problem is when I put it back together, the area where the light sensor is has the clip to secure the dash to the firewall. Apparently I missed and the dash rattles big time. Your video did great detail on how to remove the cover. I will address the rattle knowing exactly how to remove the dash pad.
Great video (this from an EX GM mechanic)
Glad you tackled it!
This is a very very very helpful video. Thanks for taking the time to make it public.
welcome.
:)
I am going to use your video to attempt to put a new heater core in thru access of the top. This is not proper, but it will save my AC charge, plus days of labor. If I have to do some cutting to help removal, It will all be covered back up with all the top trim parts. I did a similar thing with a ford Taurus, and it shortened the nightmare by tens of hours. Thanks Froggy for getting me pointed in the right direction! You may have saved me thousands!
Post back how it goes.
:)
Please post how it goes.
:)
Thank you for sharing this!!. I'm trying to replace the daytime running light sensor in the top of my dash board cover and wasn't sure about the removal of the a/c vents, the grab handle and the pillar caps until I found your video....Again Thanks !!
That should be pretty easy now, thanks for viewing.
:)
oh man, you have safe me a lot of time!!! Thank you!!
Your video was very helpful. I am still debating, but now I can reasonably get it done.
Great.
:)
How did it go Scott? Did you decided to remove the dashboard yourself? The airbag and the sensor are my concerns. I am going to try the (do it myself way) this week.
Very good Mr , thank you will replace my dash this week end very good video again thank you for your time in making this video for all of us to learn from
Awesome. Thanks for putting the effort into making this!
Thank you for the video! Now I can change the inside/outside door actuator with ease!
Door actuator? Dash? Please elaborate. Oh, you mean the grab handle? Passenger assist? Yeah.
Next time just disconnect the battery to avoid any issues with the airbag going off.
But great video thank you
Thanks for viewing. FWIW I hate airbags, wish they were never invented/mandated.
:)
Thanks Gian! Good point !
Very good description. I have some burned wires in my dash saves me from having to be a contortionist to get to them!
Glad to help.
:)
Very good explanation, it will help me a lot, I have a short yukon 2001, when I turn on my truck, smoke starts to come out of the vents above the dashboard.
Good video ,really helped on the dash handle it was giving me trouble till it mentioned the white clips
Me too the first time.
:)
Great vid...saved me $1100 on my 2001 Yukon XL! Thank you for the help!
Glad to help.
:)
Thanks this helps for my 2002 Avalanche! Two thumbs up!
Glad to help.
:)
Big help just knowing what to expect, thanks!
Thanks for the help
Thanks I couldn't figure out the hand grab above the passenger side airbag on my '00 suburban.
Glad I found your video you saved me a ton of time!
👍👍
Did you happen to notice if removing the dash cover gave better access to the Mode Actuator? I'm having a terrible time getting the rotating control plate back in. Mine came out with the old motor and I thought for awhile that they were glued together. But it turned out just to be a very tight fit. Tomorrow, I'm going to start taking the dash apart because I'm not able to put this pate back in from below.
Sorry I don't, I did it as 2 separate jobs.
:)
Thanks a lot. That looked pretty easy.
thanks for the video very helpful thanks again.
Welcome.
:)
That spot above the passenger side air bag, I'm having a hell of a time getting that to break loose
Nvm i got it!
Very helpful video.
Great video again Froggy! Looks like the oil pressure gauge is indicating pressure with the vehicle off so is you next job a oil pressure sending unit/sensor replacement? :)
Hmm, never noticed that, I will ck.
:)
Thanks Froggy! Great video.
Glad to help.
:)
Froggy, does apply for a 2004 Chevy avalanche as well?
In general yes, but certainly there are minor exceptions, just work slow & careful. :)
Thanks man, you save me time and money.👍
I love doing it. Spread the word.
:)
Again, great video. I did the job using your tips. My dash was very weak and brittle and broke to pieces without the possibility of repair. I cannot find it anywhere. Do you know of any place where I can buy it?
Look for a low miles junk yard dash.
They can be painted as needed.
So was it necessary to remove the airbag fuse.
I did not.
Thanks for the great video
No problem.
Very good sir thanks I need to replace my dash from my 02 tahoe
Good luck, check back in with me.
:)
Nice video. Thanks a lot!
Thank You thank You thank you
Its gonna be same work for 99 tahoe?? I need replace. Just the top of dash
Well, similar, but I doubt it's exact.
:)
Could u help me out my tahoe throws cold ac when day is fresh already added Freon and charge cabin filters but when day is hot ac is kinda hot too plz
If adding CORRECT Freon kind/amount does not work, it's beyond me trying to diagnose over the YT channel. Sorry.
:)
how much would i have to modify to fit a dashboard from an 04 to my 93 2 door tahoe
Sorry no idea.
:)
Great video thanks
Welcome!
thanks my friend u just made my day
Glad to help.
:)
Thank you it was a big help
Glad to help.
:)
Great video! Thanks!
Thanks for viewing!
:)
You gotta work it work it you gotta...
Great, patient. Good Video !!
Thank you for viewing.
:)
Thanks bro
Welcome!
How can I remove those clips off the first part you took off
Not sure, long time ago. :)
Hey what's up did you ever make video part 2 so you can see how to get to it
It's all there look again at other videos.
Thanks for the post!
Good video bro
I don’t have that white release button how else can I get it off?
Where in the video? Thanks. Give me the mm:ss
Thanku so much sir
Glad to help!
@@1947froggy yea
Very helpful
Thanks.
:)
AWESOME !!
Thank you.
Glad to help.
:)
It took you 10 mins talking about the work when the job takes 3-4 mins tomorrow to get the front screws out after the bezels.
Hi Tommy, yes I talk as I work, maybe you should try the videos with no audio. Thanks for viewing. :)
Thanks sir
Welcome.
:)
VERY HELP FULL
could be done better vid wise. but helped tons
Thanks for the video
Welcome!