Oh I'm sorry I thought I saw a Creality KE Neptune 4 Clone with and M5C head putting down a print on a Bambu Bed. My Bad I must have been mistaken. No wonder it prints so well. Nice Video And Print.
Nice printer, I bought it too... do you have any cura profiles for the printer? I have seen some have it on there micro sd that is coming with the printer, but mine was empty.
I cannot get the filament to stick to the bed. The first level of print goes down and then starts moving while the second level goes. I have tried everything and still does not work. Been trying to print the test boat for 3 days now. I am very new to this printer (used a Tina2S previously) so I do not know what the issue could be and there does not seem to be any trouble shooting information out there. Can you help me?
The X3 plus is my first printer and there are a few things that really have me confused about it. 1. Is there a 110/220 voltage switch on it? I have looked high and low on the base for one. 2. The bed has 6 leveling adjustment wheels, one at each corner and two at the center of the bed sides. I'm just not sure what those two adjustment wheels are for. My X3 plus didn't come with a micro SD card but with a Flash drive along with a micro-c adapter cable which is OK with me.
Yes it is louder. The fans are louder, in the power supply and the part cooling fan. To print so fast you do need better cooling. Add the high speed motion to that and you're not going to be watching TV or talking on the phone right next to this printer like you can the X1 and X2. This is the same with the Bambu printers. I know because I have one. High speed printing sacrifices quiet, and these printers are running quiet drivers.
@@rburks many thanks for your answer. I was thinking buy one. I also have a X1 carbon and yes, it isn’t the quieter printer but it is closed which reduces the noise. But bambus printer are 3 to 5 times faster than a x1 or x2 (I also have both). I don’t know if these new models from artillery are valuable for the price versus speed in comparison to other printers like elego or Bambu. Best regards
brother una pregunta? sabes si el artillery x2 y x3 plus son del mismo tamaño y capacidades similares? quiero comprarme mi primera printer 3D pero no se por q plataforma comprarlo. En un primer momento quise la ARTILLERY x2 pero me dicen q ya está dejando de ser producida pese a ser "moderna". Donde compras tus impresoras? Tmb soy de Perusalem.
Did you do anything to prep the bed? I have tried the 3DBenchy print twice and both times it broke loose from the bed and started sliding around. 25% the first time. I used a glue stick and got to 85% the second time. So far, I am using the sample filament that came with it since the filament I ordered hasn't arrived yet.
This is exactly what should be done, but I don't remember anyone telling me that on my first printer and I remember struggling back then. It seems like it should be pointed out that those are necessary first steps. I have a few X2's that have basically been trouble free. I almost pulled the trigger on the X3 but then found out they already have an X4 with wifi connectivity. So I decided to wait for it to be officially released. @@deervalleyengravings3088
I also had the benchy come loose two times, and my bed was perfectly level and my z offset was good. Everything else I've printed so far has stuck very good to the bed. I happened to have some VisionMiner NANO Polymer Adhesive that I haven't tried out yet, so I put some on the middle of the bed and was able to finish the benchy without it coming loose.
What did you do to solve the bed wobble. I did turn the eccentric nuts all the way to the iside part but tthere is still some wobble on the bed. I did remove the heat bed as well to double check that the eccentric nuts are all the way inside.
What did you use to clean it? This is my first 3D printer after using an X2 at the school I teach a few times and I know I still have a lot to learn. The X2 has a glass bed and I saw somewhere you can clean it with acetone. Is that safe on the PEI platform? Thanks for answering these questions. This model is still new enough there's not a lot of information out there. @deervalleyengravings3088
Good Video! Please more about the printer.
I will as soon as I play with it more.
Oh I'm sorry I thought I saw a Creality KE Neptune 4 Clone with and M5C head putting down a print on a Bambu Bed. My Bad I must have been mistaken. No wonder it prints so well. Nice Video And Print.
Nice printer, I bought it too... do you have any cura profiles for the printer? I have seen some have it on there micro sd that is coming with the printer, but mine was empty.
Shoot. Mine did come with the profile.
Mine didnt have the actual profile. It came with an older version of Cura it is in it after you install it.
I cannot get the filament to stick to the bed. The first level of print goes down and then starts moving while the second level goes. I have tried everything and still does not work. Been trying to print the test boat for 3 days now. I am very new to this printer (used a Tina2S previously) so I do not know what the issue could be and there does not seem to be any trouble shooting information out there. Can you help me?
