Відео

Just what I was looking for. Nice and concise, but enough detail that I'm confident.

Amazing work ❤❤

That was very instrumental and to the point.

I literally have a switch with two black wires one green wire and then I got two red wires coming out of my wall and two black ones and a ground wire I have no idea where to begin

My hinges are broke. Can u just replace the hinges?

Very helpful thank you!!

I really appreciate this video thank you so much I’m installing two ceiling fans and light together but I only have 14-2 wire running from electrical box to fixture so both fan and light it’s being controlled by a dimmer switch I know it’s better with 14-3 but in this case that’s what I have so thanks again for the video very helpful

Loved the instruction and common sense advise.

I wired mine this way exactly but the switch does not turn on of the power to the fixture. The fixture is getting constant power still. Any ideas?

if your switch is stuck in the on or off position and doesn't turn anymore, you don't need to replace the switch. Just disassemble the knob by removing the retainer clip behind the knob, and remove the spring loaded ball bearing inside along with that spring. Then reassemble. The knob will continue to work without the ball bearing. If you're too lazy to remove the ball bearing, you can buy a new switch for about $1 on aliexpress or temu.

Thank you so much man of making it simple. Ace, thanks legend of simplicity. 🙂 worked instantly I used socks because my latch release is not like yours,smaller. It was easier than I thought too. I approached it violently just like you said. I thought it would take man strength, thanks anyway. Independence is so lovely and uplifting. You've made my day. Thanks also for the DW 40 tip I didn't know that would've used original DW40. I didn't know that one existed in UK never seen it before. Bye

Finally someone that simplified how to do this. Great

Such a great video! Thank you so much for putting it out there and for showing the detail stuff too. I really appreciate it! 🙏🤙

Thanks!

This is very helpful and it looks clean Thank you, we do not want a transition strip.

Someone told me a loud out of a fan (for two ceiling LED light fixtures) is not recommended and I should run independent dedicated wires. Should I run a separate wire for the light fixture or can I use the fan 14-3 for the load out just like the fan built in light for additional ceiling light that isn’t part of thr fan?

Thank you for this very thorough video. I don't understand how to use gap tools but online it says my iridium spark plugs need a feeler gauge not a coin gauge. I'll check to see if you have any videos on gapping.

Awesome, man, i was able to do it. With such ease ..

What kind of grease is that, brand and type, or link if possible?

Well damn! This was MUCH easier than using a saw!

Very helpful explanation! Thanks.

Great video thanks

I replaced the alternator on my euro civic with the 1.8. It was a little difficult to get the belt in line, because that tensioner is very hard. Yes, it's very important to watch your hands while doing this, getting a smack from that tensioner could possibly break some bones.

I like to pigtail my plugs in by themselves

Thank you it worked

thank you

Damn pest, ruined my lawn.

"Not too wordy" thank you!

Thank youuuuuu! Very helpful!

What are you doing with that other red wire with the tag on it? do you put a cap on it? Do you leave it alone? Is it safe to do nothing with it?

Thank you!! I like the plywood tip!!

Thanks so much I’m just literally outside the house that I’m going to work on doing this 🫡

Thank you for sharing

omg, you literally saved me!! thank you so much😭🥹💖

Gonna be hard to dig up the concrete around a sapling, or whatever you call a tree that's close to 3ft. It's growing between my garage, and patio slab. My thoughts are heavily water what little bit of soil is present, and try to gently pull the tree up.

I was just looking for baby bunnies in my yard and I found your video, thank you for the tips!

Thank you very much for the video. Just need to learn where to put the bottle jack to raise the mower to replace front tire on riding lawnmower. Grass needs cutting! Lol Yes I'm an old woman but not a dumb blonde. 😂

Excellent video, thanks for sharing

My door blew off not long ago. So does all of them have a spring? Because i found all the pieces but maybe it’s the springs I’m missing

Nice... Thanks for the simple and to the point video

Is this the same way on older models? I have a LT150 Deere.

Guessing everyone here has the same car. Anyone got a passenger door and a passenger side fender

Oh.

legend ! thanks

Had to help my neighbor with her rear tire, had no idea how to do it before watching this video. Easy pesy! Thank you so much!

Excellent, excellent video.. I liked the top down view of everything. I am replacing 2 wire with 3 wire so that light and fan can be controlled separately. This helps tremendously. It seems as though I should be able to do it. I'd call an electrician, except I need this done 4 times.. if I can just learn it once, I can quickly/cheaply replicate it to the 3 other rooms

Nice video thank you.

Much easier by removing front pass wheel

Thank you. I have rabbits in the yard and didn't realize there were burrows. 😊

Thank you. This is very useful and full of great tips.