5:50 “I’m telling you… he’s cool, he’s good looking, he’s coming for our job. I’m gonna spread a vicious rumor about him. The mullet’s fake” 😂😂😂 man these guys are the best
Then you have never seen the INCOMPARABLE Rich Rebuilds. Richie B. Kidd is the quickest, cleverest, most brilliant host/comedian/engineer of any car guy on YT.
Honestly, the most inspiring part of this channel is how you've integrated ads into the video. Everyone should be looking at ya'll for how to make an ad worth watching.
If your tire comes off the bead you can also use a ratchet strap around the tire in the middle to make it seal against the rim and air it up that way. I learned that from my Grandfather when I was a kid growing up on a farm. He used to do it on tractor tires. It works on any tire with a substantial sidewall. I've personally done it on tractors, lawnmowers, and off road tires 👍
Well, the problem is Z06 is not a cheap car to buy and even if you can find them on high mileage, its still expensive to bought. '04 Corvette Z06 price is about >30k USD on most car sales and thats on above 30k mileage. IF you can found less than 10k mileage, the price will be on 40k range while the brand new car is on 50-60k back in 2004. If you guys saying I am defending them for unfair sabotage, think again. Why they will give you an expensive used car easily unlike previous one??? Used 350Z, C10, Integra or Subaru are much easier to find them below 10k while used Corvette Z06 '04 starts from 25k USD which already 2-3x times more than their budgets. Even most challenges on TV show always doing like that when the stakes are high, they dont want lose the profit or else they will bankrupt after airing for few months. This is the reality of our world, we will cheat when stakes are high while on low stakes we let them win.
Right! 4 months of snow and freezing another 4 months of rain and if you’re lucky 3 months of decent weather with 1 month that feels like a drought. In northeast Ohio anyway.
Awesome content, well done Randal. I have seen countless offroad axle changes on UA-cam, mostly on 4WD 24/7 so I figured that was a job I could tackle on my own outside my house. Within 20m of all of my tools, on solid ground and with an entire day... I couldn't get the lower ball joint to separate. My ranger has torsion bars on the front, they were forcing the lower control arm upwards into the hub. With hindsight I should've realised this was the problem, but I spent nearly 6 hours and still couldn't get it done. I am going to have to get a lot better at bush repairs before I even try any solo trails
This made me so thrilled & filled with anxiety through the roof! I just finished replacing my U joint, drive shaft, & rear drum rotors & brakes on my 98 3rd gen 4runner. She drives as smooth as butter. I’m moving next to my timing belts & tensioners,then smooth sailing into putting a 3 inch lift & a whole new light bar on her. Cheers gents!
Love the video. very interesting to watch. This video is actually a good reason why you don't use the flammable trick to seat a tire, it is just not reliable and can cause more problems then it solves and is a last resort when you don't have access to an air compressor. In my years of working service truck I have found that 80% of the time you can just do what they did and shift the tire on the rim and make a seal. When that failed I switched to something we called murphy's grease, a thick vegetable grease that you shove in all the cracks to make a seal. It makes a mess, but can be re-used and always works.
@10:50 As a former firestone technician he's doing it wrong. You need to push the tire down and wet the rim. One quick once around and over the tire. He wasn't getting anything combustible inside of the tire itself. Therefore there was no explosion to be had.
DONUT MEDIA Make it so Donut staff have 1 week to make a gokart and in the end to race. you choose the budget IVE BEEN DYING to see something like that
3:05 "Really easy to get locked in that first thing you think of." Dropping random life wisdoms in the middle of offroad-recovery. Needed to hear that!
Love these episodes outdoors. It requires a lot of dedication on the hosts, camera team, and other employees though to be in the hot California sun. Thanks for suffering through it to give us this awesome episode.
Their mistake would’ve been letting me get it unstuck with their truck. I would have absolutely sent it, full beans, haul the mail, entire enchilada. And cooked it up that hill.
@@randallschank3566You were beating the crap out of it lol. I dont know about the KC lights getting done on time tho…that looked staged, you didnt even look close at 3 min left. Ohh well, sweet truck.
@8:05 - precisely why you should *always* put a blanket or towel over the cable when winching. If that thing snaps back it could seriously damage one of the vehicles or worse a bystander.
