Відео

what belts do you put in if needed to be replaced i also have one but cant find the belts i need the nummbers thanks.🎉😊

Where did you buy the weather stripping

Man I have a few questions about the mower I didn't figure it out it says it's gear-driven so does it what's that mean does it have a belt

I'm on my way to buy one of these today.

If you spray WD 40 in the tube WHEN foam is wet. It will devolve the foam and clean it out

Thanks big guy great video

Those are not spring compressors those are widow makers!😂

Any idea what that outer soft tape is called that allows the rubber flex piece to slide freely on the harness?

You remove the front bumper if you don't know what you are doing. I've just change both headlights in my 2008 Subaru Tribeca and it was a breeze. No front bumper removal....

Thank you so much. I’ll be doing my own after a plumber came in and replaced the tubing but didn’t check to see if he fixed the problem🙄. Subscribed!

Thanks for the video just finished the swap. Helped so much!

I like this design, now you have encouraged me to make one for my Ghenoee. Especially the flagpole idea.

Thanks bro! I wish I could thumb up more than 1 time.

Thanks Big Guy!

how do i download the sound track?

You're an excellent teacher. Thank you!

Where’d you get the new switch?

I was been waiting to comment until I had enough time on the mower to see if this fixed my issue. I have the LX277 with the 17 HP Kawasaki engine. I would randomly loss power, sometimes it would come right back, and sometimes to problem would take 15 mins or more to come back. Very hard to diagnose since it did not happen every time I used the tractor. I replaced the coils last summer and have never had the loss of power issue since. Thank you for the advise. This fixed my issue.

A shop totally removed the crosspipe heatshield and now I feel vibration in the floorboard. There was only a rattle before but no feeling of a vibration. Any ideas what that could be?

You know that lug nuts have a specific ft lb which is mandated by the manufacturer. It’s easy to look up and use a torque wrench.

Mazda's equipped the E- Brake system the caliper plunger automatically retracts once you do the set up . This allows you to install the pads. Lots of bad information out there .

Great video.

Very helpful Thank you

Hey! I'm facing a very similar issue, but I got afraid to take the machine off from his place - perhaps to break something... May I just pull it outside? (i mean the entire machine)

I kinda think that plastif lining is not necessary? It must be to quite down interior road noise? What do you think about leaving it off?

How do you check the transmission fluid level on the 825 and what type of lubrication does it take?

Thanks much for the video. Had the same issue with broken wire hold downs for the bulbs. First repair was sloppy and a short eliminated my cruise control while on a road trip. Next repair was with solder and it's holding. I know now I won't be replacing the whole unit! I'll just keep on soldering.

With that hitch, you must keep your balls greased well... The tongue weight of "that Big Fat Thing" LOL is under 800 lbs.???

My question is that white stuff on the connector, is that some kind of heat compound or thermal paste or something? All the new ones I see have clean connectors and I am wondering if I do this myself should I be putting something on the connector. I am just worried about damage to other components. Great video.

Nice product I have the flat steel one but I only tow up to 3000 pounds it is working for me. Another thing on your receiver into your hitch. I actually bolt that on with a grade 8 bolt with a nylon lock nut. And the trailer hitch ball. I actually weld the threads to the nut so it cannot come loose and they can’t take the ball off with the hitch and take the trailer. The lock pin is OK but they can break that off very easily. But like everything if they want it, they’ll take it but they are going to have to work at it to take trailer and draw bar.

I have same tractor and same issues. Low power when engaged. New plugs, coils, New Carb with fuel pump and inline filter, checked all deck pulleys and compression checked (93 and 95psi) . I double checked the valves and one was loose by 13 thou but made no difference on running condition. After the new carb it seems worse. I am running out of ideas. Still a good video to help troubleshoot 👍

THANK YOU HELP ME OUT SIR

Amazon set of two 74.00

Thank you for this !!! You just save me some money and time

I found 4 broke wires and 1 almost broken

Does anyone have the torque specs for the bolts for the caliper bracket and the slider pins ?

lose the corny background music

Absolutely love this. Will be using this as inspiration for my build.

Having a basement helps alot 😅

I like the concept, but a couple negatives in my view. #1: It’s made in China. So I’m sure the bolts are made of a lower grade steel. #2: The body is made of aluminum…not ideal. Hopefully an American company can improve on the concept and make it with more robust materials. I’m sure it’s adequate for your use. Thanks for the video.

Yup. That's my problem. I finally found the right video.

Thank you for this video! I am heading outside to try and do this to my truck. Fingers crossed!

You may well have saved me $1,000 doing this myself thankyou so so much what a great video!!!

GREAT VIDEO

Sorry about your friends , but the facts are the pandemic was hyped up way beyond where it should have been and we were lied to by all in power ,,,simple IVERMECTIN would have saved your friends,but had the truth about IVERMECTIN came out, the emergency authorization for the VAXX would have been destroyed, the drug companies couldn’t have defrauded us out of billions of dollars and no one would have got their pay offs those in power should be tried for treason

Just got a rattle noise that would go away after some time driving. I was going crazy looking for where the sound was coming from.. I Though it was my engine looked at the other heat shields they were all in good shape.. except the driver side, it was corroded and rattling, thank you sirr!!

Very helpful. Just changed out my harness.

Thanks for the good review.

Thanks for this video. Gotta do this soon.

Just had this nh oil done on a 2016 mazda cx5 that had lived outside in NY and underbody was pretty crusty from rust. David in manchester did a great job including creating some access to ensure inside door frames were treated. Dropped day one and picked up 24 hours later. Just 9ver $400 including tax. Confident itcwillarrest the rust tgat was gaining a foothold but hadnt created structural ir even obvious cosmetic damage yer.