Відео

The music choice gave me PTSD

Do you have any videos revving it with just the midpipe and stock exhaust?

Just built one with the same upper no BCG & CH. Got a Daniel defense BCG & a Radian CH. Geissele SSA trigger and a PSA AR-15 Complete Classic Shockwave Pistol lower ODG. $900 ish

Great review my friend 💯💯💯

Great review my friend 💯💯💯

Great video, my project for tomorrow!

Give us an update and codes activated. How much more hp? What do you like and not like.. i have the same build rn.

How much amo dose that guy have that kept shooting

Nice

No way this guy said 5 50 6. It's five five six

H2 buffer and adjustable gas block. Thank me later!!

I just installed mine and getting a check engine light, vsc light and trac light on

Bad news for 😢 and my beloved 07 4runner which goes my the name Reus. I lifted her up yesterday on a 4 post lifted and had a mechanic check it with a camera cable device. We fish the cable up between the bell Housing and engine after moving the clip and saw some oil on the rear main seal😢. SUCKS MAN sucks

Where did you get the oil pan gasket and what's the part #?

Nice build! Unfortunately that same charging handle was chewing up it's retaining notch on my upper. Had to replace it.

I changed mlok to quad, upgraded trigger to rise armament, & I made it my main squeeze plus was good price before upgrade

I was looking at their 11.5 commando clone. I never owned an AR pistol so it was a huge sign of relief when you clarified about shouldering an arm brace.

This is my main home defense with mcarbo red dot mount and mcarbo flat faced trigger . Makes it feel like mp5 . Such great home defense gun with Glock mags in 9mm

I just bought the gen1 looking forward to taking it out

How long was the holes? Did you guys measure it?

looks like the brace is cracked, what's up with that?

Also V8 models with the tow package have the transmission cooler. I have never towed with my 4Runner but I can imagine the cooler fluid helps improve reliability.

This guy also giving very bad misinformation on replacing door handles I believe. I did same thing on my 4Runner following some other Toyota wannabe and ended up having to remove my door trim panel after finding out there was a step missing. Unfortunately with used cars, brittle 1:21 1:21 plastic clips and automatic door cable plastic parts do not always last and break after one or a few times of being removed. Point being, I had to buy another used door panel because of misinformation and it costs a lot. I watched the Toyota Sienna door handle replacement videos from knowledgeable UA-camrs and was finally able to put this left side door back to working condition. Step missing: get a medium/thick flexible wire and make a U-sized look. Before you insert the door handle rear side into the outside door frame, there is a metal latch that you need to pull back (spring tension), right near that insert area. Put the looped wire around this latch to pull it back. Push the new door handle rear side into so the latch is still pulled back by the wire loop and when the door handle is gently pushed in all the way, pull on one side of the loop wire to slip it out of the door. The push you door handle latch the rest of the way in. Insert the door lock mechanism and tighten it (I lost that small set screw dow the bottom of the door frame multiple times, might want to stock something under to catch the set screw. Finally, pull the door handle (opening the door), and it should return to its base position (spring mechanism). This is the proper way. I hope every 4Runner enthusiast reads this and don’t end up like me spending hundreds due to misinformation. 😅

Where you going the chrome clamps and braded holes from on the catch can?

How much did you pay for this?

I race

Greetings from Arkansas Bryans 🔥

Yeayup

Yeah buddy

Transmission fluid is the one thing I never use non-Toyota fluid for. My 4th gen uses T-IV fluid and the local dealership charges about $7/quart, only 3 quarts for drain and fill. Not expensive, especially compared to repairs. Also would only get them from the dealership since counterfeits are numerous.

I got this but only cig lighter socket works, the one with the lid doesn’t,…. Do you know if there’s a fuse I need to add or look for?

Is this good for indoor games?

For high mileage transmissions, it is advised to NEVER do a Full Flush. Only Drain and fill it. Great video!

I am seeing the same issue on my 4runner but I don't want to believe it's the rear main seal.

When you move the clip at the bottom of the transmission, did you see any oil running down.

@Airsoftmechanic did you notice any slipping?

Cheaper doesn't meen its bad at all we have all figured that out with the hi point carbines

Excellent video, thank you!😊

Which brand aftermarket filter and gasket you went with?

I wish you can have a well detailed video without the soo part music and how come you didn't put a metal thermostat housing why kept plastic housing?

*** To add 2 more round capacity to the 17 round magazine (9mm), you need to go from 10 coil spring to 11 coil spring.

My name Jeff

Wooooohooo

If it goes bang all the time, that’s all that matters. I’ve learned a lot of companies get PSA to manufacture for them and rebrand it as their own.

How did you get rid of the p0420 codes

You must not live in a salt belt, cause the underneath of your forerunner is so clean. The frame is clean. I see no rust.

Hi! This legal 11.5 barrel for ar pistol? Plan to buy here at virginia please let me know.

Glad to see someone made a video reviewing these JBA headers! Bought mine recently, along with an 18” magnaflow muffler & aero exhaust 3.5” resonator. Stoked to get these installed!! The end result sounds great

I'm trying to find a replacement for the exact tray you took out of your 4Runner haha. Do you still have your old one or at least know the name of that particular version of the tray? All I can find are the smoker versions for sale. Thanks!

I got the 4.7L V8. Threw some Doug thorley shorty headers on with high flow cats and Borla muffler. Next is cold air intake