How To Remove Rusted on Lawn Tractor Wheels
Вставка
- Опубліковано 2 лип 2017
- Today I show you how to remove a seized or rusted on riding mower or lawn tractor rim from the axle, this can also apply to older gokarts with splined or keyed axles. MTD mowers have a bolt that holds on their rims with a unique axle that has a sorta square shape with two sides that are rounded and they use their own proprietary wheels.
ride on go kart gokart gocart golf cart lawn tractor axles rust - Розваги
Mine was frozen bad, tried a puller, tried your method which was good, but still would not budge. I went back to my old bag of tricks that I used on other things like blower wheels and blower motors. The secret is to first knock it on further(which brakes it loose) then take it off. Take a piece of 3/4" ridged pipe(black Iron or galvanized) 2 or 3 feet long. It will fit over the shaft on the outside of the wheel. Hit it hard with a sledge and knock it in an 1/8 of an inch. That's it, not froze anymore, now use a puller or your method and it comes right off. Hope this helps someone with a really hard one to get off.
Finally!.. someone smart enough to remove the rust from the axle BEFORE mounting the rim back on.. good job!!
You did a GREAT job showing us how to remove & re-install the rear tire. I Give you a top 5 stars for making it easy to see & follow your instructions!!!
Thanks you 76hotrodF250. It worked with a few modifications. I have one of those MTD tractor since 1999. Time to replace the rear tires and get it ready for hurricane season. So I did not know what I was getting into until I started pulling and hammering at the tires. They would not come off. I blasted it with WD40 and nothing. I ran into your video and tried the heating trick but with a less tame propane torch. One wheel came off easily the other was was stubborn a a mule, but it gave away after some muscle with a jack hammer. keeping those videos coming I am sure there are a bunch of us out there with similar problems. thanks, save my Sunday afternoon. Cheers from Land O lakes Florida!
This is the best video I've seen about this problem!! Thanks alot for sharing with us! God Bless and stay safe!👍
Thanks for your educational videos. I am going to apply the same technique for the stuck wheels of a snow blower.
Thanks again.
This video helped with my snowblower tire. Thank you for this.
You’re video helped me a lot. It show me I was doing right. I’m always afraid I’m missing something. The first time try something new. Thanks.
The rear wheel on my Husqvarna Lawn tractor was frozen from rust. I beat on the rim for a week and the rim didn't even budge. I tried this method and it worked. I had to heat the hub several times and I put Liquid Wrench on the hot hub. Thank you for doing this video. Clint
Drrẞ4àD44444144414444144444444441444444144144444444144141444444
Great video, wish I was young enough to do all that..but I sure understand alot more then when I started...THanks so much
I enjoy watching all the different ways people work and what they do
Thank you! Great informative video. I have a Simplicity 560 snowblower that I bought used and now I need tube in both tires. I will use my Acetelyne torch to try this method.
Mine was super seized.
I ended up spraying PB blaster every day twice a day for a week.
I ended up tipping the tractor so the affected wheel was higher than the other side and left it propped up like that until Two weeks were up…this helped the penetrating oil deep further down the shaft with the aid of gravity.
I ended up using a harmonic balancer puller to break it free without the aid of heating with a torch.
What kind of puller? How did you mount it?
Great instructional video. I have a Toro snow thrower that has a stuck on rear wheel. I'm trying the WD40 trick first but if that fails will likely have to resort to using heat from a torch. Excellent comment btw on removing the wheels annually and servicing them. Wish I had known about removing the wheels and servicing regularly.
Good job dude, I especially liked the FIRE FIRE FIRE !
Yep like the way you start your vid I feel the same way when you want to do something and you have to to do something else to get to that something you were suppose to do cause everything is jamed in rust , torches are the best at a lot of things . have a nice day
Thank you Mr. Dirt .. I hope to see you in Silvertown someday
You really did a great job.Thanks. I will give it a try. Hard work always.
Cut the Tire, put a new one on... Better than sitting there all day for $32.00
I removed my rusted rear wheel on my John Deere with WD-40 and banged the rim with a heavy duty hammer, for a minute( had a new rim and tire to replace)...Then I hit it from the backside and it came off, an easy piece😅. Not everyone has that equipment, however the knocking part you showed gave me direction.,.so ty for that.😊
Great common sense approach to a difficult task.👍
Excellent work Beavis!!😉👍
Thanks for sharing your knowledge, I needed to see your video.
