Відео

Thank you for the video.

Interesting job Tom heart fix. Never seen that Gallo gun before, do you think it ‘could ‘ unblock a heating pipe safely with blowing off a fitting?

For me, better without the music, just the high speed work noise is more pleasant. I suspect most will disagree with me though.

Another good job done Tom

Nice one Tom well done getting it sorted for the customer, thank you for the video.

Funny that I was only talking about stop taps on the last post 😳

Great video Tom very interesting some thing to make a mental note 😳

Great video Tom. I must admit I hate those stoptaps- lever valves are far superior!

Interesting one that Tom, you just never know do you in the Plumbing world, hope alls well. 👍🚽

Had this happen a couple of times with the jumper dropping, also had it where there has been a load of sediment caught in the valve where the water board had been digging outside. Great video as usual mate.

Had this happen a couple of times with the jumper dropping, also had it where there has been a load of sediment caught in the valve where the water board had been digging outside. Great video as usual mate.

Glad to see you put a ball valve on Tom. Much more efficient than existing valve.

If it can go wrong it will ,always wen ur under the cosh..or customer is a pain,,,well done...

When u cut the main line u should have checked the pressure then😊

Odd place to have the stop tap. Behind the bath panel. Dead handy in an emergency 😂

Annoyingly these jobs keep you grounded as a plumber as all they do is eat up your time. Great vid as always Tom

Never seen one a those gallows guns Do a video on one or have you already

You can tell seating is damaged from the spindle , the all head should come out with it … you done a right thing replacing whole lot … they’re almost like a red gate valves exactly the same principle.

That was an odd one Tom, just shows how a fairly simple job can escalate.

Tom saves the day again, as always a great vid mate.

When the main surge of conversion to combi's was underway I had a load of similar jobs where the installer had tried to turn off a tight stop tap only to snap the head off leaving the stop tap almost shut. The installer is on a tight price so they just left it ! Another one to watch is where a new stop tap has been fitted leaving the old one unseen and again the head is broken off and almost fully off! I wondered who would get these sort of jobs after I retired 😀!

Well done Tom, what a pain of a job.....but as always you sorted.

Interesting job there Tom, well diagnosed.

hero!

We used to get that a lot of this when our gangs cut in a new outside meters when they turn back on no water in the house. Half the time just needed to turn the stop cock that released all the crap, also blocked PRV, blocked non return valve, old stop cocks burid in the floor or the wall, sometimes you would find stop cock fitted the wrong way round. I have now retired thank god.

You sure do get the most bazar jobs Tom, They make great video content Mate 😂 😎👍🤜

Tom your a good plumber, must be so much headache these jobs.

I’ve done bathrooms with the same walls , it’s amazing how much weight purely the tile will hold , and a bit of CT1.

Nice content Tom, interesting problem too, another one to commit to the memory bank! 👍🏻

Ace job Tom😊😊

Very good Tom, you got it fixed. 👍

Love them lever valves, I don’t use anything else now.

Well sus out there Tom ,and why you trying too see how hot it was after you just heated it up with a Blooming big torch😂 Harry will having giggle if he’s watching ,nice work as always Tom ,see you on the next one 👍👍👍👍👍👍🇬🇧🇬🇧🇬🇧🇬🇧🇬🇧🇬🇧

Diagnosis and problem solving all in a days work tom. Everyday is a school day.👍👍

I had a similar issue with a stop tap that had been fitted the wrong way around. It was down the side of a washing machine so it wasn't easily accessed so I turned it off in the pavement. When I put it back on the rush of water pushed it closed and nothing came through. Keep at it Tom

👍

Interesting Tom, shows that you need to check every thing!

Great perseverance with this one but as you say move the stop tap to a better location it is not really accessible.

Very strange that Tom ...at least you fixed it ..don't know why the other guy could not fix it 😯

should have used a screwdriver to smooth that silicone tom 😜🤣 was the tap in the right way? if not the water flow closes the washer in

Too many chiefs, not enough Indians Tom😂😂

Hi Tom, an interesting job there, I have seen that before but not for a very long time. Well done, that’s another job sorted and a happy customer. Have a great week Tom and take care. 👍👍👍

Great video mate. Dedication blowing the stop tap like a flute

Thanks great fault finding Tom fantastic you could isolate the probable problem and fix it.

Great video Tom. I remember some of the old style stopcocks if you installed them the wrong way round they wouldn't work, the water pressure would push the jumper down on its seat. If you gentle turned the water back on in the road they would sometimes work. 👍😎

Strange one.

🤘😎🤘🫖☕️🍪🎥👍👍🇬🇧

Great problem solving Tom......well done buddy.👍👍👍

Great problem solving Tom......spot on buddy.👍👍👍

Think you get more than your fair share of bad luck Tom, Top work well done mate.