Let me see if i can get it together....lol. basically, the teflon mod is.... a piece of white plummers tape, little less then an inch... wrapped tightly and clean, around the barrel and the end of the bucking, (in between),just enough, to let you close your hop up chamber fully,without a gap. dont cover up the part where your pressurearm pushes the tounge down☝🏾 what it does? it puts pressure around the bucking and inner....keeping the bucking from lifting around the barrel,when your nozzle dives into the bucking and the shot is beeing released. pressure cant escape and you have a more consistent shot... you want ALL the pressure from the gas to go where its supposed to go😉 i suggest to get a crazy jet maple leaf hop hop chamber/innerbarrel kit...6.04mm. green 50° or yellow 60° shore. best budget upgrade since sliced bread. add the teflon tape mod and you are good to go....👍🏾
@@broadside8326 hmm…I’ll need to check that out. I’m a bit skeptical and afraid this could cause any stress, something to be uneven or misaligned. 🤔 but I’m still open to suggestions
...dont worry😌 its an easy and effective mod when you want to really eliminate possible airleaks in your system. barrel/bucking.... bucking/nozzle... nozzle/pistonhead... nozzle gas opening to gas router. have you tried the purple laylax gasrouters yet? 👍🏾
the normal 70° is a little too firm for my liking...something in the rubber composition makes the oils/silicone turn brownish after time. 50° or in fps raised pistols a 60°.... check their 2021 silicone buckings decepticon/autobot....awesome little things👌🏾 ...and yeah...thank god for teflon tape😄 good video👍🏾
Nice deskriptiv video ass always. Just got my first TM 4.3 (ops tactical .45), and i need to change the bucking so nice guide. It had a nineball purple bucking in but I didn't know how riped it was now i do. 🤣😂
I've got a similar bucking and everything but I find that the bucking expands the hop up chamber to the point where it doesn't fit into the outer barrel assembly. Any tips on how to shrink the bucking so it fits more flush?
Meltedchair513 Not sure how to answer this one. Hope you find the answer soon! Was almost going to recommend doing the Teflon tape mod but I don’t know the full extent of your issue
Thanks for watching! Change the bucking out when the OEM one wears out. Most people change it out when they’re adding mods. I changed mind because the OEM bucking wasn’t holding the BBs any longer
@@airsoftmechanic Well put on some nail polish and raise your voice a little! Everyone will think you're some hot chic and you'll end up with more subscribers!!! 😉That's way better than wearing Mechanix gloves to work on a airsoft gun
@@SololaneMvlog Geesh, what was I thinking!?!?!? But at the same time, not sure being able to take apart a toy gun, qualifies one as, being a "mechanic"....
I’m being told it’s recommended to add teflon tape after posting this video…clearly there’s something I’m missing here. What is the teflon tape for?
Let me see if i can get it together....lol.
basically,
the teflon mod is....
a piece of white plummers tape,
little less then an inch...
wrapped tightly and clean,
around the barrel and the end of the bucking,
(in between),just enough, to let you close your hop up chamber fully,without a gap.
dont cover up the part where your pressurearm pushes the tounge down☝🏾
what it does?
it puts pressure around the bucking and inner....keeping the bucking from lifting around the barrel,when your nozzle dives into the bucking and the shot is beeing released.
pressure cant escape and you have a more consistent shot...
you want ALL the pressure from the gas to go where its supposed to go😉
i suggest to get a crazy jet maple leaf hop hop chamber/innerbarrel kit...6.04mm.
green 50° or yellow 60° shore.
best budget upgrade since sliced bread.
add the teflon tape mod and you are good to go....👍🏾
@@broadside8326 hmm…I’ll need to check that out. I’m a bit skeptical and afraid this could cause any stress, something to be uneven or misaligned. 🤔 but I’m still open to suggestions
...dont worry😌
its an easy and effective mod when you want to really eliminate possible airleaks in your system.
barrel/bucking....
bucking/nozzle...
nozzle/pistonhead...
nozzle gas opening to gas router.
have you tried the purple laylax gasrouters yet?
👍🏾
@@broadside8326 Yes I have them for my TM G17 mags
@@airsoftmechanic 😌👍🏾
Great tutorial. Thank you very much 😃👍
Thanks for watching!
So useful man keep up the good vids 👍
you should install maple leaf i-key also
You should add some Teflon tape
the normal 70° is a little too firm for my liking...something in the rubber composition makes the oils/silicone turn brownish after time.
50° or in fps raised pistols a 60°....
check their 2021 silicone buckings decepticon/autobot....awesome little things👌🏾
...and yeah...thank god for teflon tape😄
good video👍🏾
What bbs on 50 degree
thanks man. Helped me a lot.😊
Nice deskriptiv video ass always. Just got my first TM 4.3 (ops tactical .45), and i need to change the bucking so nice guide. It had a nineball purple bucking in but I didn't know how riped it was now i do. 🤣😂
ik im late but is it possible to only upgrade the bucking and keep the barrel stock on my tm hi capa 5.1?
josh krouse Yes absolutely
@@airsoftmechanic Thank you!
I've got a similar bucking and everything but I find that the bucking expands the hop up chamber to the point where it doesn't fit into the outer barrel assembly. Any tips on how to shrink the bucking so it fits more flush?
Meltedchair513 Not sure how to answer this one. Hope you find the answer soon! Was almost going to recommend doing the Teflon tape mod but I don’t know the full extent of your issue
Nice vid sir very straightforward.. watching from the Philippines....sir when to tell if i need to replace the hop up rubber?
Thanks for watching!
Change the bucking out when the OEM one wears out. Most people change it out when they’re adding mods.
I changed mind because the OEM bucking wasn’t holding the BBs any longer
Does this fit the newer versions of WE Hi Capas? Specifically the 5.1R Hi Capa. If you do reply, thank you very much.
Seeing that it’s a TM clone, I would say yes
@@airsoftmechanic Thank you very much good sir
Autobot ❤
Can u do vid on adding Teflon tape?
can i use it in aap01?
I believe it should work with the AAP-01
thank you
Thank you for sharing your knowledge...specially the difference between the types of buckings....
Are your hands really that tender and sensitive that you need to wear Mechanix gloves??????
TJ K Are you really that bored that you had to ask why I wear gloves??????
To answer your question, no. My hands look feminine at certain angles 🥲
@@airsoftmechanic Well put on some nail polish and raise your voice a little! Everyone will think you're some hot chic and you'll end up with more subscribers!!! 😉That's way better than wearing Mechanix gloves to work on a airsoft gun
well....he is a Airsoft Mechanic sooooo........ ok i'm out :) :) :)
@@SololaneMvlog Geesh, what was I thinking!?!?!? But at the same time, not sure being able to take apart a toy gun, qualifies one as, being a "mechanic"....