Відео

Thank you so much for this video, it saved us lots of money. You are awesome

Thank you Much! that is super helpful!. as a suggestion if you can add the link where to get it it will be better.

WOW, that was really quick & cheap. Im having trouble unscrewing the screw. Tried 2 sizes of Phillips, both slipping.. Shining the flashlight, i can't tell if its a square or hexagon shape. It's a Fridgedaire Electrolux FG HB2869TF3. I'm thinking the Return Spring may have come loose. It just flops. Doesn't catch anymore. I cleaned any sticky off the exterior but, my photos indicate there might be some sticky soda up inside there. Can barely see a Spring in the photo. I couldnt get my head or eyeballs in there, to look, so i used the camera w/Light. Any suggestions?

📢 But don't be smoking 🚬 in that bathroom 🚽 when it's full of those acid fumes ... 💥 !!! 😉

I followed your instructions. They worked like charm. Thank you for sharing the knowledge.

*You dont need the acid - I used a combination of bleach, bit of dish soap and vinegar, worked exactly the same and didnt need the saran wrap or plastic baggie*

ACID NOW $10 BUT WORKS GOOD

Works

Ty frankie

Theres no reason to take it apart to replace the lever it just pops into place

This just happened to me today. Thank you for your video.

I just replaced the middle piece. The part with teeth. It cost around $ 10. New pulsator is around $ 150. Knock offs are around $ 80. It was a pain to remove and even bigger pain to put the new one in. There are clips on UA-cam on how to do this.

Where did you buy the replacement dispenser?

My wife told me last night there was a problem with the washer, I checked it out and then saw your video and ordered a new agitator. It will be in Saturday, and it's a 5 minute fix.. Thank God.

READ BELOW

Very important things missing or changed. 1. Have mildew house ready. When you pull that, you will see mold, black mold. No kidding. Now is time to clean that area. 2. Changing the actuator paddle, metal top. There is now 4 tabs on the back you have to bend out before swapping. Bend back in after swapping. 3. Inserting the paddle, a small spring is included and necessary, don't lose it. The spring allow the actuator to return to off position after pressing and will fall off if not careful. It goes on the big side. Took me three tries to get it correct. If incorrect water ice keeps running, self explanatory. Good look.

Was the plastic wrap just to keep the fumes contained?

Thank you man, it worked great!!! I like the seran wrap covering the toilet. thank you again.

tightening the middle screw is easy but not really effective as it will loosen very quickly if the agitator gears are worn already

It works. This is the best solution you'll ever find. Thanks brother.

2024 still relevant!

My screw broke inside how do I take that piece off

Thank you!!!!

Awesome 😊

Great video! Very helpful!

0:33 SIX

THANK YOU SO MUCH! My husband followed your directions and it worked completely. We saved a LOT of money because we had a call in to the plumber and we were able to cancel it.

It's woulDn't, not wunt, and shoulDn't, not shunt. MuriAtic, not muriOtic acid.

It's woulDn't, not wunt, and should n't

My agitator bolt Snapped off.

Thank you!! Awesome explanation!

Someone tell me where to buy this bottle of water and what is its name?

Heck of a smart idea. Thank you.

The bolt is 10mm . From experience put some thread lock (Loctite) before tightening. Snug the bolt down using only a 1/4 drive 10mm & ratchet

I found a easier and safer way to get the panel to come out without excessive force. Using a flat thin blade putty knife , start on the lower right side and work the blade in about 1/8'" . it will release the locking tab and the pane will move out slightly. Work around the pane, top right, two on the top edges of the panel. By the time you get to the left side it should almost pop loose. No yanking or straining and the locks aren't damaged. Now you can release the wire harness and work on the panel comfortably. The return spring is tricky, but only fits on one way.

This solution still works., four years later. Finding the part number was a pain. I finally came back to this site and found the p/n in the comments. Samsung is no help. They want you to buy the entire control panel. You have to make sure the spring is properly installed or it will drip water or discharge ice. The spring holds the lever out away from the control switch so the proper installation essential.

Did you replace the entire wheel?

Those muriatic acid can attack your lungs, wear a gas masks. another alternative is just use a metal wire 1/16 to 1/8' dia, bend the end about 90 degree 1" length hook and poke those rim jet will do the same results. or better. use Mirror to look on the location of the jet, poke it with wire.

A kid tried to flush a plastic spoon. The spoon would catch toilet paper and then it would not fully flush. Had to take the toilet out and turn it upside down. In a few days the toilet paper dried out and the spoon and paper fell out. Re-installed the toilet and it worked fine.

Thank you. I just had to tighten my screw. ❤

baking soda will neutralize the acid. dump a box of baking soda into the toilet and let it sit until it stops bubbling then flush many times.

This was so helpful. Thank you so much.

Tried this as a last resort, worked like a charm! Thanks! I agree with the others who recommend wearing goggles when handling strong acid

Thank you so much.

The panel will not budge. Seems to be stuck even though the screw has been removed. Any suggestions?

Does the muriatic acid do any damage to where its placed or flowing down or into?

Thank You for the video 👍🏽

Thanks did work.

Use vinegar.

This is an impeller not an agitator