4:30 Donut staff : Randall, you're aware of the safety concerns with disconnecting the sway bar under load, right? Ronald : Very, Yea im a stabilizer design engineer
What a freaking fun video!!! I have to point something out. I am not an off-road enthusiast and I knew nothing about KC Lighting. They made such a fun commercial that I didn't even skip it. Edit: Spelling 😅
As an avid Jeep guy learning to pick a line and stack rocks is an art form. I’ve never had a spot I couldn’t get my Jeep through or out of with critical thinking. But being under a time constraint makes this incredibly hard.
So I needed a new tie rod for my ole BMW and didn't know what it was until watching this video so thank you for saving me from buying a 300$ rack and pinion instead of a 25$ tie rod and also getting me back on the road sooner! Thanks guys!
I used an International short bus as a work truck and stuck it to the axle in a client's yard. I had a bottle jack, blocks and some 2x12s. I dug out a hole on each side of the axle and fully sank two concrete blocks in the muck before it started lifting. I finally built myself a little road across their yard of 2x12s. Sink a sweet campervan or bus next.
He could've still used that anchor if he looped the winch cable thru the base and attached it to itself with the D-ring. He would've had to bury the shit out of it though. I would've tried to do it off the road so it would help pull the truck laterally.
Man I have watched donut for years but you just keep getting better and better and kudos to KC what a sharp move teaming up with you guys. You make me want to work on my cars…and my cars love that!
On my 2000 taco, i did not need to take the brakes off to replace the front CV’s. Took me all day being my first real mechanic fix but it is quite simple and easy once you know how
He could of saved a lot of time by unbolting the ball joint & tie rod assembly from the spindle by taking the 4 bolts out with the impact instead of waisting time trying to separate the ball joint from the knuckle. Doing it this way also frees the spindle from the tie rod so it’s easier to manipulate and get the old axle out/new axle in. This style ball joint on the Toyotas are literally the graviest lower ball joints ever I wish that all suvs and trucks were like that. Ps don’t forget the alignment after that tie rod. You can even perform one in the field with chalk on the tires with a line scribed on them, and use a piece of a wood or a toe measuring stick. 👍🏽 👨🏼🔧 ❤️ 🚙 🛠️
I'm glad Zack piped in cause I was triggered AF by that "easier to get the part off" comment lmao. Up here a simple "bolt on mod" can take a full weekend, 1 day to remove the part, half the next to fix whatever you broke, and the rest to finally install your part.
This is the second time I’ve heard music that I heard first from the distractible podcast in donut media lmao it’s license free music but I love that my two favorite podcasts/UA-cam ppl use the same royalty free music😂
I love the idea of an escape room, but it's a stuck car instead. Reminds me of altogether too many times of desperately digging vehicles out of snowbanks, or trying to push them back onto the road with a group of friends/strangers.
How many more donut videos do I have to watch to be able to fix something like this? Been watching you guys for years and I'd fail this miserably. Cars are -pain- expensive.
What car/truck should we do next?
Obs F-150
Volvo 240
PT cruiser
Zach's S14! Lol, just kidding, but I would like to see that built, maybe another moneypit?? Why dont you guys get an E36 or a 350Z?
@@rickymackie2340i wholeheartedly agree
This is such a good spin on this concept, y'all are killing it lately
This is intense, the donut guys at HQ probably have an evil thinking table. 😂😂
I second this.
I know right? One large advertisement disguised as entertainment. Genius!
Simpin
Agreed
5:50 “I’m telling you… he’s cool, he’s good looking, he’s coming for our job. I’m gonna spread a vicious rumor about him.
The mullet’s fake”
😂😂😂 man these guys are the best
Yeah that was a good one 😂
Jesus loves you & made a way for our sins to be forgiven, turn to Christ & repent for eternity in Heaven!!!
@@God_is_good_alr sure
@@God_is_good_ 666
2:56 Nolan's Dad Stance is impeccable
while also doing dad-like in-person commentary. priceless
Power stance
😂
"Hey, I've got some firewood you can chop back at my place if you want" 🤣🤣
Went to university with Randall, and he definitely had a passion and knowledge for off-roading. Super sick to see him here, glad it went to him!!
