Perfect processing and design. You certainly put a lot of work into it. Super manageable alternative to mainstream IOT systems which are much more expensive and less manageable. Great work
Really...one of the best companies with all explanations, demos, codes, tutorials etc... transparent and explanied. You mentioned here in video that you will be doing integrayion with home server. I havent seen that :)
An excellent video, thankyou for the openness with your design, so we can easily see how to integrate it with other devices like Home assistant green. Keep up the excellent work with your products!
If i understand correcly basicly digital input is switch on/off and when its pressed ON you enable digital out that sipits out 12v? and with that 12v you control fuse that goes on off based on 12v input?
digital output is relay dry contact output, you can connect with any voltage. INPUT also is dry contact signal , use 0v for trigger, 12V or "not connected" = untrigger.
Nice work! Your design will ignore relay state from controller if some switch is toggled? Is force off possible? I have similar design with manual switches for relays but I use three state ones. This way I can either force on, force off, or set to controller state. For example, I need to check my lightbulb, so I force off one line and I am assured that no automation will power it while I am in contact with wires. After repairs I toggle auto mode back and any state from controller will be applied back. Another use case is controller problem while I need some light somewhere. Then I force on required line and the controller can not switch it off until I allow it manually.
Wow...Feeling happy as a kincony fan. it is a milestone product...i have come queries 1) can I use 1sqmm. copper cable or aluminum cable for DIs. how much distance i can go. 2) can i able to run kcs and tuya and HA software at same time simultaneously, 3) it will if i turn on relay 1 in kcs it will update the state in both tuya and HA. also vice-versa??
Can you make a video with an example use case like turning on some lights or something so we can also see a wiring example and also how to set up light switches in esphome?
Hello KinCony., i have a question. If i turn off switch on board, can i control with HA or orther flatform?. I don’t see switch manual in the schematic. Could you help me locate it ? Thank you very much, have a good day
@@KinCony but if i turn on the relay by the switch on the board then the relay state will only be turned off by itself right? and What is the purpose of the switch on the circuit? I would appreciate your reply
I like your products, I have Clipsal C-bus system , do you have any products that will interface with the Clipsal C-bus system, or have you thought about doing anything in the near future ? Thanks.
Pi not included, if you want work Pi, need another Pi server. if you want to use tuya app, it can directly to use. But we have another product Pi+relay = one board.
You make the best products ! Congratulations on your work and on keeping designs available, and so detail documentation. Congratulations 🎉
thank you.
Amazing design and open source 👏 more companies should be like this
thanks
Perfect processing and design. You certainly put a lot of work into it. Super manageable alternative to mainstream IOT systems which are much more expensive and less manageable. Great work
thanks
Really...one of the best companies with all explanations, demos, codes, tutorials etc... transparent and explanied. You mentioned here in video that you will be doing integrayion with home server. I havent seen that :)
do you means how to use for home assistant by ESPHome?
An excellent video, thankyou for the openness with your design, so we can easily see how to integrate it with other devices like Home assistant green. Keep up the excellent work with your products!
thanks
KinCony fan ❤
still not used your products 😢
I just bought it.. will try it ASAP
thanks
Congratulations on your work ❤
thanks
so happy as kincony fan...
If i understand correcly basicly digital input is switch on/off and when its pressed ON you enable digital out that sipits out 12v? and with that 12v you control fuse that goes on off based on 12v input?
digital output is relay dry contact output, you can connect with any voltage. INPUT also is dry contact signal , use 0v for trigger, 12V or "not connected" = untrigger.
Gratulations this looks great
thanks
this video have re uploaded, today's first video's audio error, thanks for our fans feedback ,so that we can fix it re uploaded the video.
Nice work!
Your design will ignore relay state from controller if some switch is toggled? Is force off possible?
I have similar design with manual switches for relays but I use three state ones. This way I can either force on, force off, or set to controller state.
For example, I need to check my lightbulb, so I force off one line and I am assured that no automation will power it while I am in contact with wires. After repairs I toggle auto mode back and any state from controller will be applied back.
Another use case is controller problem while I need some light somewhere. Then I force on required line and the controller can not switch it off until I allow it manually.
toggle switch control relay's COIN voltage.
If i want to use your product do i have to replace the light button the i am useing
just use by push button: momentary switch panel.
Can some ports can be configured as time based to open / close curtain?
sure, you can use IFTTT command to set timer.
Hi… Can I connect KC868-COLB to this board?
Because I've the old setup of Kc868-H32BS connected by RS232 to COLB
COLB support IFTTT by HTTP command, you can let COLB work with A32 Pro by HTTP.
Wow...Feeling happy as a kincony fan. it is a milestone product...i have come queries
1) can I use 1sqmm. copper cable or aluminum cable for DIs. how much distance i can go.
2) can i able to run kcs and tuya and HA software at same time simultaneously,
3) it will if i turn on relay 1 in kcs it will update the state in both tuya and HA.
also vice-versa??
1. it's ok, 300 meter is no problem, i think 500 meter is also ok. just tested 300 meter.
2. ok, no problem.
3. yes, all app will update relay state.
Thats Great...❤️
but we have one esp32 in this board. how can i able to run KCS firmware and esp32 for home assistant at the same time...?
Looks like a good product. Price seems steep. Did not see amps per channel in the specs.
every relay MAX for AC230v 7A load, INPUT port use dry contact signal
Can you make a video with an example use case like turning on some lights or something so we can also see a wiring example and also how to set up light switches in esphome?
ok, when have free time, can make the new video.
Do you have versions that can handle more than 7A AC?
F16, 16A relay
TOP😍
Hello KinCony., i have a question. If i turn off switch on board, can i control with HA or orther flatform?. I don’t see switch manual in the schematic. Could you help me locate it ? Thank you very much, have a good day
sure, wall switch connect to digital input ports, so that switch button and software can work at the same time
@@KinCony but if i turn on the relay by the switch on the board then the relay state will only be turned off by itself right? and What is the purpose of the switch on the circuit? I would appreciate your reply
@@lqhuy125 Yes, The onboard switch is used in emergency situations and is directly connected in parallel to both ends of the relay coil
I'm sorry, I missed the notification. Thank you very much for the information above.
I like your products, I have Clipsal C-bus system , do you have any products that will interface with the Clipsal C-bus system, or have you thought about doing anything in the near future ? Thanks.
what's "C-bus"? now controller support MQTT, HTTP, modubs multi protocol, if your system support it, it can be integrated.
@@KinCony en.wikipedia.org/wiki/C-Bus_(protocol)
Please tell me How to use Raspberry pi as a Server...plz plz plz .
just install home assistant on raspberry pi
Is it possible to have the switch work even in case you lose ethernet conectivity in 31:00 example? Probably by editing the yaml file?
With ESP Home you can do that yes
sure ,you can edit by ESPHome to set which relay for work, it work locally, without network.
But do you need raspberry pi or
Raspberry pi is already installed
Pi not included, if you want work Pi, need another Pi server. if you want to use tuya app, it can directly to use. But we have another product Pi+relay = one board.
@@KinCony what is that product
Can you install pi on A32
Sir esp32 getting stuck when 3 phase contactor getting off .so can u provide any solution to the problem to avoid device stuck
can you tell me details, or can you take a video of your problem, send to our whatsapp
@@KinCony ok
This device support tasmota or esphome?
support ESPHome for home assistant.
How to have your product in Burkina Faso ?
we only send from China