Відео

Legend, Iv just done it on my xc90 2.4 d5 2014 and works perfectly. Thank you 👍

Excellent video, you've certainly put it to good use! Bought one in 2019 "used" from Ebay for £200 box had been opened and it was all there but had never been used, got signed up for a large cylinder, full size regulator and a rotameter (ball in a glass tube) flow meter to accurately set flow. It’s certainly paid for itself! Only issue is I mostly weld outside (garage full of motorbikes and kitcar) and gass blows away and get crappy welds if thre is anything more than a light breeze- might have a try with flux cored wire if it'll take it , Daves garage Mk 1 Escort swears by it. Take care!

We have a 2007 Coachman which we have toured for twelve years now. In that time the rear lights have done exactly as yours have. The main issue has been the two large cracks at the front above the centre window that are now 2mm wide and run from the window seal up to the gutter. In addition to these severe cracks there are around ten to fifteen hairline cracks around various exterior joints, mostly where the rear panel joins the roof. Other than these (that I'm now dealing with) the caravan has been great. I don't think the quality issue is unique to Coachman, I've seen three year old Buccaneer caravans with cracks and issues.

Hi floyd, would you be able to change glow plugs for my corsa? how to contact you?

I just found your channel and I have to go back to part 1 and follow up on your work on the Simplex. I purchased a started one with a boiler many years ago and wish I had had your advise about getting something done every week, it might be finished now. I also would be interested in joining your club for folks who don't like clubs. Dick B. USA

Floyd, I am so pleased that you have decided to carry on making your video's. They are a great help with my Simplex rebuild. Some good problem solving and ideas. Kind Regards, David.

Thank You ever so much! I really appreciated your walk through, so a spanner like me can understand it. Best wishes to you and your loved ones 😅

Спасибо за видео! Но добавлю от себя! Если у вас перестал вращаться выходной вал, но мотор работает, то это срезало шплинт на паре шестерня-червяк. В принципе, можно даже без разборки корпуса вставить новый 3мм шплинт. Главное - найти то место, где он вставляется. А доступ к месту, появляется, если снять большой мотор. Мотор снимается очень легко - надо открутить лишь две гаечки на торце, где крыльчатка. Кстати, можно и не снимать крыльчатку, а демонтировать весь мотор и после всех манипуляций, опять его поставить.

Stop yappingbrat

How do you get the engine code

Doing a great job, following your videos as I am at the same position as yourself with my Simplex.

Building the same loco which I bought in the same state of construction as yours. You are really helping because you are addressing the same issues that I am having. keep the videos coming sure you are helping lots of people. Looking forward to episode 11.

how would you repair the metal washer bit that holds the bolt for height changing?

I love mine. Works so great I didn't realize I even had one until recently.

Floyd, I used an (IRWIN 1602L3 Visegrip 4in Long Nose Plier £15 @ Amazon) to grip the shaft near the barrel and then a large flat head screwdriver in the gap to extend the shaft. I then released the plier and clamped it closer to the barrel again and repeated this process 3 times till the shaft extended to final tightness. This saved using an assortment of spanners.

Hi Floyd The reason this Delphi Technologies document is so confusing is because it has an error in the text. The text should read "Screw the socket ANTI-CLOCKWISE so that the groove for the clip emerges - Install Clip. The image the text refers to shows anti-clockwise rotation of the barrel. Using (right hand rule of thumb) clockwise rotation is indicated by your fingers when your right hand thumb points at the clock face. I used a mole grips to hold the barrel whilst using a13mm spanner to rotate the shaft to losen it. Later I used the 13mm spanner to hold the shaft still whilst I rotated the barrel anti clockwise.

Thanks a lot, it works exactly as you said! The brake works again!

Hello mate has the grill got two fires from the top and bottom or has it only got one at the top? Hope for you to get back soon!