Give this guy a job at donut! He can be the resident off roader😂
I think they just got one of those 😅
Seriously! Dude was chill!
I secretly think this whole series is a recruiting tactic 🤣🤣
Please🙏😂
@@randallschank3566 aye, sweet new ride bro!!! And good work!
I think this dude deserves an offer at Donut. Really chill and knowledgeable with the guys. Congrats!
You've got to get all the offorad resucers (Heavy D, Matt's Offroad, Tow Mater, etc.) together to compete for something ridiculous!
And donut should nominate one person to represent them to gain the title ULTIMATE CAR CHANNEL
I notice we kinda using them to make videos for us instead of doing their jobs. Recovery vehicles being used in videos instead of recovering lol.
i've never seen a sponsor segment get worked into the episode so well , its legit got classic game show vibes
Then you have never seen the INCOMPARABLE Rich Rebuilds. Richie B. Kidd is the quickest, cleverest, most brilliant host/comedian/engineer of any car guy on YT.
I didn't even realize that lol
Honestly, the most inspiring part of this channel is how you've integrated ads into the video. Everyone should be looking at ya'll for how to make an ad worth watching.
Ads suck, ads will always suck. Its just a necessary evil.
@@Bombskwad92what the hell is your profile pic dude
It's similar to other game show sponsorships, so nothing new. It would be better if they had the yellow bar on it for us to know when it's over.
@@obeseperson it's superalloy darkshine bro.. never seen 1 punch man?
What do ads have to do with inspiration?
If your tire comes off the bead you can also use a ratchet strap around the tire in the middle to make it seal against the rim and air it up that way. I learned that from my Grandfather when I was a kid growing up on a farm. He used to do it on tractor tires. It works on any tire with a substantial sidewall. I've personally done it on tractors, lawnmowers, and off road tires 👍
Could probably do it with the winch line.
Through the spoke or all the way around?
@@mikej5959 all the way around in the center of the tread
I've had to do this to my stretched tires. When the old guys at work saw me do it to a UPS truck tire, they were like "wtf did you learn that??"
@@travisstamp7428 Yeah I've done it on the trail and people were amazed
Randall killed this challenge! At least he did it. That other guy with the Camaro (I believe) almost had me shed a tear when he didn’t fix it in time
😂 That episode ripped my heart out
Corvette?
Well, the problem is Z06 is not a cheap car to buy and even if you can find them on high mileage, its still expensive to bought. '04 Corvette Z06 price is about >30k USD on most car sales and thats on above 30k mileage. IF you can found less than 10k mileage, the price will be on 40k range while the brand new car is on 50-60k back in 2004.
If you guys saying I am defending them for unfair sabotage, think again. Why they will give you an expensive used car easily unlike previous one??? Used 350Z, C10, Integra or Subaru are much easier to find them below 10k while used Corvette Z06 '04 starts from 25k USD which already 2-3x times more than their budgets.
Even most challenges on TV show always doing like that when the stakes are high, they dont want lose the profit or else they will bankrupt after airing for few months. This is the reality of our world, we will cheat when stakes are high while on low stakes we let them win.
@@hartonosutrisno5452No
Well they did half the work and told him how to do the rest so I'm not surprised
Thanks Zach for repping folks from the rust belt who have to approach demos with a blowtorch and a sledge to get bolts out lmao
Right? Whenever they complain about rust I’m sitting here thinking “that’s not even surface rust”
That part was so funny
Right! 4 months of snow and freezing another 4 months of rain and if you’re lucky 3 months of decent weather with 1 month that feels like a drought. In northeast Ohio anyway.
@@scarbachi2445same for Indiana
I know the feeling here in Missouri. I was going through so much torch gas I ended up buying a bolt buster induction heater.
Awesome content, well done Randal.
I have seen countless offroad axle changes on UA-cam, mostly on 4WD 24/7 so I figured that was a job I could tackle on my own outside my house. Within 20m of all of my tools, on solid ground and with an entire day... I couldn't get the lower ball joint to separate. My ranger has torsion bars on the front, they were forcing the lower control arm upwards into the hub. With hindsight I should've realised this was the problem, but I spent nearly 6 hours and still couldn't get it done.