Another cool video my friend. I know you don't mess with lawn tractors much anymore, so its a treat to see them here! Seeing this makes me glad I have garden tractors (Deere 318 and 445) with bolt on hubs instead of shaft mount! Whatever you do, I'll watch. I hope someday you decide to kill another pushmower though lol.
Thanks, I just like to mix things up a bit, and its helped a lot. I am actually starting to like working on them again but years ago it got stale because thats all I did. My Dayton has 5 lug rear wheels but everything else is shaft style. I am hoping to kill another pushmower as well I just gotta get one I don't like haha.
Did the same. The JD 318 is a REAL machine in comparison to the Craftsman. Gave up trying to pull the Craftsman's and just changed the tires while on the shafts.
Thanks for the "how to video" 76hotrodF250, the oxy acetylene was my next move but I didn't think to heat the inside. Great tip!
The first thing you should do when you get a riding mower , is pull the wheels off and put never seize on the axels. Do this and you will never have this problem. Most people don't do it .
*CUT the Tire, put a new one on... Better than sitting there all day for $32.00 :/*
I wish I did
Thanks for taking time to make this. Lot of good tips.
Thanks for your help it help me alot
At the end of your video I heard you mention the bolt attachment method used on the MTD...... I have a Troy-Bilt which is made like the MTD. My rim is stuck, which is why I watched this video. Oh boy am I in for a fun time.
Great video on how to use heat!😀
2 things:
1)Tireject will fix the tires.
2) Air chisle with a blunt bit on the axle will get the wheel moving. If you do the heat thing, quench with a water hose.
Rotiller wheel 40 years old. Used the heat and penetrating oil, also took the tire off the rim and used both methods to get wheel off. Took quite a bit of pounding. Axle had no rust and inside of wheel had no rust. I will generously lubricate the axle with never seize. The other wheel came off easily with just penetrating oil.
Great video, Thanks for your "HELP" !!!!!!!!!!!!!!!!!!!!!
Try a Cold water quench immediately after heating. Centre punch centre of Axle and use air impact chisel with pointed bit. ALWAYS air down the tires when removing rims.
Enjoyable ! Thanks for the good instructions …
Try using Hot / Cold Method! Wheels will come off easily for you!
Fire,, Fire 😂😂😂 good show sir..
I know about mtd wheels. I have repaired the transaxle with one or both wheels still attached. Just put on blocks then slit the case. Most of the time the bushings ware out which give the gears more Clarence.
Well. done, thanks so much!
Very informative and entertaining! I was chuckling a bit while watching. A little censoring may have been needed for me doing this video.lol! Thanks for the video!
this is a very good information video thank you
Am dealing with a seized wheel on a 1988 Honda Harmony HT-R3009 riding mower. Had tried a couple methods seen on UA-cam without success including PB Blaster over 2 days. Only have a propane torch but will try it and hope that works. Good video.
John Kohler I had one of those old 3009 Honda riders years ago, good mower but mine smoked bad on startup so I sold it while it was still running. Heat is the best option for removing stuck wheels, a propane torch should be enough to get it plenty hot. You might even try quenching the heat afterwards with cold water to make the axle contract a bit but don't get it on the rim. Heat expands Cold retracts.
Good job. Now I know what to do.
Good tips. Thanks
Fits perfectly.
Great job
Thanks for the video I have the same tire on a similar lawn mower amazing. Now I know that I was on the right track thanks for the advice.
Thank you good Job
excellent advice on the re-installation of the tyre. I was unaware how to get the C clip back on.
Very helpful thanks
First words makes me laugh 😂😂 at the way u said,and thanks a lot with the video helps me out...
All the blaster is doing is cooling fast ! Breaks away from Rust ! Water hose would work better ! Good job though
Great info! I've had some that I had to cut the wheel off.
Thank you!! Yes I have had to cut a few off myself.
Just a great video- you’re no slouch😉
Thanks bro!
WELL DONE !!!!!!!!!!
A hand-held belt sander with 220 - 300 grit and rotate the shaft as you take off the rust will make a fast job; I just use a sheet of 220 grit washable sanding Cloth is great too and grip the shaft and rotate as you sand.
Thanks a lot .. I watched you... started beating on the back of the hub... broke the retainer clip inside the transmission.... now I'm really screwed ...n Thanks a bunch.. i should have known better than watch shade tree mechanics on Fube Tube
Great video, now all I need is a torch! Ha ha ha
Keep teaching us.
