![Uncle Brent’s Shed](/img/default-banner.jpg)
- 81
- 351 806
Uncle Brent’s Shed
Приєднався 28 гру 2021
All things automotive related
The A Pillar is almost done
A pillar rust repair , VC Chrysler Valiant
#backyard #backshed #automobile #mechanic #restoration #offroad #diy #willitstart #garage #makita
#backyard #backshed #automobile #mechanic #restoration #offroad #diy #willitstart #garage #makita
Переглядів: 453
Відео
The dirtiest XR 6 iv ever seen , but it’s all there 👌🏽
Переглядів 52014 днів тому
ED Tikford XR 6 ford falcon , 1994 #tikford #backyard #automobile #oldschoolgarage #mechanic #rustyrestoration #restoration #offroad #willitstart #diy #ford #falcon
We replaced the sill panel on the rusty VC valiant .
Переглядів 83221 день тому
Rust replacement on a VC valiant , more rust than the titanic . #mopar #rustrepair #backyard #backshed #chrysler #valiant
We finally make a start on the VC Valiant
Переглядів 2,5 тис.28 днів тому
Chrysler VC valiant , Toyota 1UZ V8 engine swap , #automobile #backyard #mechanic #diy #offroad #sendit #willitstart #racing #adjustment #rust #rustrepair
10 minute How to , step by step roller rocker adjustment , 265 Hemi
Переглядів 685Місяць тому
Step by step roller rocker adjustment tutorial in 10 minutes. #yellaterra #automobile #backyard #offroad #diy #sendit #racing #willitstart #backshed #howto #tutorial #adjustment #holley #gasket
Finke 2024 , 2500km round trip
Переглядів 1,3 тис.2 місяці тому
2500 km round trip to the Finke desert race #automobile #rusty #backyard #mechanic #diy #repair #restoration #offroad #willitstart #offroading #bsa #finke #northenterritory
Morris J2 van , 1966
Переглядів 1 тис.2 місяці тому
Farm fresh morris van , #automobile #backyard #diy #mechanic #repair #willitstart #car #engineering #better #morris #backshed #downtheshed
Will it start after 15 years , How does a fuel tickler really work
Переглядів 4993 місяці тому
How a fuel Tickler really works , BSA Bantam been in storage for many years , will it start #automobile #rusty #mechanic #restoration #backyard #repair #garage #diy #oldschool #backshed #fuel #willitstart
First start in 50 years, Holden FC Grey Motor
Переглядів 9 тис.3 місяці тому
First start in 50 years , will it start , Holden grey motor and starter motor tutorial How a starter motor works #engineering #repair #willitstart #automobile #backyard #car #diy #holden #engineswap #mechanic #fcholden #ghost #backshed #downtheshed #better
Parked up for 50 years , will it run again?
Переглядів 15 тис.3 місяці тому
This FC Holden was parked 50 years ago , will it run and drive , No I don’t think so #automobile #backyard #car #diy #mechanic #engineering #repair #fcholden #holden #willitstart
Am I wasting my time???
Переглядів 5964 місяці тому
I’m I wasting my time lol . Rust repair section, inside seal panel on AP to VC valiant #automobile #backyard #car #diy #mechanic #chrysler #rust #repair #backshed #downtheshed
Never to see the road again , 1 UZ swap maybe??
Переглядів 1,1 тис.5 місяців тому
It’s rustier than the titanic 😅 #automobile #backyard #backshed #car #diy #mechanic #chrysler #burnout #valiant #engineering #engineswap
Will it start and run after 15 years??? Of course it will
Переглядів 99 тис.5 місяців тому
Will it start and run after 15 years , of course it does #automobile #backyard #car #diy #mechanic #chrysler #318 #burnout #willitstart #converable
We build the cheapest work bench possible
Переглядів 4016 місяців тому
We build the cheapest work bench possible
We work on Australia’s best VL commodore. I finally started working on the VJ Charger .
Переглядів 1,7 тис.6 місяців тому
We work on Australia’s best VL commodore. I finally started working on the VJ Charger .
EPISODE 2 Terraplane Hudson , we take a closer look at the engine like no other.
Переглядів 9 тис.8 місяців тому
EPISODE 2 Terraplane Hudson , we take a closer look at the engine like no other.
