Відео

there's no way that is coming on with no fuse. I have the same unit and I've changed the fuse many times over the years. This time it didn't work, and I am trying to figure it out from there. My standby light comes on when the unit is turned on but none of the green lights will come on. I have the remote but that didn't help; same thing, only the red light comes on. This is a great receiver and worth it to get it going.

MANCA LA POSIZZIONE DEI FINALI L'ORDINE DI POSIZZIONE

bro make me happy to your info about the pioneer PAL007E ic iam search in internet but i cant get any info tq

I was looking for the schematic and was unsuccessful.

Dial pointer is backwards man…

Thanks for this dissambly, helped me with some similar model.

I don't speak English... Very, very tanks you

thnx bro, i repaired my pioneer, the ruber boots where causing the problem.

That makes more sense of why my sub 1500 barely moves

Hey man can I contact you? I need help with an issue on my CA-800..

This is the first video I've seen of this topic SHOWING how to rig this up, thank ya. Was lost trying to crimp butt connectors to tiny electronic wire haha. Then bought breadboard. Gotta get those soldering skills

🤝

I remember the Pioneer units had a problem with skipping. What causes that? I don't mess with CD players much. One I fixed yrs ago the disc was spinning too fast, found a pot to adjust the speed down and it played, I assume they use a marked disc and strobe to set speed. Most had loading drawer belt issues. I used to get them at Pawn shops for cheap not working. Got a Sony 200 disc changer at goodwill, the loading mechanism was out of whack, I think it got bent, I got it fixed and loading CDs fine. The CDs had to be clean and the grabber pads had to be clean, if you handled a cd and got skin oil on the edge it would slip away during loading and make a mess. You had to pull the cover and untangle the mess, and damaged CDs. Bad design Sony.

Have you found a source for the fusible resistors? and good quality replacement parts? I think I have about 20 amps and 20 TVs in my shop right now. I did the schooling yrs ago, now that I'm retired might as well get into it. I didn't forget much. I have seen some bad hack jobs, not on TVs but a lot on stereos.

The glue around those caps is corrosive and conductive. I purchase "for parts or repair" units but sometimes they list them as that and they work.

Where do you find these broken units, Ebay has tons but they want a fortune. How do you know these STK chips are fake or real? or any chip FTM

Whats on the little board you plugged the aux into?

Do you still work on SX-636's?

Do you still work on SX-636's?

Necesito reemplazar los STK0080. Donde los puedo conseguir? Gracias

I’ve been thinking about this for a while and I finally looked into it and yah 🤘

Looking for a good eq to buy ,got one to sell?

I had the idea and i was just looking to see if it would work. Cheers.

I fixed one of those and own one - cool strong amp

The springs in pioneer car cd players drop and cause this same issue too, but only with cd-r playback

I have a Pioneer DEH-P3700MP from 2005. I powered it up and it worked fine on the bench. Wired up my car for it and plugged it in and it worked great, but the next time I tried to use it it refused to power on. I couldn't get the CD to eject. Looking at the circuit board, the caps look to be fine. I found a service manual and schematics for this unit but it's way too much for me to understand. Any ideas?

Hey I’ve bought this awesome Equalizer. All works fine except the 1 KHz band of the spectrum Analyzer that always reach the maximum level. Can be the capacitor in one of this Ten drivers with transistor that you showed ? Hope you can help me. Max

Can I skip the front panel and use this amplifier directly?

Hi, can I get this data sheet please?

Hi my studio 5 stopped working and I tried different things and it won't turn on. Please help me out..

I have one just like that. Mine has an On / Off only switch. No ability to switch polarity like yours. Mine needs a new fan, and new Nichicon capacitors on the power board, since the original output capacitors vented, and are bound to completely fail, trying to spin that fan. Fan is noisy as hell!!!

man, do I understand correctly what needs to be submitted 12v 0.4mA 5W. 5W1 this 5w and max 1A ???????

what happen if i connect 600w subwoofer to it?

I'm listening to this on a X-502 amplifier board and two 40W speakers. Sounds great!

This will work with a device that has a polarized plug?

Awesome info....anyone know where part 2 is?

How can I choose the mono output from this module?

Hi Bro, Could you tell me where can I get the parts for assembling? I need make a 240V one . Thanks.

Just got this machine at a thrift store yesterday, very much appreciate this fix

Does it take a 16 awg wire, or something smaller?

I just bought this and the regulator IC positive side burned within seconds , hooked up a 3 amp 12-0-12 supply, was the supply rating to high for this preamp or IC defective?

Can you please do a video on the things you can power with this please

Se te ocurre probar con un multímetro que no es True RMS😅😅😅 ambos tienen variación ninguno es exacto como lo es con un multímetro RMS

What is the wattage of the Rogue PRM-806? No one seems to know!

Am I right in thinking, that this can be plugged into the phono inputs on an integrated amplifier and a turntable can then be plugged into the vacuum tube buffer? So if I understand it correctly I would not waste the phono inputs on the amp, but I would be getting that tube sound!

Hello, how is the response in bass and treble compared to the pioneer GG 9800?

You blew your amp. But it was not plugged in. Well it was actually the VU meters. Ha ha!

I have the same amp ... it has no left speaker output ... looks like both inputs make it as far as the mono switch, but left meter and left output are dead. I'm a noob so still trying to figure it out. Any ideas where to start looking? Thanks. Good find, btw!

God bless you , you read My Mind!

What happens if you add a 6 inch passive radiator? Also, would a 5 inch subwoofer make an improvement? If not, what's the specs for the speaker you used? Wattage, frequency response, sensitivity, and speaker model? How would I eliminate the port? Is it glued in?