Thanks for sharing
Nice info
Wow! I've heard of people junking perfectly good running mowers over not being able to get the tires off that needed replaced!
Happens all the time.
Busted the spiral retaining ring off the axle shaft trying this exact method. Now I've gotta mow making only left hand turns or the axle slides out of the gear box 😄
Lmao time for magic spot welds
You are an excellent teacher!!!!! Thank you.
thanks a lot. hope I will get mine off, will let u know.God bless
Did it work
Thank you
Thank you 🤙🏻🤙🏻🤙🏻
HEAT thank you
nice vid.
Thank you sir.
This video helped me, thanks
How long did it take? The transmission was ok with the heat?
Great video, but the pounding with the hammer and bar can damage the transmission and then you'll have more problems!
Good video thanks. At 5:06 I thought a bald friend showed up to help but I was wrong.
Lol
How did you get the lugnut off.i can’t get mine to turn and come off so I can take the tire up to the shop and repair it
Hi...I found a big wheel.not a plastic one a metal one.I'm Gunnar combine it with a scooter problem is the rear tires.can't get the bolt off.its on there good.I've hit it tried to pry it.even heated it up.shot won't budge.can you help please?
I have the exact same mower and tried to do exactly what you did. The axle came out with the wheel. Still can't budge it. Got a follow up video for heavy-handed grease monleys with heavy hammers like me?
I guess now I need to rebuild the axle too, or is it too far gone if it comes out like that?
Unfortunately the axle coming out is a problem that happens and I warned of that in the video and it has happened to me a few times. I don't have any rebuild videos but search up Lynols office he has a rebuild video on transaxles.
You can damage the transmission case by banging on wheel . Drill, and use a puller, after heating .
There are holes already in the rim to use a puller with. Heat the hub, quench with cold water and use the puller. If it doesn't move then use an air impact chisel with a flat end bit on the end of the puller. Always worked for me. Then put never seize on the axle when reassembling. Won't have a problem next time wheel has to come off. And, yes, you're right about possibly causing damage by beating on it with a big hammer.
thx!
Damn fine job! Your next video, " how I use my weed eater".
Bent my rims and then the transaxle differential broke a year later from the beating. Wheels are still stuck on both my axles and I now need a trans. I had the double flat axle.
After cleaning thoroughly using anti-seize is definitely the secret.
Everyone tries to heat the whole wheel boss. A mad old timer metalsmith once told me Its actually more effective to heat in a streight line over the keyway and expand it like a clam!!
A Dallas Fan.... ok, thumbs up it tis
Try Candle wax instead of Blaster. Works better. it soaks in really good.
What is a slide hammer puller design..something like that work better than the sledge driven pipe? Don't know, only trying to think
thats the longest cap ive ever seen lmao
Metal hammer against metal pole, also wearing safety glasses is a good practice.
FIRE FIRE !
That tire actually inhaled air when when you pulled the shrader.
I laughed with you when you said, "Don't lose the key either."
I wrestled with mine and ended up getting behind the wheel close to center with a 2x2 piece of wood, hit it about 5 times with a 2 pound hammer and it popped right off. No torching !
THANK YOU 76 HOTROD250 VIDEO I HAVE XR75 JOHN DEERE I HAVE SAME HIT WHEEL COUPLE HUGE PRY BAR BEHIND SOAK OIL KEYWAY AROUND TIRE DONT MOVE VIDEO VERY GOOD THANK YOU TIME TOOK SHOW HOW YOU DO IT
quick tip, use an old toothbrush to apply the antiseize, you dont want that junk on your skin, i keep some ready in a ziplock bag with the Permatex tube. Bingo bango!
Heat...we call that the hot wrench..lol
Thanks for the tips and the laughs. Made my day and gave me some hope with this bitch of a tractor.
I tied my transaxle in between two trucks and had them pull on the wheels the rusted on one still did not come off y'all got any ideas
Great UA-cam. Looked to me like the only way to get the wheel off.
You said,,,u cut the wheel apart.,,,,Was it just the tire u cut off,,,,,,or the rim also,,,,,Thanks
Take a 10 inch peace of 1/2 inch rod or bolt, cut slice in it slide Emeny cloth 220 grit and polish inside really helps it slide back on easy
Hehe. I’ve done that before, instead of the wheel coming of, the axle came out of the transmission. Ya, then time to take the rear end out to fix that. I’ll stay with the puller.