Відео

Thank you!

Fj

Nice job.. doing that next weekend.. thanks 👍

Yeah, it doesn't rub on flat ground lol but as soon as you get any suspension articulation, I'd reckon they'll rub pretty bad.

Murks 😢😢 Saustall in Werkstatt😢😢Fachliche Anwendung Mangelhaft😢😢

If you don't put the car in brake service mode and try to push the piston in you'll blow out the caliper seal 😢. I learned the hard way

Nice review. Thanks.

Thanks for the help it's positive the pully shouldn't give so much play

Probably a dumb question but where did you apply the carb cleaner? Did you spray it all over or just certain parts of it? Thanks!

Your gonna have different speeds with the bigger tire. I installed a rough country speedometer calibrator behind the gauge cluster as a fix. But you might be able to use the ecutech level 1 chip as well. So you know.

I would put that mudflap back and trim it

What brand halos are you running ?

I’ve stripped the top bolt.. where can I get that replaced? Under what name ?

That grey connector is for the factory usb connection

Were the nuts on the Y-pipe welded on or just rusted really badly? Getting ready to install a new catback and want to know what I'm getting into before I start pulling it apart.

great instructional video bro... i just picked up one of these ebay machines..

I got a 08 dodge caravan with the same key no crank all the lights work on the cluster but no crank

I actually did the same thing but now have a buzzing/engine noise from the left side. I think a bad ground??

Is the LX470 unable to run LED lowbeams without a resister built in? I just purchased a full set of LED lights, and they all seem to work without a problem, but I can only get one side to work with the low beams. Is your mod to get an LED with a built in resister to fit in the housing essentially?

2013 RAM 2500 - worked like a charm! Thank you for the excellent tip.

Do they work on a 2wd? I can’t find any for a 2019 classic 2wd 5.7 level.

Hello can you give me the size of every piece because I want to do the bumper by my self

How hard was it to attach to your rack. I have almost the same style rack and am looking at getting this same tent. Looks easy from the back but was the front more difficult because of the fairing.

So sick bro!!! 😎

You should invest in a better mic. I had to lean forward to turn up the volume on my computer and I hurt my back a little.

Please replace the cluck

Similar issue here, but mine is 200x300 (not 300x200). Same solution, but the short crossbars must be spaced vertically instead and that did the trick. The second set of longer bars went unused. Note that the 200x300 solution offsets the center of the mount a little over 1 inch which is not a concern from weight distribution given these these as so light now, but it may be a consideration if you want to precisely center the TV between 2 near sides (such as over a Fireplace mantle)....as such the location of the mount bracket attachment to the wall would need to compensate for the offset. For me, it was not and issue given my TV location.

you did not feed the cap top in first. they are to lock in the bracket

I really enjoyed your Drummond island videos. Great work and content.

Bro I just tried this method and it was spot on. Thank you for your services and showing that there's good people on earth

Is this new part you updated in the bio still running well? I bought the fuel pressure sensor from Oreilly’s and am getting the P018D now. I’m not sure I’ll be capable of wiring the new connector and just got quoted $890 to fix it.

Looks super nice! Well done brother

Just got this for free. Home Depot is selling 2 batteries for 299.00 and you get the light for free.

I think if you just cut the inside lip on the mud flap you could retain it...

Love your honesty!!! The video was super helpful to this novice chainsaw user. Thank you!!!

Oh gosh! Thank you!

I do not believe this! Try doing some aggresive 4 wheeling!

You can save time and money by just replacing the a/c compressor clutch.

Was the auto bleed with the scan tool enough or did you do more to obtain a firm pedal? Thanks😅

I put the rim on the balancer first to find the heaviest point then put the yellow dot there. It hardly ever corresponds with the valve stem. I have even found the dot machine off by 25degrees on all four same set but usually dots are close to where they should be. I match balance my own cars. Corghi 5000 touchless machine best purchase ever. You did well with that mayflower tho.

What part of the country do you live in? I understand the air lift suspension you seem to be happy about isn’t so good in colder climates such as ND.

I cross threaded mine too, 😂

I'm having the opposite problem. Will start the truck but won't lock or unlock it. I have to take out the actual key to open it.

Just got mine. This Tool has already earned it's Respect in my tool collection.

Hey man.I am doing same thing with my 2013 4runner trail.My question is what did you do with fender flare that extends on to old bumper and it is not painted it just black

thank you!!!!!!

😂 that’s commitment!

I did a low profile all day today as practice and I think using lube would’ve helped 😅. I did it a few times without terrible ripping it, but I definitely teared that thing apart after 30 or so dismounts

I don't have a probe can you tell me an easier way,? Like turn the AC on and see if the wheel intermittently turns in and off?

Its not the same as my ram 😢