These things are restricted. Do some research and open up the muffler. Get a carb adjustment set. Pull the carb and get rid of the limiters. That saw will need adjusted sooner or later. Use 40:1 mix. Chainsaws require a lot of maintenance, so if you do all of that then it should last for your firewood needs. In the off season it is good to start and run your saw periodically to keep it loosened up.
Nice! Keep goin dude! You got this! Your channels gonna blow up if you keep it up. Looking forward to the head to head vids. Stay healthy bro. Subbed! #166! Let’s go 1000 subscribers! 👍
I have basically the same chainsaw but mine's called the X-Bull it had a 20-in 18 inch bar a little cheaper I didn't need to have as big as bar cost like $140 62 cc's and that was back in 2020 still works just fine very nice power been reliable to me and I have another one of the backup because they're so cheap about two but I haven't needed to open the other box yet for a chainsaw I just want something that does the job and it's been doing that reliably
That is a Zenoah Clone Saw. 99% Chance its not 62cc. They usually use the 54.5cc (58cc) cylinder on it. I've bought 2 different 62cc clones and both with 54 5 actual cc. The 62cc does exist but you're more likely to get the smaller cylinder. If you pull the cylinder and measure the piston, if it's 45.2mm is the 54.5cc. If it is 48mn then it's the 61 5 (62)cc.
You're lucky you didn't smoke the clutch doing the plunge cut. They tend to slip when you really push them. If you upgrade the intake by the cylinder to the "5200 Performance intake" (requires hogging out the white plastic separator) and a 372xp carb, the extra revs it allows keeps the clutch from slipping so much. The clutch and the chain brake are the weak points on the saw.
Fyi pumping the throttle does nothing. The old cars with carbs and acceleration pumps used that method. GOOD VIDEO, Thanks
THIS LOOKS JUST LIKE MY SALEM MASTER 5820F
If i get a China saw I always get a Holzfforma and nothing else. I know I can find parts if needed to today or 5 years from now Local or on the Net!
All these Chinese clones are based on the Zenoah G5200. These are old design saws and must use 25:1 oil fuel mix not 50:1, 40:1.
These things are restricted. Do some research and open up the muffler. Get a carb adjustment set. Pull the carb and get rid of the limiters. That saw will need adjusted sooner or later. Use 40:1 mix. Chainsaws require a lot of maintenance, so if you do all of that then it should last for your firewood needs. In the off season it is good to start and run your saw periodically to keep it loosened up.
looking forward to the comparison...thumbs up !!
Thank you! That video is coming soon!
Oke bro keren mesin nya
Nice! Keep goin dude! You got this! Your channels gonna blow up if you keep it up.
Looking forward to the head to head vids. Stay healthy bro. Subbed! #166! Let’s go 1000 subscribers! 👍
Thank you I appreciate the support !
I have basically the same chainsaw but mine's called the X-Bull it had a 20-in 18 inch bar a little cheaper I didn't need to have as big as bar cost like $140 62 cc's and that was back in 2020 still works just fine very nice power been reliable to me and I have another one of the backup because they're so cheap about two but I haven't needed to open the other box yet for a chainsaw I just want something that does the job and it's been doing that reliably
Not bad rings not broken in 👍😊
That is a Zenoah Clone Saw. 99% Chance its not 62cc. They usually use the 54.5cc (58cc) cylinder on it. I've bought 2 different 62cc clones and both with 54 5 actual cc. The 62cc does exist but you're more likely to get the smaller cylinder. If you pull the cylinder and measure the piston, if it's 45.2mm is the 54.5cc. If it is 48mn then it's the 61 5 (62)cc.
And yes it's the same as the Wemars, Coocheer, "Professional Chainsaw", Auto jayer, Xbull, and many others.
You're lucky you didn't smoke the clutch doing the plunge cut. They tend to slip when you really push them. If you upgrade the intake by the cylinder to the "5200 Performance intake" (requires hogging out the white plastic separator) and a 372xp carb, the extra revs it allows keeps the clutch from slipping so much. The clutch and the chain brake are the weak points on the saw.
I have videos on my UA-cam channel (they are a touch crappy, but too broke to afford a tripod right now) but you can easily tell the difference.
Yah I wasn’t sure if the clutch was going to take it. I was impressed it did lol. It’s a stronger saw than I expected.
@@Justdubbin Should check out the after video. That saw is a beast. 192 PSI compression 14k free Rev about 12.5k in the wood.
Air filter and other replacement parts ???? Reason I’m sticking with poulan period
I think theses china saws are great vehicles emergency saws and that’s it 😮
Without parts there a problem 😢
walmarts lawn equipment has really gone from solid low quality to straight low quality crap garbage
Anything MTD sucks weiners
Yep