Відео

Just spend the 40 bucks and enjoy for another 20 years..

It would’ve been great if you had showed every step instead of cutting scenes because I have no idea how you even got that spring out.

Think you cooked the gasket when heating, Probably why it was loose after first bolt out

Great information thanks !

Did you convert this from 2 6v batteries to 1 12v battery?

Thanks for showing the whole process. I have a HUGE farmers wraparound porch that could use a coat or two of this product. Good job!

Is that a fe35 or to35

Oil analysis will tell you about fuel dilution and coolant leaks. Blackstone labs is a good one. 58 USD with TBN. New temp probes too.

Heat the bolts up with a torch once bolt turns spray wd 40 will come right out.

I put a little stronger bolts and put some antiseize.

Hey Chris, I’m not sure you check comments anymore, but we’re cousins! Your videos brought back a lot of memories.

I just did a 20 year old deck that I was told needed to be redone with this. It looks great. I will be happy f I can just get a few more years out of it due to the price of lumber!

What a stupid unwatchable video

If your 6.7 ram is loosing a bit of coolant and is starting to have emissions codes, your EGR cooler is probably failing. Replacing the DPF and not replacing a leaking cooler will result in replacing the DPF again, along with a few sensors.

I’m a mechanic who was quoted 2400$ to re-core a radiator for my Clark 664 skidder, which was totally absurd considering the core is in great condition. All I needed was the top pan, a drain valve and one mounting bracket re-soldered. Your video and the knowledge you have learned from your neighbour is a godsend. You’ve given me the confidence to attempt this repair. Thank you sir! 😊

PB blaster not wd40. Use anti seize on the new one

Delete it.

I'm kind of new with the 479 I'm having trouble with mine seems like it's digging into the ground too much getting dirt on top of the sickles and do you not have to run these at the higher RPM I'm running around 1600 RPMs maybe I should slow it down

please, I have a question, can we mount this engine on a ferguson tef20 4 cylinders, my second question is can we mount a cylinder head from a ferguson tef20 on the engine block of this engine . thanks in advance

Do you think the deck correct would be a better choice for the railing? Despite cost. My railing is in quite rough shape as well

We need a video of how to get to that piece. I can’t remove the smaller pins.

It's a film forming coating with minimal solid stain properties in it. It's a masking product with high failure rates. It doesn't Bond without professional cleaning, and the second coat doesn't even bond to itself. It's a last resort lipstick job before early failure. DIY waste of time and money. Just like Behr Deck over and Rust-Oleum restore a deck.

How hard was it to remove? I have to drop mine to fix those bolt snapping

For the secondary canister. Could i mount both vortex chamber and vapor catch can for lack of better words next to each other and weld a small hose barb for the vapors to go from the vortex to the catch can/over flow? I'm curious as to what happens to the vapor in the vortex can...I'd imagine eventually the pressure needs to bleed off or? Is that what the radiator cap is for on top?...

The fan is still working well. If the light fails I think it becomes disposable. Again it should be 1k-1.5k lumens. I did have a problem with the plug inside it losing continuity. While geeks say don't mess with a plug, I made the contacts tighter- on for a few more years.

Good luck finding the led puck.

at about 6:04 you point out one of the rings is most important. but you do not indicate which position it is. there are 3 on that piece

You measured from your axle stub..not your balljoint

Awesome slow and easy wins the race

I let truck idle spray it wd40 while hot loose up right away dipp it on hot water let it clean and with toothbrush clean it got rid of the 5mph service see dealer

I have a dodge ram pickup same problems from what I see dodge has the most problem of all the pickups and they have recall on these pickups but they don't get the problem fixed tks

FYI. There is a spring right inside of where you “heated” it. That spring is most likely toast.

Great video just what I was looking for.thanks 👌

Would you have a video how to remove the trigger?

Very good and informative video, thank you

I’m trying to do this on my ls3. Does it matter if the exit hose on the pot is below the radiator inlet. And should the cap of the pit be the highest point of the cooling system

Those chunks are the actual filter 😮

Wait till you have to replace the boards. Trying to un screw the screws is going to be tough!

Same model I am ordering parts tomorrow and will repair using your help thanks for the video now to find parts

good video ive been replacing o rings on a hitachi nr 90 ae. trigger assembly i didint see any repair video on this gun anyway i still havent got it right

Very helpful, thanks

I couldn't make it more than 2 minutes with that annoying speed up.

Then you for the video and showing the post number to this starter The official db website is maintained by leftists... I couldn't find it... Still have the rig???

Is there a granular texture or is it pretty smooth?

I think gravel or dirt is better than concrete for adjusting toe in. The softer gravel let's the tires rotate without grabbing the way they would on concrete. Alignment jigs have rotary platforms for the tires for that reason.

O finally abandoned this relic and moved to a Heston.

Can you put Deck Correct over scrapped and sanded paint?

Thank you for taking the time to make the video...helped a bunch.

What color is that?

KROIL WORKS