Відео

nice brother. view from brasil

Thanks mate, very helpful 🤙

Hi mate I've watched your video back a few times as I'm trying to find out where exactly on the transmission is the main TCM / BCM plug? Its the loom that runs from the transmission to the TCM or possibly the BCM or maybe even both I'm not entirely sure but any help or direction would be much appreciated mate

Some good tips here. Cheers

Love the videos where it shows everything that my cat can figure out, but how to remove the axle from transmission, because they all are stuck in there, nothing.

274nm, what is it in lbs/pound? thanks

Great video guys. One of the best I've seen.

Just so you know you-tube.... I will never ever use any company that advertises on here.... cheers

Was that much space between the crank and the rod surprised it didn't bend the valves

Very good video 👏🙏

Ah, the old gatorade bottle, eh?

that is sweet, love it

wow that needs a clean

Why is yourt T31 so different than mine? i have a T31 2008, 2.0 diesel. And the location of the parts is not in the same place .

Like a kitten! Hope you are well mate.

Sweet 👍 I'm putting a 253 in my HG KINGSWOOD UTE .

What was the size of bolt and thread pitch you used to release the rotor from the hub? Nice video btw

Nice video .. Ive seen lots f trannies taken out before ,but this is the first time ive seen it done without a beer .

Not enough oil changes

Hey mate is it possible to install it wrong I left gsp shafts at shop and 3 days later all kinds of noise started, what could they done wrong??

Great video thanks mate, unfortunately my idler pulley mount snapped when prying off the pulley. Any video on replacing this by any chance?

11.46 iv got 90 gq nissan ute trubel bleed the brakes . Iv fitted new front roters pads new brake cylinders on the brake drums . New brake booster new master cylinder . Iv tried two people bleed no good Iv tried gravity bleed . Tried back bleed them still pedal sinks to the floor under foot shit tried every thing I can think of need help cheers Rob

thank you

Byron You must be so bloody busy with so many cars you're working on & being a family man 😝👍 Your property & shed / vehicles every friggin where is absolutely awesome 😝 You are living a good life & doing what your passion is CARS & working on them ! You luv to talk 👍 & Communicate like the words just automatically flow ! some network should give you a car show to do seriously 👍 Mate why the hell would you take a car to Pedder for suspension check 🤔🤔 id say you would know just as much about cars than some of the staff at tender age of 19 - 20 ive seen here at Pedders in Bundaberg Qld hey ! Please keep up the video's on Commodores / In particular Calais 2004/2010 if possible ! Cheers from Bundy 🍹🕺

G'day from Bundaberg Qld 😝👍 i really do enjoy all your knowledge & videos 👍 only just found you because im looking at video's on 2004 VY Calais Suspension/ Centre Bearing , Now im hooked watching / learning from you ! Ive got a long way to go il admit ! Brother You have all the good gear ( tools & handy tricks of the trade ) i luv tinkering on my car like doing service on it but must be honest tackling this Suspension is big job 🥴 Thanks to Aussie Car Guys like you my fears & worries are not as daunting as first thought 😁 Every family needs a Mechanic in it hey 😂 Life would be so much easier 😜 Steve in Bundy 🕺🇦🇺

Cool video matey 👍 im learning how to replace front & rear suspension on my 2004 VY Holden Calais , Im now thinking i should of done mechanical apprenticeship & learnt all the tricks when i was a young pup ! Im 58 & learning as i go & by watching a 1000 videos on VY suspension & from Guys like You 👍🕺 Steve from Bundaberg Qld 🍹🍺 if your ever up this way you're welcome at my joint to give a hand & enjoy a big bbq & drink 🍹😝

Mate iv got td42 in my 90 model nissan ute . It's hard to start mainly in winter when it's cold . But once get her started will run all day . But I pump the primer up until it's has full presoure but once she starts the primer lost its presour pump it up again but dose the same . Iv ordered new glow plugs x new set injectors hope that helps . Iv put new primer pumps on but still same result. The Ute is 34 years old engen never been pulled down Iv owned her for 27 years love her just trying improve her a bit . As said once she running will go good on long trips . But next morning she hard to start again . Thort I would ask some one the no the voters cheers Rob

Thanks Byron You repeatedly helping me out big time!

I think I stripped the hole on the subframe 😬

Need ur help I have a vz 05 5.7liter 6speed sedan car ran then stops so chanced fule fitter it runs an lease than 2 or 5 seconds stops running wood my fule pump have shit it self

Cheers mate just did this on a Volvo S40 and the low end power is back once again.

Thanks a lot real help

Cheers mate love the video it was awesome, now after watching your video im all set to do mine and now im getting the run about on which is rhe correct service kit, repco has 3 kits stating they fit my vehicle, but i dont think any of them do, im only planning on using a repco or ryco kit ( quality kit) do you still have the part number for your kit you used? Thanks mate keep up the good work

About to do this with my 2001 wh grange 🎉

awesome job

Can you use 0w 20 for Xtrail 2008

thank you

Just curious to know why would you run a thermo that opens in the 70s to then the new one to open in the 80s which causes you car to run hotter.I would switch back to the 70 degree thermo as it opens a lot sooner and keeps your car cooler.

I always thought if you pump the brake with bleeder open, that air could get sucked back in from bleed screw leaking - is this not the case?

Do you have a video of jacking a CX7 onto four jack stands - that would make swapping tires really easy... I looked underneath but I could not identify good lifting points to get four jack stands setup. Also got to replace the prop shaft soon, then it would really help!

Good vid mate

Amazing video! Very well explained, thanks!

Champion. Thanks mate!!

Thanks for a great explanation. My mechanic wanted to replace the whole shaft and buy it interstate with all the added costs and labour etc! About $100 for the 3 pce kit on eBay for an old car I love that won't have heaps of k's done on her anymore anyway. I'll be more than a grand up afterwards. Cheers.

Отлично!👍

ONYA CHAMP THAT HELPED OUT BIG TIME.MY IDLER PULLY SHEARED OFF AND THAT HELPED ME RIGHT OUT ✅️

Absolute legend