Відео

Sa ferait plaisir 🎉😊

#1 Dieselmeken 8 #2 benzinjection 8 #3 bosch 6 #4 dieselmeken 7,5 #5 mynä 8 #6 benzinjection 8 #7 bosch 6 #8 benzinjection 8 #9 mynä 8 #10 benzinjection 8

GOOD JOB Shane!!!

#1-Bosch 6mm #2-Benz Injection 8mm #3-Dieselmeken 7.5 #4-Dieselmeken 8mm #5-Myna 8mm #6-Dieselmeken 7.5mm #7-Dieselmeken 7.5mm #8-Benz Injection 8mm #9-Benz Injection 8mm #10-Myna 8mm

#1 Dieselmeken 7.5 # Dieselmeken 8.0 #3 benz injection 8 #4 myna 8 #5 Bosch 6 #6 Dieselmeken 7.5 #7 diesel Mecken 7.5 #8 Bosch 6 #9 Mynä 8.0 #10Mynä 8.0

#1 benz injection 8 # benz injection 8 #3 myna 8 #4 myna 8 #5 Bosch 6 #6 Bosch 6 #7 diesel Mecken 7.5 #8 Benz Injection 8 #9 Myna #10Benz Injection 8

#1 Bosch 6mm #2 Benz Injection 8mm #3 Bosch 6mm #4 Benz Injection 8mm #5 Mynä 8mm #6 Dieselmeken 8mm #7 Dieselmeken 7.5mm #8 Dieselmeken 7.5mm #9 Dieselmeken 8mm #10 Mynä 8mm

#1 dieselmeken 7.5 #2 benz injection 8 #3 bosch 6 #4 myna 8 #5 benz injection 8

Can someone explain why 10° after top dead center not 24° before top ❤dead center thanks.

#1 Dieselmeken 7.5mm #2 Mynä 8mm #3 Bosch 6mm #4 Benz injection 8mm #5 Dieselmeken 8mm #6 Dieselmeken 7.5mm #7 Dieselmeken 8mm #8 Benz injection 8mm #9 Mynä 8mm #10 Bosch 6mm

1# benz injection 8 2# benz injection 8 3# bosch 6 4# bosch 6 5# dieselmeken 7.5 6# bosch 6 7# bosch 6 8# benz injection 8 9# benz injection 8 10# benz injection 8

#1 bosh 6mm #2 benz injection 8mm #3 bosh 6mm #4 benz injection 8mm #5 myna 8mm #6 dieselmeken 8mm #7 dieselmeken 7.5mm #8 dieselmeken 7.5mm #9 dieselmeken 8mm #10 myna 8mm

Mine are ringing out at .7 except for pin 62,63 they are at 101.8 and 33.5. which glow plugs would these numbers correspond to? The pins on the connector go from 61-66. 61 being cylinder 1?

1: Dieselmeken 7.5 2 : Mynä 8.0 3: BenzInjection 8.0 4 : Dieselmeken 8.0 5 : Bosch 6.0 mm 6 : Dieselmeken 7.5 7 : Bosch 6.0 mm 8 : Mynä 8.0 9 : BenzInjection 8.0 10 : Dieselmeken 8.0

1# benz injection 8 2# benz injection 8 3# bosch 6 4# bosch 6 5# dieselmeken 7.5 6# bosch 6 7# bosch 6 8# benz injection 8 9# benz injection 8 10# benz injection 8

#1 bosch 6 #2 dieselmeken 7.5 #3 myna 8 #4 benz injection 8 #5 dieselmeken 8 #6 dieselmeken 7.5 #7 myna 8 #8 benz injection 8 #9 bosch 6 #10 benz injection 8

#1 7.5mm myna #2 7.5mm benz injection #3 6mm bosch #4 7.5mm dieselmeken #5 8 mm dieselmeken #6 6mm dieselmeken #7 6mm benz injection #8 6mm benz injection #9 6mm benz injection #10 7.5mm benz injection

#1 dieselmeken 7.5 #2 benz injection 8 #3 bosch 6 #4 myna 8 #5 benz injection 8 #6 bosch 6 #7 dieselmeken 8 #8 myna 8 #9 dieselmeken 8 #10 myna 8

I’m not gonna even try to guess, but I found the rack operation interesting.

#1 bosh 6mm #2 benz injection 8mm #3 bosh 6mm #4 benz injection 8mm #5 myna 8mm #6 dieselmeken 8mm #7 dieselmeken 7.5mm #8 dieselmeken 7.5mm #9 dieselmeken 8mm #10 myna 8mm

I think ...... # 1 bosh 6. # 2 benz injection 8. # 3 dieselmeken 7.5. # 4 myna 8. # 5 benz injection 8. # 6 bosch 6. # 7 dieselmeken 8. # 8 myna 8. # 9 dieselmeken 8. # 10 myna 8.

