Відео

Close valleys are one of the worst things to come over the border they go down just the the close cut pipeboot rage of the 90's what about that 3" stagger

Hello, this is impressively good done video! thank you for sharing!

Wrong 😂😢

I'm having this done to my house in a couple weeks but the roofing company is using lomanco deck air. Still, this video is by far the best video i have seen detailing how these systems work and proper installation. Thank you!

Clear concise succinct and easily understood; THE BEST INSTRUCTIONAL ON SHINGLES OF THEM *ALL* Thanks Mack 👍

THE BEST

Thats is exposed asphalt and insurance fail the 4 point inspection simple like that

You don’t even know how to use the gun my boy.

Yes sir

Great analysis. Agree with your "weighting" decisions, even though they all favored OSB. For roofs, it's all about the water (unless you live in Buffalo, then it's all about the weight of the snow).

I didn't know about these vents until this video. I just had my roof redone and I specified the O'Hagin vents to be used. They have just been installed, and they look fantastic! I requested the shingle-over install like in the video. The vents blend in really well with the roof. I had Malarkey Legacy shingles in Silverstone color installed and had them use the light gray O'Hagin vents. I could not be happier with the results, and all because of this video. Thanks! 😀

thank you! very helpful video.

I have a construction company at my house...are shingles supposed to overlap (not horizontally but vertically)?

Hello can use peel and stick modified base instead of poly glass?

Where can I buy it . Great job

why not do both of those steps and then add closure flashing? Looks like if you only did the flashing (2nd example), there would be exposed decking where the soffit of dormer meets the roof deck. If you put shingles all the way up and under the soffit as far as possible (your 1st example) and add flashing as you showed, you would eliminate the exposed decking and the flashing would add barrier to water getting to end of facia board at roof (causing water to absorb into facia and rot). Finally add closure flashing piece under soffit to keep water from getting under the shingles where soffit meets roof.

Ummm... That's hardly surprising dude

🙌

What do you do when the roll starts to run off away or towards the seam?

Thanks!!.........this helped a lot !

Chimneys are brick? nails in brick?

affrain barkala

What kind of hammer is he using with those cap nails? I need one!!!

Thank you!

Over rated an good hook blade in an X-Acto knife works like a dream

That vent is total crap.

My roofer said they can use 3 tab shingles to make the ridge, since I will be using 30 year shingles I don’t feel comfortable using 3 tab shingles for my ridge, he mentioned that the ridge cap shingles are expensive and that it takes up a lot of bundles, that’s the reason he suggested using the 3 tab shingles for ridge, is this true?

I 100% agree with the results but disagree with the Superiority of the OSB to be used for roof deck! Here in the Philippines, the primary feature that we need is the Pull-Out rating because we have many Strong Typhoons that can fly our roofs. Second, we can just buy a very cheap "WATERPROOF" Underlayment in between a standing seam roof and a 3/4 Marine plywood.

Exellent video thank you

That bit at the end gives me all the confidence i need to walk on tiles. But mostly i love how the next suggested video to watch is 'how to repair a broken roof tile' hahaha.

Also, when you put the caulking in the middle of the water channel it makes a damn and causes water to go under the tile the wire is a great idea. That’s how I do it.

You are supposed to use the valley metal that has a hem on it to keep the water in the valley and also you’re nailing through the valley metal so what good does that do all you’re doing to create a hole in your valley metal

Your results are exactly as I would have expected. And that’s why my home is OSB. I mainly used it re the water retention and rot potential. It was also nice to save about $300 in cost.

use shoes with soft soles

Great video. What type of nails or what size nail is used for the ridge cap? Thanks.

This is the way to do comp valleys because they look very professional. When installing the full shingle up the valley set those to a semi dry chalk line. Blue works best. People can see up the valleys from the ground so you dont want wavy valleys.

I like the woven valleys best. Then cut valley..

Exactly the video I was looking for. Thank you!

When does the full sheet start over & do you just repeat the pattern?

Your videos have helped me so much! Thanks a ton! Fortunately I had a hipped roof but i was curious what doing a valley would look like. Seems like open valley is more diy friendly. Cut valley seemed a little less diy friendly but very doable. Woven seems like it would be easy to make it look messy for someone just learning this.

Spraying water into the inside of the roof😂

All excellent videos sir

Similar idea used for long(er)-term drywall mud storage--level the surface to reduce peaks and valleys/surface area. But you want to clean off the sides of the bucket with a knife, then brush and water. And make sure it stays cool. It'll last months in a cool environment. For short-term storage (1-5 days or so), leave 1/2" of water on top of the mud. Then, dump it off when you open it.

Dude, your presentation style is way too similar to Lenny Pepperbottom of Neature Walk. lol

The pen is mightier than the sword. From script to spoken, your words will have prevented many families having the police knock on their doors. That is truly mighty. 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

Great video, very helpful. I would though, really love to know how to turn an outside corner properly with that type of low rise flashing. Are there any videos or any resources you could point me to? I've been searching all day and can only find stuff about cutting and bending regular drip edge around outside corners.

Lmao that was great. Thank you

In zones that get freezing weather like he says leave a slight gap, you are supposed to leave a minimum ¼ inch gap from the fascia and drip edge. This prevents surface tension ice from traveling under to the decking.

Yes, they're are bad actors in the biz, but to categorically say "say no to door knockers" is stupid. Door knocking is my mine source of new clients. I've never scammed anybody. All my customers were happy they chose me as their roofer. 🤷‍♂️

You got the 9"&18" right but your 18" Nail pattern is wrong. Instead of every 18" putting 2 nails even with each other your supposed to stager them so you gave a nail every 9" alternating sides.