Bed leveling is where I would start first. Also be sure bed is clean
The X3 plus is my first printer and there are a few things that really have me confused about it.
1. Is there a 110/220 voltage switch on it? I have looked high and low on the base for one.
2. The bed has 6 leveling adjustment wheels, one at each corner and two at the center of the bed sides.
I'm just not sure what those two adjustment wheels are for.
My X3 plus didn't come with a micro SD card but with a Flash drive along with a micro-c adapter cable which is OK with me.
The two center wheels are basically for bed rigidity. It is more to keep the bed flat than for tramming the bed.
Hi, I was thinking buy it but it seems do more noise then X1 and X2, it's true? In your video it's seems very quiet. Thanks
I think it's louder.
Yes it is louder. The fans are louder, in the power supply and the part cooling fan. To print so fast you do need better cooling. Add the high speed motion to that and you're not going to be watching TV or talking on the phone right next to this printer like you can the X1 and X2. This is the same with the Bambu printers. I know because I have one. High speed printing sacrifices quiet, and these printers are running quiet drivers.
@@rburks many thanks for your answer. I was thinking buy one. I also have a X1 carbon and yes, it isn’t the quieter printer but it is closed which reduces the noise. But bambus printer are 3 to 5 times faster than a x1 or x2 (I also have both). I don’t know if these new models from artillery are valuable for the price versus speed in comparison to other printers like elego or Bambu. Best regards
Que slicer usas para la X3?, ya tengo la mia, pero no se cual slicer usar. Gracias
brother una pregunta? sabes si el artillery x2 y x3 plus son del mismo tamaño y capacidades similares? quiero comprarme mi primera printer 3D pero no se por q plataforma comprarlo. En un primer momento quise la ARTILLERY x2 pero me dicen q ya está dejando de ser producida pese a ser "moderna".
Donde compras tus impresoras? Tmb soy de Perusalem.
@@submarinodeaire2127 hola, son el mismo tamaño la X1, X2 y la X3 plus
English please
@@deervalleyengravings3088Which slicer do you use for the X3?, I already have mine, but I don't know which slicer to use. Thank you
I used one that came with machine untill I can make a profile in another slicer.
Did you do anything to prep the bed?
I have tried the 3DBenchy print twice and both times it broke loose from the bed and started sliding around. 25% the first time. I used a glue stick and got to 85% the second time. So far, I am using the sample filament that came with it since the filament I ordered hasn't arrived yet.
I cleaned it a couple times. Did Z offset first. Then manually leveled it. Then did the automatic leveling. That's it
This is exactly what should be done, but I don't remember anyone telling me that on my first printer and I remember struggling back then. It seems like it should be pointed out that those are necessary first steps. I have a few X2's that have basically been trouble free. I almost pulled the trigger on the X3 but then found out they already have an X4 with wifi connectivity. So I decided to wait for it to be officially released. @@deervalleyengravings3088
I also had the benchy come loose two times, and my bed was perfectly level and my z offset was good. Everything else I've printed so far has stuck very good to the bed. I happened to have some VisionMiner NANO Polymer Adhesive that I haven't tried out yet, so I put some on the middle of the bed and was able to finish the benchy without it coming loose.
@@rburksjust start dropping your z offset by.02 at a time till it gets a solid stick
What did you do to solve the bed wobble. I did turn the eccentric nuts all the way to the iside part but tthere is still some wobble on the bed. I did remove the heat bed as well to double check that the eccentric nuts are all the way inside.
When I took the bed off I was able to tighten the bolt up a little. That seemed to fix it.
This things hauling ass
It have self levelling and wi fi ?
Yes auto leveling no WiFi
Do you recommend me to buy X3 Pro or X2?
I have not hard either of those printers. The x2 does have larger print bed.
Is it possible to use the M600 command?
You can do that on the touch screen
But is it possible to do it during a print? Can the car start again?
What did you use to clean it? This is my first 3D printer after using an X2 at the school I teach a few times and I know I still have a lot to learn. The X2 has a glass bed and I saw somewhere you can clean it with acetone. Is that safe on the PEI platform?
Thanks for answering these questions. This model is still new enough there's not a lot of information out there. @deervalleyengravings3088
I use glass cleaner, acetone, or rubbing alcohol