I am going to have to get a lot better at bush repairs before I even try any solo trails
The fact is scratched up the truck before crossing the finish line is such an off-road thing and I love it
This made me so thrilled & filled with anxiety through the roof! I just finished replacing my U joint, drive shaft, & rear drum rotors & brakes on my 98 3rd gen 4runner. She drives as smooth as butter. I’m moving next to my timing belts & tensioners,then smooth sailing into putting a 3 inch lift & a whole new light bar on her. Cheers gents!
He could have used that land anchor way before he broke it
Turned out good it broke. Had it not broken, he would have been done with 20-30 min remaining, and no drama with the clock running close......
Ya, all you have to do is get it started and then it continues to bury itself as you winch off of it.
@@Psyco913ik it’s like a real boat anchor was annoying me a lil bit
OSHA/Insurance/Producers were never going to let that happen.
Was that the real pull out anchor!???
" I'm a stabilizer engineer." 😂
A 30 min KC light commercial
Love the video. very interesting to watch. This video is actually a good reason why you don't use the flammable trick to seat a tire, it is just not reliable and can cause more problems then it solves and is a last resort when you don't have access to an air compressor. In my years of working service truck I have found that 80% of the time you can just do what they did and shift the tire on the rim and make a seal. When that failed I switched to something we called murphy's grease, a thick vegetable grease that you shove in all the cracks to make a seal. It makes a mess, but can be re-used and always works.
Not gonna lie, the Segway to the sponsor KC lights are so well integrated, it doesn't feel like an ad at all. Kudos to the team for this!!
Day 410 of asking James to do an Up to Speed on his Dad
Been here for a while and I love the dedication
keep pushing man, maybe 1 day
Then post malone
Please do this video 😂
Day 410 of liking this comment
@10:50 As a former firestone technician he's doing it wrong. You need to push the tire down and wet the rim. One quick once around and over the tire. He wasn't getting anything combustible inside of the tire itself. Therefore there was no explosion to be had.
That's one of the best looking 3rd Gens I've ever seen. And it's in Imperial Jade Mica? Damn, lucky man
its even a limited. and im not very far the video in but if it had a factory it would be "Cremé de le cremé"
DONUT MEDIA
Make it so Donut staff have 1 week to make a gokart and in the end to race. you choose the budget
IVE BEEN DYING to see something like that
You usually just have to mount it from behind to get it unstuck. Happens all the time on the internet.
what are you doing, stepdriver??!
@@RD-zf3yb "Mechanic, Johnny Sins, at your service."
hahahahahahaha
@@AlphaFoxAdam*at your cervix
@@brandonberner5467 touché...lol
3:05 "Really easy to get locked in that first thing you think of." Dropping random life wisdoms in the middle of offroad-recovery. Needed to hear that!
Love these episodes outdoors. It requires a lot of dedication on the hosts, camera team, and other employees though to be in the hot California sun. Thanks for suffering through it to give us this awesome episode.
It's SoCal. They're probably about 3 blocks away from suburbia and a 7-11.
Their mistake would’ve been letting me get it unstuck with their truck.
I would have absolutely sent it, full beans, haul the mail, entire enchilada. And cooked it up that hill.
“We got to spread a vicious rumor about this guy……..the mullets fake!” Hahaha 😂
Made my day 😂
this is Mrbeast level edit and writing! including the KC ad placement! keep it up!
Absolutely love this offroad spin on the challenge. This 3rd gen 4runner is probably the best giveaway so far!
Man Randall is such a cool dude, calm and entertaining at the same time, really glad he could win it!
Yay more offroad content! You love to see it, and congrats to Randall!
I'm proud of you guys for not burying the key in 3ft of sand as the starting challenge. 😅
Awe man...i felt some production on this one. The land anchor woulda worked if they didny tell him to axe it in half.
Breaking the anchor was all me lol, I was trying to get it solid in the ground but it was pretty poor metal. Can confirm that part wasn't staged
congrats on the truck my friend@@randallschank3566
@@randallschank3566You were beating the crap out of it lol. I dont know about the KC lights getting done on time tho…that looked staged, you didnt even look close at 3 min left. Ohh well, sweet truck.
