Відео

I somehow missed this when you released it. Some suggestions if I may. Get a Ingersol 235c air impact for all the tough bolts and don't worry about the Ryobi haters, they will always hate unless you use what they want. Also get yourself some welding tip cleaners for the jets, they work better that drill bits and are closer in tolerance. Soak the carb in penetrating oil and tap on it while it's wet with oil several times, if that don't work, make sure you don't have any gas in it and heat it. I have used a heat gun so you don't have an open flame around it, and by using the reducer tip on the heat gun it should concentrate the heat enough to get it out. Just remember it's pot metal so it doesn't have much strength

Ever find the issue with this mower? My tiller had me scrathin my head for days. Darn thing would idle day n night. As soon as u moved it,,, sucker wud shut off. IT WAS THE FUEL CAP!!! 😏

I really enjoyed this video and learned a little bit too!

Play the bonds plastic and rubber

Windshield blue

I cut the filters apart and the Walmart ran do the fram

The only difference is the length of filter he's all can be attained at your local Walmart most in the even the Walmart super tech man who is 100 times better than a frame

Or even NFL 400 deaths if you have

For a PA 16 off of

You can use a 3614

Wipe it on live it up😊

Go to the O'Reilly Auto parts buy a gallon of d&w tire black and you won't have to rest blowing yourself over the torch

4000

No you can use them you can use to steal push rods

Have you changed the oil ? If there is oil sludge on the governor parts inside the engine that could cause engine surge ! While typing you got the new carb on and it sounds really good !

Are you sure that is the correct valve cover ! I do not see a crankcase vent tube that would go to the air cleaner !

When these small engines surge it is usually governor related !

...those appear to be shielded bearings, not sealed bearings...

AWESOME......!!

Look it up on the Internet and see how it's all set up

That bolt on the wheel opposite the one with the sprocket acts as a set screw to lock it to the live axle. The wheel with the sprocket has a ratchet system that provides differential action to allow the mower to turn. The bolt on the sleeve that slide forward to engage the blade if used to adjust the belt tension. You have the light duty blade for cutting grass and small brush. There was a much heavier brush blade available for cutting heavier material. It weighs five pounds.

if you need a old allis motor b allis series i have one in closet i spent 600 dollars on way back 030 over.has 4 hours on it.i had behrens machine do the work

i have a mint sears craftsman 22 hp that thing wont die its not a lawn tractor its a garden tractor briggs i dunno what year it is its green had to replace electric clutch in in one time.47 inch deck

Easy flips.

Turned out sweet

25,300

Anyone I know what a booger wallet that put together again it's not a permanent repair on thin metal now you can get a filler that is called metal to metal by Africa that does have aluminum cut in it

I Love your Videos Makes Me Feel More Confident to Work on My Own Stuff NOW !!! Thanks ! WhiteTigerFire.

ua-cam.com/video/iuhwjWWqfWw/v-deo.htmlsi=wK3rUI6bo5PqkxSn😅

Kyle do you follow Musti1

These mtd tractors really aren't horrible machines.their box store machines.your not getting a kubota.keep the spindles clear of grass change fluids filters.try to find one with a kohler.and it should be a happy 10 year realationship.

you mentioned that you want to add a fuel cut off on the gravity feed system, is there a reason you wouldn't or would do a fuel cut off on a fuel pump system ?

You lied Bro! You prob had a 100, for sure you had 40 but had to go and lie...disappointed .

Like your channel i have learned a lot from watching it

Kyle I live in Dayton Oregon wish you were in my area your a good guy and very fair on your prices and it looks like your a good Dad

I had a 2000 craftsman just like that I restored the whole had it for a while then sold only the one I had was a six speed manual

WORK BENCH A MESS YOU GOT TO QUESTION THE QUALITY OF WORK ,ALL THAT REFLECTS IF YOU ARE A PROFFESSIONAL OR NOT JUST WATCHING AND SEEING

WRONG AIR FILTER TO SHORT WILL WORK ITS SELFOUT THAN DUST AND DIRT AND GRASS GET IN ENGINE AND RUIN ENGINE YOU JUST FIXED ATTENTION TO DETAIL NOT THATS JUST FINE ,PEOPLE WATCHING LEARNING BAD HABITS DO IT RIGHT THE FIRST TIME

SHOULD ALWAYS DO COMPRESSION TEST TO BEFORE TAKING THINGS APART AND BLOW AIR ON ENGINE AND THE WHOLE MORE BEFORE TAKING THINGS APART ,STILL WATCHING AND YOUR LEARNING

AND YOUR BENCH NEEDS TO BE CLEARED OF DIRT AND OLD BROKEN PIECES WHEN RE ASSEMBLING STUFF, IM WATCHING AND YOUR LEARNING

YOU CAN LEARN FROM OPINIONS THE RIGHT WAY IS TO SET ENGINE ON COMPRESSION STROKE THATS WHAT YOU WANT BECAUSE BOTH VALVES ARE CLOSED AND CHECK CLEARANCE MOST IMPORTANT THATS THE PROPER WAY NOT ANY OTHER WAY BECAUSE VALVES CAN BE SET WRONG THAT OTHER WAY, DONT CARE ABOUT VALVE CLEARANCE IN ANY OTHER CYCLE EXCEPT COMPRESSION CYCLE ,LOTS TO LEARN ,

Que medidas tem as rodas e pneus dianteiros. Referencia??? Obrigado.

just compare that machine to todays machine. No access to anything and lots more plastic to break

I'v used an auto brake shoe spring tool on those springs down there much more easer to struggle with when getting them on or off

btw / Fyi I've been meaning to tell other on here on those leaky tubeless tire beads to use some type of Permatex Thread Sealant liquid tape on the tire Beeding before re-setting the tire side beading as it will seal it much better and when you put it in water to find and bubbling you just tap it with a hammer to stop it as a few old rims that were major leakers and use it the type I used were also meant for gas line threads so it was allot more sticky so have on some deposable rubber gloves too LOL

I have the signature 2000 Montgomery wards version of this mower its relabeled but its Mtd too its the 14.5 hp 42inch deck only thing beside the motor size here Is that I haven't seen the Seven speed shifter on either sides of it.. this model isn't as common unless its located somewhere around the center just below the seat or something.. also you can probably find that center missing panel as I have the same one on my mower there a common part

hello. i have a problem when i drive slow, quad is jumping, when i drive fast its almost stop jumping. But when i release the throttle then stops jumping. do you have any idea what could this be? i have suzuki king quad 300 1995

Kyle I fixed that cub it was the shoulder spacer on it it turns amazing but there is a loud whine from the transaxle I topped it off still there any ideas?

Hi,Kyle I have the earlier version of that D R brush cutter, it's called the Bachtold Whipper. Mine was made in the early 70s I believe. It works excellent every year I need it. DR definitely made some changes since mine was produced. Mine has a bigger engine, a clutched pulley on top of the drive shaft to the blade, A big rotating disk to protect the blade area. I've cut down small 1.5" trees with that thing it just rips. Mine will never be for sale. It works perfect.

Nice job. Glad to see your battery was still good and you didn't even have to touch the carburetor, that's a big time score also noticed you have a Fluke Multimeter, that's a good quality tool. I am still putting together my 23-year-old Yard Machine that I took apart repaired and painted. I'll be watching.