Thanks, this worked a treat on my old xc90, I’ll be using this method tomorrow again to adjust the cable on my new xc90, excellent video by the way

Thanks had mine 3 years proved to be a success,then for some reason the tools would'nt 1:54 stay connected watched your video problem sorted

I know this is years in the future sir. BUT THANK YOU!!!

helpfull i have the akulon 8x25 .. great optics for the £ .... kinda needed more... i got some akulon 10-25-50 ...not very good .. great at 10x..but zooming loses the quality noticably..and focus adjuster needs re setting..i kinda like 10x its enough..so i have bought these cmpact 10x21 i dont have loads to throw at binoculars..im hoping the fix focal length will be good quality.. nikon has a rep after all

You replaced it at the right time, they fixed the bottom oven for the sixth time then did something to the top oven which broke a week later and took two weeks to get fixed which has only lasted for four days. Little did I know whirlpool is just a name plate as whirlpool hotpoint is owned by the owners of the beko group. I found that out doing research. This cooker replaced a new world and the new world replaced the blomberg by beko which seemed to break down every week.

Was tryna listen to a podcast while on my bike but couldn't hear anything and it was so frustrating Thanks a lot and hopefully thisll work when it's really windy

You are such a boring Pratt .

Fantastic thank you

The brake system is on the super Simplex design drawings, but looking good so far, I’m in the middle of building two 😢 i must be mad! I get all my parts from Black Gates engineering, they have a full kit for the tanks and cab! Ade

If you getting a telescopic rod pay some money because the cheap ones damage so easily

Good work 👌

We had a blomberg version of the becko your getting and the ignition and light switch kept melting.

Ours has gone 5x in a year and a half 3x under warranty and now will be the 2x out of warranty. Seems the bottom oven breaks down every 3-5months.

Great review of the hold and side view. Just bought a pair for birding.

April 2024 Update: After the pratting around caused by the puncture mentioned below I found that the awning is stable with the pressure at just 4psi instead of the recommended 7psi. No problems so far.......

The conveyed button is the note of c. Below it is f, and above it g then d. The chords are the same but major chords. The missing bits of the straps connect to the top of the accordion and then you put the 2 straps over your shoulders. 🪗the flaps are valves that allow air to pass through the reeds on each reed plate in one direction at a time. When you pull the bellows air will flowmtheoufh the top reeds, and when you push the bellows it will flow through the bottom reeds on the reed plates. I would have used rubber solution and not superglue to srick the valve on in case you ever need to do any more repairs.

Thanks for this video, it's been really helpful. I have the same cannon model bought from Currys in March 2023, the same problem happened yesterday. Unfortunately for me, I didn't take out the 5-year plan. If they don't have the electronic gas-safe device part available, you cannot do much. I have never had a problem with gas cookers. Then, I have never had a temperature oven before.

Don’t give up on the engine, steam can be frustrating some days especially when things break like taps but there is always a solution

a lot of companies dont hold stock anymore, they rely on their supplier having stock, when the 1 supplier runs out of stock- nobody has stock. same with boating, we were after a fuel injector for a nanni engine- everyone showed it in stock, when contacted they then phoned the suppliers, who didnt have any in stock, thus all the companies in the country were out of stock because the one supplier was out- turned out that the engine is a common kubota block and if you want kubota part, it was a fraction of the price- and dozens available.

@iareid8255 3 months ago Floyd, have you thought about turning the compound slide by 90 degrees. As it is, the parting off action causes the compound to move on the slide, i.e. the side nearest you will want to lift and the toll dip, the amount being how tight the slide is. By rotating 90 degrees, the length of the slide (probably twice that of the width?) will be in the direction of parting and I believe will be more rigid? That said on my old Student lathe, parting off was difficult and nerve racking until I fitted a rear tool post onto the cross slide, parting off is now easy and can be done quickly. I also use a carbide insert parting off tool. @floydraser4603 3 months ago Actually no, I hadn't thought about that at all but now you mention it, it looks fairly obvious! I will certainly give it try next time. That's also another vote for a rear tool post. Not sure I do enough to make it worthwhile but I'll see how it goes. I'm awaiting delivery of a carbide tip parting tool too, a bit more substantial than the one in the video. Thanks for the comment. @floydraser4603 3 months ago I've now given this idea a try, in principle anyway, not actually partied anything off yet. Yes it works in that it more of the cross slide is used to make it more rigid. I still have to wind the cross slide back as far as possible otherwise the tool is moving away from the round post underneath. @iareid8255 3 months ago (edited) Floyd, the mounting of the tool post is rather weak on your lathe. This is presumably due to the design for the clamping of the compound to the saddle? I suspect there is not sufficient depth of material to set those two nuts in a counter bore such that the nuts are below the compound's top face? In comparison, the Student has the tool post bolted directly to the compound slide so is more rigid. Even so using the main toolpost was not great, but my lathe is fairly worn, hence the rear tool post modification. @floydraser4603 3 months ago @iareid8255 Yes it is a bit weak. I'm going to persevere with it as it is and if I'm not happy I'll probably go for the rear post and mounting plate for my lathe, currently about £70 from Warco.