#1 Bosch 6.0mm #2 Dieselmeken 7.5mm #3 Benz Injection 8mm #4 Dieselmeken 8mm #5 myna 8mm #6 Benz Injection 8mm #7 Benz Injection 8mm #8 Benz injection 8mm #9 Benz Injection 8mm #10 Benz Injection 8mm

#1 dieselmeken 7.5 #2 benz injection 8 #3 bosch 6 #4 myna 8 #5 benz injection 8 #6 bosch 6 #7 dieselmeken 8 #8 myna 8 #9 dieselmeken 8 #10 myna 8

#1dieselmeken 7.5 #2 benz injection 8 #3 bosch 6 #4 myna 8 #5 benz injection 8 #6 bosch 6 #7 dieselmeken 8 #8 myna 8 #9 dieselmeken 8 #10 myna 8

#1 (Bosch 6mm) #2 (Benz Injection 8mm) #3 (Dieselmeken 7.5) #4 (Dieselmeken 8mm) #5 (Myna 8mm) #6 (Dieselmeken 7.5mm) #7 (Dieselmeken 7.5mm) #8 (Benz Injection 8mm) #9 (Benz Injection 8mm) #10 (Myna 8mm)

#1 Bosch 6 mm #2 Benz Injection 8 mm #3 Dieselmeken 7.5 Etc…..

i dont know much about pumps but good luck to the lucky winner

What's the real differences between the 603 and 606 besides how the fuel pump is controlled?

Thank you

looking forward to the tests - finally someone doing a good comparison. keep up the good work man

Best diesel motors ever made especially the OM617

Is this the same on the stock edc pump?

Hello, I noticed your website isn't working any longer. Are you still selling the kit?

How much does it cost?

Why don’t the dieselpumk uk show this

Nice general overview of these series of engines. The six cylinder engines are naturally balanced and should run smoother that would be their main advantage. The change to a cross flow cylinder head is not that big of a deal with a low RPM diesel engine design compared to a high revving naturally aspirated gasoline engine design because the engine is not being power limited by airflow usually. If your trying to hot rod one of these engines the cross flow design might become more useful though. I don't like turbo charged gasoline engines because in my way of thinking you could just put in a larger displacement naturally aspirated engine and get the same power with less complicated plumbing and expense and heat under the hood, however in a diesel engine I will concede that a turbo is nearly essential just due to the fuel itself being higher in calorific value it needs the extra oxygen to burn the fuel efficiently or else you tend to get black smoke out the exhaust and less power than you would expect for a given displacement because you'd have to use a shorter injection stroke on a naturally aspirated one or smaller injector pistons to get the right fuel air mixture. A turbo basically increases the displacement of an engine in a way because the turbo adds a lot more air pressure and flow than an equivalent non turbo one I am not sure how the little 2.5 L made just as much power as the 3.0L one though I don't think it is just in the cross flow cylinder head design but I don't really know Mercedes diesel engines well enough to make an informed guess but I would assume there is a better camshaft profile to go along with the revised cross flow head design. Also I don't like turbo charged gasoline engines because the added power puts more stress on the engine parts compared to just using a larger naturally aspirated engine of equal power output, so your turbo charged gas engine will fail sooner. The modern trend of putting large 4 cylinder turbo charged engines in US built P/U trucks is unfortunate and dumb and is over all bad for our environment but it is the EPA that forced this path. Turbos for racing are a great thing though but race teams have the income to replace engines and rebuild them with all new parts very regularly.

Does the bi8e run quieter than the 75l3 at idle?

Thank you fit this a great explanation. I appreciate you showing what else is out there.

Question, if I wanted to swap my om606 turbo engine in to my chevelle wagon, would you recommend a aftermarket ecu and harness or a built mechanical pump to replace the edc pump? I'm still trying to decide and weighing the pros and cons of each option. Thanks for the element information.

Great subject. Can you tell your opinion about puting together an OM616 (240D) with a small turbo and PES 4M pump from OM601? Do you offer external ADA for PES 4M pump? And I am not afraid of blowing up the engine, they are plentifull and I would not go big with pressure and fuel... OM616 loves to rev but I can not keep up with the traffic.

Does this 8mm edc pump have an anti jerk feature like dpuk?

Awesome. Which MB 5 cylinder engine would you recommend as a good swap candidate for a mid 90's Ford F-150 pickup? The factory 5.8L V8 needs work, but it's such a gas hog, I'd rather spend the money on a better engine - hence a MB diesel powerplant. Not looking for a HD powerhouse either, I'm ok with the smaller 5cyl vs a 6. Thanks!!

hello sir, your video is really great, well done, we would also have liked to see from you this famous Mercedes om617 injection pump timing set at 24° before TDC set to the drop with swan neck with the electric pump? normally 3 drops per second on cylinder number 1 according to Mercedes recommendations? thank you and see you soon

I have a 1998 e300 turbo diesel how much I need to spend in a 350 hp fuel injection pump and I live in Dallas tx

Nice video.. Quick question Will a 94 om605 engine run with a om602 pump.

Many greetings from Croatia 👍Can I ask you if you can tell me if it is enough to replace the pump on the om606 and put it from the om 603 model? Is the engine running normally? Or do I have to do something else? I plan to put a motor in the boat. thanks in advance. 👍🍻🍻

I need to do this , wondering how do I make sure diesel won’t be spilling out

The fact they're making cars with no lock pin is a crime on itself, faulty equipment

When’s it available Shane? Don’t keep us waiting hahah