MX5 MIATA NC / MK3 RAM AIR INDUCTION KIT : install guide
Вставка
- Опубліковано 23 сер 2024
- #mx5 #miata
Give your MX5 Miata NC more growl and better response with the ramair induction kit from Davefab and here is how to install it.
Please consider helping me finish this project by visiting the link below
www.buymeacoff...
thank you
Products in this video:
davefab.com/1-...
Music in this video:
Music track: Cloud by Lukrembo
Source: freetouse.com/...
No Copyright Music for Videos (Free)
ENJOY!!!
Great video, will be using this once my cold air intake gets here
thank you, i hope it helps
Great video!
Thanks!
NICE AND CLEAN, AS USUAL 👍
Thanks again!
Nice video. Just checking - to reset your ecu. You rev between 4&5 k. Do you leave your foot on the accelerator and the revs would drop by themselves?
thank you. yes just leave your foot exactly where it is untill it reaches idle then you can take your foot off
Ta
This is a really good video. Thank you. One question - how it works during a heavy rain? air filter is quite exposed.
thank you. ive not had a single problem and its rained alot here lately
Cracking video mate
thank you 😎
YAY!
😎
Re learning the ECU, how long do you hold the revs for?
Followed this video, was so helpful
until the revs drop by them self, i think it was about 45 seconds
Wow very good job and nice editing video. I plan do the same thing on my NCFL. And what if it will rain? Dont be afraid that air filter soak water? Thank you and have a nice day. Grettings from Czech Republic. :-)
wow czech republic !! thank you very much.
i probably wouldnt drive it through a flood, but there is not a huge worry about the rain
Link to Ramair kit is sick w/ the 404.
thats because the dave fab website is down at the moment. try this one instead
www.mx5parts.co.uk/skuzzle-motorsport-torqintake-induction-mk3-35?gad_source=1&gclid=CjwKCAjwgdayBhBQEiwAXhMxtjrgbQkGJyFUbM0gsd3bv1opCAPbiMUVvk-g-zgwUxwNLfvg1tl_ixoCzdEQAvD_BwE
Hi
It looks like the stock intake to the air box is more or less in the same place as the new one. So effectively, all you are doing is moving the filter from mid flow to the start of the air flow. How or why does this make a difference.
I believe K & N filters provide better air flow than stock. Does the foam filter provide even better flow?
your moving the filter away from the hot air of the engine bay
me personally i would of wanted a k and n filter but it wasn't my car
New subscriber! How often would you need to change the filter, and could you give me an approximate cost for this mod.
no need to change unless damaged but cleaned at least twice a year. i think about £200
Mate you never fail to make me laugh hahahahaha
😂😂
I've got this kit on my NC, noticed the filter can get noticably wet if driving in the rain, which since it's my daily driver too is bound to happen. Have you notice anything similar ?
so far so good with this one. have you got an aftermarket grill ?
@@Project380 Nope still using the stock item, I’ve since realised it’s not leading to any water ingress even if it’s soaked so I’m not hugely fussed. Doesn’t seem to effect the lb/s either
ahh thats good to know@@Quickb3n
super , can I just make it out of black PVC pipe =P
Of course if you wish you can make it out of pvc pipe. But this kit is a specific length to make the best gains. Plus the part that holds the MAF sensor is gonna be tricky to make
Have to pull the bumper to change the air filter?
Yep, or take the under tray off, neither is a fun job, and there's little evidence these thing do anything for an NC, which already has A dedicated cold air feed. All this does is move the filter component to a place where it will get wetter, dirtier and is harder to replace. I wouldn't bother.
just take the under tray off, just a handful of 8mm bolts