EPISODE 1 Terraplane , an engine like no other
Переглядів 105 тис.9 місяців тому
EPISODE 1 Terraplane , an engine like no other
WARNING ⚠️ Dodgy repairs on the towmotor forklift
Переглядів 609Рік тому
WARNING ⚠️ Dodgy repairs on the towmotor forklift
WARNING ⚠️ DO NOT TRY THIS AT HOME. HAPPY BIRTHDAY TO ME
Переглядів 561Рік тому
WARNING ⚠️ DO NOT TRY THIS AT HOME. HAPPY BIRTHDAY TO ME
The CNC ported Hemi 265 gets its first oil change
Переглядів 1,6 тис.Рік тому
The CNC ported Hemi 265 gets its first oil change
The CNC ported 265 Hemi is back together
Переглядів 2,8 тис.Рік тому
The CNC ported 265 Hemi is back together
265 Hemi rebuild , cam and lifters , oil pump and brace , sump and baffle
Переглядів 1,3 тис.Рік тому
265 Hemi rebuild , cam and lifters , oil pump and brace , sump and baffle
Finally the Hemi 6 is going back together.
Переглядів 1,3 тис.Рік тому
Finally the Hemi 6 is going back together.
Australia’s new YouTube creative burnout challenge
Переглядів 5 тис.Рік тому
Australia’s new UA-cam creative burnout challenge
Love the CM model owning one myself (on my channel) I think you need a diff ratio change. That first gear pull was crazy. I went with an Eaton truetrack in mine with a 3:45 ratio but also mines a mild 318 too so most likely would be different anyway. Mine sits on 3,000 rpm at 100 kmh. Bloody great cars though
What’s your channel brother?? I’ll subscribe to you 👌🏽
Great idea although I’d take one more step and adhere sand paper or emery cloth to the plate instead of lapping compound. The reason is the the compound will be wearing the tool as well as the head/block. I’m planning to lap my Model A head and block soon. The method I’ll be using is a piece of tempered glass laid on my machined cast iron table saw with sanding cloth lightly glued with low strength contact cement to the glass. I’ll cut up some 6”x48” sanding belts .
Yes that is a great idea , the only reason I did it this way is that I thought it was going to be quick lol Turns out it wasn’t. But we got there in the end 👌🏽
👍🏻🇦🇺✌️
Cheers mate 👌🏽
I like the way you do small pieces at a time. It’s looking too good for a “skid pig”
I’ll do a walk around on it in a few more episodes just to show how rough it is , don’t get me wrong it’s quite capable of going back on the road again , maybe that could be a future challenge????
@@unclebrentsshed4253 what ever you decide, thanks for the content! It’s good to watch work on a car that is so popular but little content available online.
That’s coming along real nice, keep up the good work.
Cheers mate 👌🏽
great vid mate..diy at its best.thanks for sharing keep them coming
Cheers mate , thanks for the support 👌🏽
Minty!
Cheers brother
Nice work Unc!
Thank you very much
That’s hot 🔥👌
🔥🔥🔥
Well done mate. A lot better than some of the shit I’ve seen and had the fun of fixing when they gave up. Well done uncle
That hole punch is the go👌👌
Yes it was a good buy and very quick to use 👌🏽
Captain sidetracked hahaha, love your work mate, now gonwork on your charger
Yes I know mate 🤦🏻♂️🤦🏻
@@unclebrentsshed4253 haha, what's another year👌👌
@@brettelliott4512 😂😅🤦🏻♂️🤦🏻
Spot on, for decades Ive used a diamond slurry charged metal lapping plate. I can acheive a flatness across the face of the block or head within .0005 tenths removing minimul material. I think its crazy as phuck that machineshops mill off .005 to .020 off from the block or head. Thank you for posting your video, great job sir.
Thank you very much for your input sir , very much appreciated 👌🏽👌🏽
The problem was slowly going away. then you stopped It from going away. 😂. Good job mate. Maybe I’d have welded a patch over inner sill. Stop from filling with junk. Like a job in the city. 👍👍 Good luck. Have a good week.
Cheers mate 👌🏽👌🏽
Never heard of a XR6 before. It would have been a XR4 in uk. Around 85-6 year. Could clean up good. A nice bit of Retro action. . Good luck. 👍👍
They made XR series falcons from 1993 right through till 2016 here in Australia 🇦🇺
Another gem.
Hell yeah 👌🏽
that bloke was ment to aell that xr6 to me about 8 weeks ago for 1500 was ment to takw it from pirie to adelaide for me to take lucky you saved it was going to strip it
Hell yeah 👌🏽👌🏽
When I was younger the first ed xr8 I seen new was in narembeen wa a cobalt blue the same as that a great colour and awsome carhard to find
Iv always loved them as I did my apprenticeship on them and have had a few since then 👌🏽👌🏽
@@unclebrentsshed4253 I used to own one of brocks EA Falcons good car only sold it because pandemic 😞
Hi mate silly question but would you have a 1984 mq mk Nissan driver seat and base that you are willing to sell mate to to keep my Dad's bus on the road I live in Port Augusta
I do but it’s a complete vehicle and would like to get it running one day
@@unclebrentsshed4253 no worries mate
I miss you when can I see you I love your videos so so so so so so so much from Aibhlinn ❤
Haha hello Aibhlinn ☺️☺️☺️
What a great view you have why you're working on your cars
I know right , it’s like a painting that’s constantly changing 🇦🇺🇦🇺
ICE Ignition. Good choice.