@thosoz3431 3 months ago Winky's flexing parting tool holder is a great success. His plans are free and easy to follow. @floydraser4603 3 months ago Just had a look at his video. That's a bit of a project which is fine if you need something to do and have the materials. However, it doesn't eliminate the overhang.

in general i think the only difference is the quality control applied, but even then, not every machine will be tested, the more expensive machines may well have passed a higher standard of quality control, but that doesnt mean the cheap one is any worse than a bad one that has passed QC.

Comments transferred from the first version: @steamsearcher 3 months ago OUR EMCO came with loads of problems a Compact 8 E which is the variable speed version. The first thing I looked at was the parts which were the most popular to replace. Leadscrew half nuts? Upon a good look the leadscrew was very rough. I then took the whole lathe apart. I polished the leadscrew and all was fine. Although old it had probably been used just once. Everywhere was covered in protective grease, including the spindle and bearings. These were flushed out. The cross slide screw was bent straight and all the ways polished. I then made up a new spindle nose to fit Warco backplates and move it out to give me a chance to get my GRUBBYS behind and do the M 8 ts. Heated up and banged on to a frozen spindle. Then machined in place and removed so several chucks and faceplates could be machined. Having other lathes comes in handy. 9 in total but some came free but in a bad way. Now it is a superb machine but underpowered for big cuts. the Raglan 5 is for this or the Super 7 from Myford. David and Lily. @grendel1960a 3 months ago i think the difference between machines is the quality control at the factory, dictated by the customer, so the more expensive brands will have rejected the worst of the dogs that were made, which will then be sold by the inferior brands @Marcus1954s 2 months ago Axminster have Sieg lathes. Amadeal, Chester and Warco have the Weiss lathes. Reply @floydraser4603 2 months ago That's interesting, thank you for sharing. I guess each of them have a given level of quality control on import. Reply @Marcus1954s 2 months ago @floydraser4603 Axminster informed me that they did not do anything to the Sieg lathes they import, just sell them. The Weiss lathes I've seen from Chester, Amadeal and Warco are technically so close that the parts for each particular Weiss model are interchangeable. Considering how they are crated/packaged and shipped I doubt they perform anything more than a superficial check that all listed parts are enclosed. Never seen a major issue with the Weiss lathes.

Thanks for the video. I paid 15 quid for a nearly-new mower of the same design and it's heavier and harder work than I expected (have a big garden) and the grass collection box is near useless. I would just leave the cuttings on the grass but it doesn't trim them small enough to avoid thatch buildup. It will be getting resold. Still it was fun to play with and I have crossed it off my bucket list which has some value I suppose.

Great Video will definately make my job easier Thank You and Well done

I was hoping for a review of these binoculars as to how they actually worked out in the field as far as brightness and clarity of the optics. All this review did was give how much they weighed.

Can you use this welder without gas?

Update 20th March 2024: No further news on the problem but I have now managed to sell the cooker and covered my losses. Note that selling a cooker on Facebook Marketplace seems to attract the World Champions of timewasters!

I like the repurposed coffee maker. Perhaps my disused old thing won’t get thrown out after all✔️ Perhaps a regulator handle that’s not so heat conductive. Maybe simply a plastic sleeve round the end ?Playing with steam engines and wheels wizzing round ♥️♥️

Im going insane trying to work out how to adjust the angle of my internal mirror..

I have an old jump pack. Love it cause it has a 12 volt cig port. I never bothered to open it to see about a battery replacement. Though im considering doing that.

great idea - did it last?