@@randallschank3566awesome job! 👍
@@randallschank3566Congrats man nice work. But why did they pause the timer so much it made it seem like they gave you extra time on many occasions?
So happy he won it, seem like a super cool dude who's gonna use it to its full potential. Can't wait for more!
His confidence radiates! Just having fun, solving a puzzle, being a nerd. Hey Randall, how you doing?
@8:05 - precisely why you should *always* put a blanket or towel over the cable when winching. If that thing snaps back it could seriously damage one of the vehicles or worse a bystander.
I think we need him on the show. He's smart. Ramchargers.
4:30 Donut staff : Randall, you're aware of the safety concerns with disconnecting the sway bar under load, right?
Ronald : Very, Yea im a stabilizer design engineer
What a freaking fun video!!! I have to point something out. I am not an off-road enthusiast and I knew nothing about KC Lighting. They made such a fun commercial that I didn't even skip it.
Edit: Spelling 😅
Not hank from king of this hill🤣 bahhhaaaaaa 17:35
I wish there were more up to speeds. I believe that's the show that got me watching donut
I still miss our car dad with the original science garage
As an avid Jeep guy learning to pick a line and stack rocks is an art form. I’ve never had a spot I couldn’t get my Jeep through or out of with critical thinking. But being under a time constraint makes this incredibly hard.
That guys is def gonna be a good owner to that truck! Well deserved victory.
5:35 that line didn't age so well
Very nice of y’all giving cleetus a chance to win the 4Runner 🙏🏽
So I needed a new tie rod for my ole BMW and didn't know what it was until watching this video so thank you for saving me from buying a 300$ rack and pinion instead of a 25$ tie rod and also getting me back on the road sooner! Thanks guys!
Best episode ever,. Glad the dude got it done.
My favorite part about the concept of this show is how the new owner definitely knows their car as they drive away and won't get any surprises
I'll take more of these and the ones with just fixing the car. Super interesting to watch.
I want to see my dad do something like this. The guy deserves to show his talent and have a nice ride along with it.
I've had a sway bar link snap on me when driving after a strut job. When he did that, ALL my fear came back from that day lmao 😂
Got a little addicted to my gun collection and neglected Donut so I have a bunch of new videos to watch. Win-win in my book
Matt from MORR has a saying that if you got out with traction boards, you were never really stuck
I used an International short bus as a work truck and stuck it to the axle in a client's yard. I had a bottle jack, blocks and some 2x12s. I dug out a hole on each side of the axle and fully sank two concrete blocks in the muck before it started lifting. I finally built myself a little road across their yard of 2x12s.
Sink a sweet campervan or bus next.
First thing, call Matt's offroad recovery
Before you get there tho
Southern Utah is a lot more than a 2 hour drive away.
He could've still used that anchor if he looped the winch cable thru the base and attached it to itself with the D-ring. He would've had to bury the shit out of it though. I would've tried to do it off the road so it would help pull the truck laterally.
Would not have made as interesting video though. If that was scripted nice job producing another great video
@@cshader2488Randall himself replied to another comment saying that part was all him being an idiot, no scripting required 😂
This is a great idea, and starting off with the only V8 4 runner ever made, incredible!
Its a V6. V8 is 4th gen
If you can get this truck unstuck (while we help you) you keep it
Randall is A G Dude
We need him in more videos
I wonder if they ever reconnected those rear tie rods
Those are optional
I thought those were the sway bar links?
@@Cavemanner probably were im just dumb alot of the time
if he was an engineer he would have known that disconnecting the front sway bar instead would have given him greater flex
being from Canada, when Jobe piped
up after the boys said putting new parts in takes longer, i felt that in my soul
why did he use the hammer so many times
Man I have watched donut for years but you just keep getting better and better and kudos to KC what a sharp move teaming up with you guys. You make me want to work on my cars…and my cars love that!
"urrrrrm actually is jade green get it right" -Every 4runner owner
Actually it's imperial jade jacmaca green bean green 🤓☝️
@@PugJudge urrrr mit green color like green grass 🥸
Bro won the best truck Toyota ever made! Congratulations man!!!
when he hammers down that anchor, he really doesnt know how to use that, but, he saves himself as a mechanic, hes really a mechanic guy.
