This is my Switch and what can i say other then fantastic job! It was a pleasure meeting you and your family when i came to collect, Next time if i ever do anything like this again i promise not to be so heavy handed but if i do then i know exactly where to come. 😅
Thanks to you and this video, I was able to also repair the CLK trace that I accidentally cut. It didn't fixed the switch until I realized I melted the CMD resistor and had to wait 2 weeks for a fresh book of 0208 sized resistor pack to arrive and replace that very tiny resistor.
you are a wizard. i love your videos. thanks a lot for sharing. your new cam is looking awesome. i really enjoy your explanations and talks. ordered everything and will "improve" my switch lite soon.
I've done exactly the same thing on my oled. Apparently Switch have thinner layer of mask than what I used to in X360. Stupid mistake after so many other modded consoles. My repair was quite easy and basically looked just like one here, except for the chip. Few advises for anyone who will try doing it at home: make sure there's no shorts after installing flexes and chip. Just use some kapton tape wherever you soldered wires and on top of the modchip. Chip can also short to the metal shield and you can be surprised when it won't glitch after full assembly the console when it was working while testing. Avoid 2 point DAT0 flexes - you need to make sure it's holding properly as cheap 2 point flexes can lose connection after a while when moving console around (or after a drop). Kamikaze will be most reliable, but definitely not recommended to amateurs. And probably most important advise: don't do it if you don't have any experience with soldering - better find someone who's experienced and recommended. Pay him for installation, not for repair. Great job here, so I would recommend that kind of technician.
18:20 You should start covering the solder point with a small kapton tape. Shield is connected to ground. Had mine come back due to this multiple times.
Yep, i always cut a horizontal 2mm thick thermal pad to size and place it over the dat0 adapter between it and the shield. Helps with heat dissipation, presses down on the adapter and prevents shorts. 😊
i have the same problem. blue light and 3 green lights. do i need to put a file into the chip?? all readings looks good, but i have black screen. It is Pico RP2040 v6.
I missed the 3v connection touchig the cap next to it on the microscope on my oled. And now touchscreen dont work after i figured out the reason for it not booting. Any ideas what i need to replace?
hi i have a question i have switch it works fine in handheld mode but when i put it into the dock it works fine if its stays on mine menu everything is working but when i try to play any game on it while its in the dock it drops the hdmi signal after few seconds
Hi man, I find your videos so awesome. I had a Nintendo Switch V1, while trying to install Picofly mod, I have broke a capacitor on Switch's CPU, is there anyway to recover it? Thank you!
I always enjoy watching your videos. I would like to enter RCM mode only when I press the power button and volume button. Is there a good way? I tried various things myself, but nothing worked. My console is version 2.
Hello, thank you very much for everything you do I have a problem the device boots directly to the base system and does not enter the modified system The shape of the flashes of the LED lamp is as follows : ua-cam.com/users/shortsO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_ Can you help me solve this problem? Thank you very much This is value multimetre Point D : 0.789 A : 0.645 C : 1.468 B : 1.402 3V3: 0.799
This is my Switch and what can i say other then fantastic job! It was a pleasure meeting you and your family when i came to collect, Next time if i ever do anything like this again i promise not to be so heavy handed but if i do then i know exactly where to come. 😅
How do you get in contact with him. I have an OLED failed attempt at modding that needs fixing :((
@@romanrodriguez6883 look in video description
Thanks to you and this video, I was able to also repair the CLK trace that I accidentally cut. It didn't fixed the switch until I realized I melted the CMD resistor and had to wait 2 weeks for a fresh book of 0208 sized resistor pack to arrive and replace that very tiny resistor.
you are a wizard. i love your videos. thanks a lot for sharing. your new cam is looking awesome. i really enjoy your explanations and talks. ordered everything and will "improve" my switch lite soon.
I've done exactly the same thing on my oled. Apparently Switch have thinner layer of mask than what I used to in X360. Stupid mistake after so many other modded consoles. My repair was quite easy and basically looked just like one here, except for the chip.
Few advises for anyone who will try doing it at home: make sure there's no shorts after installing flexes and chip. Just use some kapton tape wherever you soldered wires and on top of the modchip. Chip can also short to the metal shield and you can be surprised when it won't glitch after full assembly the console when it was working while testing.
Avoid 2 point DAT0 flexes - you need to make sure it's holding properly as cheap 2 point flexes can lose connection after a while when moving console around (or after a drop). Kamikaze will be most reliable, but definitely not recommended to amateurs.
And probably most important advise: don't do it if you don't have any experience with soldering - better find someone who's experienced and recommended. Pay him for installation, not for repair.
Great job here, so I would recommend that kind of technician.
18:20
You should start covering the solder point with a small kapton tape. Shield is connected to ground.
Had mine come back due to this multiple times.
Yep, i always cut a horizontal 2mm thick thermal pad to size and place it over the dat0 adapter between it and the shield.
Helps with heat dissipation, presses down on the adapter and prevents shorts. 😊
i have the same problem. blue light and 3 green lights. do i need to put a file into the chip?? all readings looks good, but i have black screen. It is Pico RP2040 v6.
thanks for your job
I missed the 3v connection touchig the cap next to it on the microscope on my oled. And now touchscreen dont work after i figured out the reason for it not booting. Any ideas what i need to replace?
What size of magnet wire are you using?
hi i have a question i have switch it works fine in handheld mode but when i put it into the dock it works fine if its stays on mine menu everything is working but when i try to play any game on it while its in the dock it drops the hdmi signal after few seconds
Why do you solder ground, doesn’t flex on CPU provide?
how much do you take to install on the switch?
Hi man,
I find your videos so awesome. I had a Nintendo Switch V1, while trying to install Picofly mod, I have broke a capacitor on Switch's CPU, is there anyway to recover it?
Thank you!
Hi. Please provide some pictures through WhatsApp +447451466640
I saw that a french guy sucssesfull the rebuild of clk point from the emmc to the cpu
Please provide the link for his video.
@@tvpartsworld806 search FranceRipair clk point
@@tvpartsworld806 wont let me post links. search: "Switch OLED Damaged CLK point - rebuilding CPU trace to eMMC (eMMC reballing) (subtitle ON)"
I always enjoy watching your videos. I would like to enter RCM mode only when I press the power button and volume button. Is there a good way?
I tried various things myself, but nothing worked. My console is version 2.
you have to get a mod chip for a v2
@@trentonmeyers-e5r Thanks brother, I find pressing power-button and volume button, start ofw .
Wow camera is not expensive, but in fact 4K is only 30fps. Anyway, do you know what sensor is inside? 385? Hmm I doubt.
День добрый!!! Подскажите пожалуйста где найти test point точку для вост. на emmc KLMDG4UCTA-B041 153FBGA EMMC 5,1 128GB
Hello, thank you very much for everything you do
I have a problem the device boots directly to the base system and does not enter the modified system
The shape of the flashes of the LED lamp is as follows :
ua-cam.com/users/shortsO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_
Can you help me solve this problem? Thank you very much
This is value multimetre
Point D : 0.789
A : 0.645
C : 1.468
B : 1.402
3V3: 0.799