Відео

all thread is pretty expensive, are you using 24inch x 1/2 ? not to mention the cost of washers and nut. can you share your purchase amount here. I ask becuase id like to copy your design for a 40ft 3 ft tall retain wall

Turned out great. I like the way you formed it up. I'm thinking of doing something similar in my front yard, but half the height and slightly less length. Great video angles, too. Thanks!

NO MASK???? Always wear a resperator doing this spraying.

Я порекомендую убрать все острые углы на швеллерах, что бы не ранить себя или других!

Nice!!! where did you get the rod/square washers? what sizes are they and materials? Thanks for the video.

Nice job!!

Is a 4" ledge enough to hold an I beam?

where did you buy the back panel for the van ,? awesome work

👏👏👏👍It seems that you have a variety of skills. Good job bro.

Dude, this is almost exactly the plan I have for some walls I’m pouring this week! It’s like I’m getting a test run vicariously through your video. Only thing I was gonna do is use stainless rod segments and leave it in. I had the idea of cutting the spacers, but didn’t want to leave tunnels in the wall. But while watching this I realized I could drill out an inch or so of the pvc once forms are removed, then plug the holes with concrete. Thanks for sharing this!

Looking forward to the full length video! Keep up the good work!

If you guy will be in Utah I can help lol

love the safety crocs

Your pretty strong. I just installed HD springs in my F350 Superduty and it was a bear. Wrestling the new spings in through the fenders and dealing with 4 inch dual exhaust. Its pretty rewarding knowing you saved a bunch of money.

What does your home look like? I'm curious about your final shot of everything. Your project turned out great.

Ah ya already figured out it wasnt stiff enough. I didn't look at how old the video was

If you're going to galvanize it i sure hope you add some 2x2 along the bottom. They don't call galvanize HOT DIP GALVANIZE for chits and giggles. Your headache rack is going to warp.

With the bed mounting holes through the top of the frame just imagine how much easier this would have been to cut some 3x3x¼ blocks to weld the channel to with holes in one side to run your bolts down through the top of the frame for mounting. Then one wouldn't have to worry about trying to figure out all that notching over the hump and give you some place to run your fuel filler neck hose between to 2 frame rails.

It’s great seeing these kind of videos gives inspiration to work on my own car

What company makes that ?

I think trash it like wd4000

Would you call it an AMBUDUMP or a DUMPULANCE?

you mean dump van 😂

That will work

Can wait to see it

Very nice, looks good.

Great work! It's clear that you put a lot of heart into your videos. If you ever need help with editing or animation, I'd be happy to assist. Good luck with growing your channel!

What all the holes? Do you fill them in with something?

What all the holes? Do you fill them in with something?

Bein looking for this kind of video for 3days thengk u man

With all the holes in the frame might think of beefy it up you could put another rear end under their and make a tandem axle truck 19:55

I used to have a welding shop and most of my business was building grain trucks. I loved them fl series freightliner. Most people will tell you that you can't build a 10 wheeler out of the f l70 but we did. Normally, we went with a full screw and all we did to the frame was put a 3/8 x 3 flat bar on the bottom flange all from the back spring hanger of the steer axle all the way to the back of the frame. Cabs set high enough to build controls to the back for dumping in augers.

Depends what your cab to Axle ratio is if you need the cheater axle sometimes they hang up on curbs are truck did so took it off just have to see what you can bridge on it did my stuff right d o t never bother me my dad had a frr who would buy a single axle and cut behind the cab and make it into a tandem went down road weird like v shaped but never broke my brother in law brother his truck got to job and frame rotted out behind cab was stuck in truck till fire department freed him bad thing is just got back from a 40 mile run to get rock imagine if happened on interstate my trucks where double frame and heavy duty and well maintained i been there and done that 55years of it now retired 😊 12:41

The annoying music is louder than your voice.

Man i just found your channel, those porches turned out awesome. Iove the timber frame roof detail. Keep up the great work.

A little bit of information when you use your threaded rod grease them and the rods are much easier to remove

Good truck

Some narration would have been nice.

nice work cowboys🙏💕

First time ! You look like doing this all your life long

Would it have been better to extend the membrane down a few more inches and actually go over the edge of the footing just to have a safety margin?

Digs the hole then jumps in and cleans it himself!!! I salute you

Man I miss running excavator and building with concrete . Nothing like the smell of concrete in the morning

👍👍👍

did you plug the holes where the plastic pipe came out ?

Fiberglass Cab on the Van. Who makes it?

It's bad enough you doing this crocs, but using a rock as a hammer is just showing off. good work. I am a do a 2 foot tall by 8 in wide probably 40 ft long at my place, Ima mount a gate on top of it...all custom no less. great example and thank you...I think you can use this same concept to install a pool also.

Thats a P.L. ambulance. If it came from Maine you prob got from sugerloaf. Would be a yellow sticker in door jamb. I prob built that in mid 2000s

Cribber here. Simple but effective.nice job man

Great job! were doing the same in the Philippines.