Yes it’s easy to install and tune , I’ll be getting myself one in the future 👌🏽
very informative! keep it up mate!
Cheers mate, thank you
I don't recommend it.. you risk to haveedges not flat
It’s got to be 10 times better than it was
I'm sanding my 7m right now I done it with my 2jz a piece of granite slab and sand paper my 2jz runs great I beat the crap out of it
Dunno if youve seen this channel, BanijayEngine, some good stuff. Bad chad is pretty cool too :)
Cheers Jason , I’ll have a look 👌🏽
Great video keep up the good work buddy
Cheers man 👌🏽
Coming a long nicely. Can I ask who folded the seal panels for you? I need some lengths of gutter folded for an old LandCruiser I’m doing and I pass through your way every couple weeks.
I got Port Augusta Steel Center to bend them up for me , same day service and it was less than $200 for both 👌🏽
@@unclebrentsshed4253cheers mate I’ll check them out next week on me way through
Loving this project, all worth it!
Cheers buddy 👌🏽👌🏽
Sill panel, not seal panel.
Oh dang 😅🤦🏻🤦🏻♂️
@@unclebrentsshed4253 All is forgiven. Sorry retired teacher here. Keep up the good work.
Owned quite a lot of VC valiants plus a factory V8 one in 79 /80 . Plus modified VC utes . Why not on the road 🤔.
Iv had a few but I’m more of an ap person 👌🏽👌🏽👌🏽
Hell yeah! Awesome buddy
Cheers brother 👌🏽
It’s great to see some content on the vc! Keep up the good work
Cheers brother 👌🏽
not bad , slants are strong
It’s getting a Toyota 1UZ V8
had something like that in a centura 4spd ,it was fun. these days id put a hho cell on it ,my cars run just that little better like you have a tail wind with hho. towing you dont need to drop back gears as often
Awesome man 👌🏽👌🏽
Nice work Brent
Cheers brother 👌🏽
Fu%& she flys 1 tonne in 1st fu%& she can rev, love it who built the motor
I bolted the motor together in previous videos 👌🏽👌🏽👌🏽
Good video there Brent are you not on Facebook anymore?..I know Jordan is still on there..well hello anyway
Yeah iv been booted from there 😅🤦🏻♂️
Awsome
Cheers mate 👌🏽
Happy birthday mate 🎉
Thanks sir 👌🏽👌🏽
A good start, should be a good project.
Hope so mate 👌🏽
Most of it will buff out the door was straight as was the front left guard till the other car came out from nowhere and hit it
Yes true 😅👌🏽👌🏽
👍🏻🇦🇺
Cheers 👌🏽👌🏽
Ive got a mk2 escort van that needs floors, a hd holden that ive just finished all the rust and getting ready to put back together and a CL valiant thats on its way so i can do more rust repairs. Im soo sick of rust repairs. Happy birthday and i hope you have fun with your projects
Cheers brother , good luck with your projects 👌🏽👌🏽
Great content and filming with the direction of this video, involving fabrication and restoration of the Chrysler linage. Happy birthday, too.
Cheers mate thank you very much 👌🏽👌🏽
Nice mate, welcome to the rust repair period on your VC! I've been stuck in this period for months on the XW haha, cool project man, I reckon 300 bucks Is a bargain.. looking forward to it 🍻
Cheers brother 👌🏽👌🏽
$300 I don't see any wasted money there!!! Happy birthday ! Whats happing with the pacer build ?
Cheers mate , im thinking once this is done I’ll do some pacer stuff in between the charger , Phoenix , ap6 , and the new project I just acquired 😅🤦🏻
@@unclebrentsshed4253 sounds good mate ! I like all your projects going on hahaha did you shut down your fb account ?
@@1979mjcarter NO IM current on ban at the moment , not sure exactly what i did wrong lol
@@unclebrentsshed4253 bloody fb done me a few times too grrrr
Happy birthday 🎉 we're a long way away, or I'd give you a party.
Haha cheers , that would have been awesome ☺️☺️
Happy Birthday ol fella 🍻
Cheers brother 👌🏽👌🏽
Had aVH pacer 265 with a 465 4brl went very well big car lots of fun
That would have been awesome 👌🏽
Great video mate.. what a experience to see bat out of hell in the bush driving.. keen to go myself next year .. how far were you guys camped out from alice springs??
About 65kms not far from where they crossed the main dirt road 👌🏽
I recon those 2 extra barrels on the 465 cmf came in handy.
Haha most definitely 👌🏽