Відео

i am moroccan i looking for where i can find it this pantalon please answer me

I couldn't tell if it worked or not

I klnow this is 5 years old but I will leave this for others before they screw their panels. Wrong screws, not designed for sheet metal. Use fine-threaded screws or better still, drill holes and use Nut-Serts / RivNuts. Never screw metal into metal without a sealant as you will most likely be using different metals that will corode. These plastic moulds are flimsy and should be bonded/sealed with Urethane sealant to body panels for sealing and strength.

Дизельный Х трейл красавчик, владею таким и доволен

Imagine tech screwing your car

Thank you!

I followed the instructions, Then put the firmware onto the card and put it into the 3D printer and turned it on but nothing happens

This is very helpful, however, we're having a couple problems. We're using a 64gb Scan Disk. Will this still work? Once I followed all the steps and reinserted the SD, it said "cannot read disk." Thank you for any insight! @jtactical

Good thinking J Tac, nicely done. I am setting up an old radial arm saw from my father. These ideas are great! THX pw

Territory vs patrol ;)

Enjoyed your presentation. Some great tips. Cheers from Australia😊

PERFECT!!!!!

What a godsend Thank you J-Tac you have just saved me going insane trying to print on the Ender -3 V3 SE. It would appear that Mac users are the forgotten tribe. Any ideas on connecting via a usb-c cable directly from Cura? I think there is an issue between Cura and the silicon Macs. Any suggestions would be appreciated.

Same issue last week, I’d say, you can always trust wd40 and a rubber wrench, fixed nicely, threads still work on both sides sunshade and scope, Just a bit of paint off the threads in the sunshade

Thanks! You could write everything down in the description so we could just cut and paste and then insert our device node. That would make it easier.

You are slow

Great video, how do you level the table to tbe saw arbor when the RAS is built into the workbench?

nice and staff but not really satissfying - i was hoping to see real uilding work

Hi the xtrail looks fantastic Any problems after you lifted the xtrail with driveshafts. Thanks

Hey question, you know from compressor to the shocker XL valve, should the tub be 1/2inch air line?

Hello from Croatia , where did you get your intercooler , dawes and needle valve , and oil catch from?

T31 CVT or Diesel AT?

А где бездорожье? Я по таким местам на рыбалку езжу на Ford Focus.

How tall are you?

Where is the offroad part ?😊😊

I’d like to know your preference on blades for the RAS

Thanks great review, I bought a pair of shadow grey love them so purchased another pair Coyote colour and a pair of there Greyman jeans. Absolutely brilliant clothing

Perfect solution well done

love the concept..as i'm currently still building mine i think i'm going to try 3 slots maybe 3/8"...1 about 2" either side of the blade and one right under the blade..really enjoyed the video

Mon viking imow mi 632 fonctionne toujours , Normandie France !

Sorry to bother you again. I tried going back to terminal mode and formatting the card again but I am still seeing an image of a key where I am supposed to enter a password. It will not allow me to type anything in for the password. I thought the sd card may have been in the lock position but it was not. Any ideas:)

Yep, this works. Thanks.

HELP:). I followed your direction but when I get to the password there is a picture of a key. I'm thinking it means the password is locked?.?. Not sure how to unlock:(. This printer was donated to our school so we are not sure on what the password was set to. Thank you for any suggestions:)

Have you come across $hex ?

Dzięki - przekonałeś mnie , biorę 💪💪💪

Hi. Do you stil use the robot? What is your opinion after few years? THX

Would work better for hoover style high speed suction. Probably too restrictive for larger dust extraction

what password are we supposed to use at the end<>?

This is awesome, you need more likes than this!

I still think this style of x trail is the better looking, especially with a lift and tyres

Nice video and modifications mate👍🏼 Well done😎

After five years, maybe time for a followup review? Did you actually ever use that insert for anything? I reach for my toolbox or my Swiss Army knife when I need a screwdriver or to fend off advancing aliens; I do NOT reach for my wallet. How did the card and cash access work out for you? Did the T01 end up in a drawer? I prefer the Maverick for its capacity and layout and I enjoy the weridly satisfying bulk and mass of all that machined aluminum. Been carrying it for three or four years and the stupid red paint job is long gone, chipped and scraped away-Dango's paints suck. If you're shopping for a Dango product, only buy raw aluminum or anodized finishes.

Great video When will you do a video of the Patrol towing the caravan and will you do a video on your Sprinter Van

Is that breamish valley

Off your lips if you think x Trail can compete HA HA

Awesomeness! Thank you so much for taking the time to do this! It worked!

Military 1st has great products. 👍

This pants color khaki or coyote?

what are the sizes of your wheels? and rims

Super video! Learned tons! Thank you mate! Subscribed