Відео

Can you just recoat the clearcoat on a paintjob. Do you have to remove the old clear coat somehow or just sand it .

How many CFM is your shop air?

How much is cost

Love it !! Exactly what I needed !

How do you replace rear 1/4 panels on front fenders of 95 Z71 chev. Do you have to remove fenders. If so how do you get the piece straight. Thanks.

Amazing work! The fact that you went above and beyond and even put por15 I wish we had more people like you! I know 90% of people doing this wouldn’t even come close to your work! Wish I was closer!

Thanks for walking me through my 2004 3rd gen rocker panels. I live in Nl where corrosion is king Lol. I am going to take your advice and go with full OEM outer panels. I have to replace the inner/centre also, but my problem is that the inside floor is lip is also corroded and has to be replaced. I do not see them anywhere on line. Do you make your own, and if so can you post the template, W/ dimensions for your viewers. Also what after market replacement panels do you find best? I have seen some very thin off shore junk out there. There use to be a company in Ont that made good ones, but their name eludes me now, or if they are still in business? I am putting all this together now for next spring. I just had a hip replaced, I am not a lazy arise, its just that it will be that long before I can get onto a concrete floor again to take the inside floor measurements. So if you have a template made up to share, it would be greatly appreciated as it has a lazy curve to it . Thank's for sharing your knowledge, Cheer's H

You’re very good thanks for the videos gonna tackle mine This winter! ❄️

Is this better/more durable than wrapping in film? Im looking to dechrome, including the front grill and wondered which was the better option.

How much would this cost ?

Sick asf

There are numerous holes in the rocker panels. Are there plugs for them to keep salt, dirt and water out? Also on my 2011 Sierra 1500 SLE extra cab there are numerous holes of various sizes all through the frame. Should they be plugged and what size plugs do they take and where to get them. It looks like GM and Chevrolet have set us all up to fail on these 30 thousand and up trucks. My frame now has welded plates on both sides because of rust.

I also looked for weld through primer at princess auto and Canadian tire, they didn't have any. I looked on line today and it looks like their are a lot of different kinds, what type do you use. Their is a postal strike so amazon doesn't look good.

You don’t have to prep the stainless or chrome for adhesion? Can I use the SEM product on chrome?

I went to princess auto yesterday and they don't sell paint or epoxy primer that isn't in a spray can. I picked up a small paint gun that I thought might be good for this job. Rocker panels cab corners and 1/4 panels. It is called a Vapor LVLP gravity feed touch up spray gun.It has a 0.8 nozzle. Do you think it will be good enough for all materials ,epoxy primer, high build primer, paint ,and clear coat.

I’d like to see how to do tail light mounting panels , great videos by the way .

where do you buy the box sides? All I can find is part panels.

hey man do you happen to know if the steps would be the same on a 2013 sierra single cab work truck?

Heck,I have painted bumper covers and fenders with the same paint and had the match off a bit! Plastic parts are just tough! Look at most newer Chevy Camaros.The rear quarters dont match from the factory!

It seems like the last few jobs I have done are all tri-coats,2 of them were Hondas! They were fun to match,ugghh. Thx for the video

Wondering why you didn’t use Bull Dog Adhesion promoter On the bumper 1st. Or is there a need to ?

Another nice job looking good

Hello, Do you know if I would be able to put a clear coat (2k clear coat) on top of the SEM paint?

What about the primer color. What is best gray, black ,red. And what about the different temp of the primer reducer mix, how do I know what to use their.

This gives me hope to fix my daddy car. Locating someone i trust is the hardest.

Nice work

Can you tell us the air pressure you are spraying at for the sealer, paint and clear? Thanks Jon

This is amazing

Thanks for trying the paint gun .I don't paint that often. So often I like to know how it works. Cause I'm cheap .

The plastic that you use for taping and painting, how do you buy that stuff ,does it come in big rolls .

Do you put the two coats of epoxy primer ,and the two coats of high build on at the same time or do you have wait overnight between the two types. And can you spray the primers on right out of the can ,or do they have to be thinned , and what type of thinner ,what is it called. Thanks. I really like your work. I hope I can get the same results.

Turned out amazing!

Did you take the gun apart and do a complete inspection and cleaning before using

Thanks for showing plastic repair, learn something new every day. Really appreciate your videos. I used to paint cars on the side at local tech college. That was 25 years ago. Now I want to do repairs on my own cars. Thanks again.

Great video. Thanks. Thank you for your honest opinion of Temu. I have a few of their guns but have yet to use them. Thanks for your opinion of the paint gun cups.

How much lol and where do I drop it off

where did you buy your arch panels ?

Beautiful

Thank you

Where the cab corner overlaps the rocker just below the door jam, (small indentation) is there anything you put in there or is it just tight as you can get it and left alone and just finished paint work? Currently working on one now and realized it.

Do you have a video on 95 chevy Z71 4x4 two door extra cab , with back seat ,rocker panel replacement.

Thank you for info

how long do you let the primer dry before paint, and then how long do you let the paint dry before the clear coats.

Looking good.

Get a dog. It seems to help all the other UA-camrs 😂

Which exact line of ppg epoxy do you use? Thanks

Love that old truck.....my very first vehicle was a 79 f150 was originally same color however it had seen a few color changes over the years lol always thought about taking back to original but never did

Thanks for the content.

Thank you for the video... very helpful sir..👌🏻

How do you tell when you have block sanded enough, or taken enough off. Or taken too much off.