"do you understand the risks behind disconnecting a swaybar under load?" "I'm a swaybar design engineer". Best comeback ever.
Glad hanging with the Matts off-road recovery team got us some good content ideas
I have one of those 4runners, blew the cv a few times. takes 10 minutes to replace, so easy to do!
Respect for not lighting up the tire in the desert! Us Wildland firefighters been working tirelessly
On my 2000 taco, i did not need to take the brakes off to replace the front CV’s. Took me all day being my first real mechanic fix but it is quite simple and easy once you know how
Just a note for safety, you can put sand bags or something heavy on the cable to keep it close to the ground instead of it whipping all around.
Should bring over a rust belt vehicle. Now that would be a fun episode to watch. Breaking out the torch, sawsalling off bolts 🤣
This guy 100% deserved it! Great spin on the already existing concept guys 👌🏻
Like Matt says, if the traction boards work, you weren't really stuck. (And since he was, they were never gonna)
He could of saved a lot of time by unbolting the ball joint & tie rod assembly from the spindle by taking the 4 bolts out with the impact instead of waisting time trying to separate the ball joint from the knuckle. Doing it this way also frees the spindle from the tie rod so it’s easier to manipulate and get the old axle out/new axle in.
This style ball joint on the Toyotas are literally the graviest lower ball joints ever I wish that all suvs and trucks were like that.
Ps don’t forget the alignment after that tie rod. You can even perform one in the field with chalk on the tires with a line scribed on them, and use a piece of a wood or a toe measuring stick. 👍🏽 👨🏼🔧 ❤️ 🚙 🛠️
I´m happy Randell made it. He deserves it and this great new truck will do him just right! 😄👍👍👍
You guys are killing it!!!! This episode is pure gold 👏🏽👏🏽👏🏽 keep with the good work guys 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥
this video is a perfect example of how the simplest method will work best & take ur time & think so act carefully in emergency’s
The extended built in Ad really killed it for me and I tuned out. This seems to be happening a lot more, with the baked in Ads.
Bro these guys are on top of their shit! Literally top 5 on the internet
On behalf of all my fellow 3rd gen 4Runner owners, I'd like to welcome Randall to the club! This guy belongs here.
I'm glad Zack piped in cause I was triggered AF by that "easier to get the part off" comment lmao. Up here a simple "bolt on mod" can take a full weekend, 1 day to remove the part, half the next to fix whatever you broke, and the rest to finally install your part.
LOVE DONUT MEDIA OFFROAD CONTENT!
Must be nice no rust, lol that axle would take me 15 mins to take but up here in the north its like an hour 🙃
This is the second time I’ve heard music that I heard first from the distractible podcast in donut media lmao it’s license free music but I love that my two favorite podcasts/UA-cam ppl use the same royalty free music😂
This shit made me smile. I love it. Teaching younger generations to work on they own shit the fun way
I love the idea of an escape room, but it's a stuck car instead. Reminds me of altogether too many times of desperately digging vehicles out of snowbanks, or trying to push them back onto the road with a group of friends/strangers.
The Music right at the end at 20:44 is Bandana by Ballpoint if anyones lookin for it 👌
When an engineer does something they KNOW they shouldn't do, that's prime youtube right there
How many more donut videos do I have to watch to be able to fix something like this? Been watching you guys for years and I'd fail this miserably. Cars are -pain- expensive.
Tip from Australia, use a synthetic rope on the winch and soft shackles. They’re lighter, easier and plenty strong
That dude was so calm. I’d been rushing around and beans it all. The way up there.
2 tone color job would be the ultimate “bubba truck” blue and white.. very nice truck.. 👍🏽👍🏽
This dude destroyed this challenge. Good for him, he’ll actually use the dam thing 👌
Not only are the videos fun to watch, but you guys are obviously having fun in the process. Make more videos plez
👍👍👍 for the Wire reference! Great video as usual. Add this dude as a guest host.
Gotta love how such a famous company sponsoring y’all! Even though it’s after many many many crazy cool deals with cool companies! Keep ‘em coming!