I'm planning to do this in the next couple weeks. The one concern I have is if when replacing them, will it effect body panel alignment? Did you have any issues with this? Great video...thanks!
Is it the same process on a second generation big bumper Camaro? The reason I included "big bumper" is because the front radiator body mount is hidden inside the frame and the bumper tubular arms are in the way
Good video, I’m in the process of replacing mine on my 67, it started with doing a clutch and then realized my body mounts were so bad I couldn’t get the trans crossmember out lol. I bought the same brand bushing as you, but I can’t for the life of me get enough clearance to get the middle ones in even with all the other mounts loose, did you have any trouble with middle set? And were did you jack the body up from or how did you get enough clearance to get yours in?
I'm so sorry for the late response I didn't see this in my email feed Yes I loosened all six and then I only took out one side at a time I was able to jack the body up enough to slide it out takes a little bit of time Thank you for watching my videos
I know it;s been 4 years, but I was hoping you might remember the order of the bushings. The core support ones are obvious, but the other two pairs is where I am confused. One pair is thicker than the other pair. Do the thicker ones go to the rear or in the middle? I'm hoping you might remember.
orry for long delay but I did not see your question. I bought these only because of the read and I thought they would provide a better ride. I was wrong. I removed these red on and replaced them with black rubber ones I purchased see other video I have explaining this.
I was just under my car a few weeks ago replacing my transmission mount. Had to loosen my sub mounts and they still look new. Much better ride with stock sub frame bushings.
sorry for long delay but I did not see your question. I bought these only because of the read and I thought they would provide a better ride. I was wrong. I removed these red on and replaced them with black rubber ones I purchased see other video I have explaining this.
The brand is on the box in his video, Prothane.
I'm planning to do this in the next couple weeks. The one concern I have is if when replacing them, will it effect body panel alignment? Did you have any issues with this? Great video...thanks!
Not to worry. Do one side then the next. No movement
Is it the same process on a second generation big bumper Camaro? The reason I included "big bumper" is because the front radiator body mount is hidden inside the frame and the bumper tubular arms are in the way
Good video, I’m in the process of replacing mine on my 67, it started with doing a clutch and then realized my body mounts were so bad I couldn’t get the trans crossmember out lol. I bought the same brand bushing as you, but I can’t for the life of me get enough clearance to get the middle ones in even with all the other mounts loose, did you have any trouble with middle set? And were did you jack the body up from or how did you get enough clearance to get yours in?
I'm so sorry for the late response I didn't see this in my email feed Yes I loosened all six and then I only took out one side at a time I was able to jack the body up enough to slide it out takes a little bit of time Thank you for watching my videos
Did you take all the bushings off at one time, one side, or one at a time to replace them?
Than you for viewing my video. I did once side at a time. Did not tighten until all were in place and resting on the ground
I know it;s been 4 years, but I was hoping you might remember the order of the bushings. The core support ones are obvious, but the other two pairs is where I am confused. One pair is thicker than the other pair. Do the thicker ones go to the rear or in the middle? I'm hoping you might remember.
Great video! Can you post the brand of those bushings or where you got them?
orry for long delay but I did not see your question. I bought these only because of the read and I thought they would provide a better ride. I was wrong. I removed these red on and replaced them with black rubber ones I purchased see other video I have explaining this.
FLIXZONE is a scam
How are the bushings holding up being 4 years old now?
I was just under my car a few weeks ago replacing my transmission mount. Had to loosen my sub mounts and they still look new. Much better ride with stock sub frame bushings.
What brand...
sorry for long delay but I did not see your question. I bought these only because of the read and I thought they would provide a better ride. I was wrong. I removed these red on and replaced them with black rubber ones I purchased see other video I have explaining this.