Відео

It worked, thx

Damaging a capacitor and fixing it right away. I'd leave you with my gadgets and sleep easy!

Good job... Well-done

This helpful buy my problem is my TV is turning on automatically and I can't use the remote to turn it off unless I switched it off from the wall plug and also I can't switch the channel to my decoder

will you install an hwfly on my switch? i always wanted a modded switch but im a kid and i cannot afford a service or learn to solder.

Nice job bro ! +1 sub 👌

Just amazing

Great job !! 👏🏻👍🏻

Hellow! At first, great video😮. I don't understand at all about electronics but I'm trying to learn by myself and the help of a friend and obviously youtube. All of you are great proffessors for me, thank you very much. I have a question, I've found a similar monitor in the street and its works but it seems it has a problem with vertical lines, pixel lines. It has two of them. I tried to find the problem. But no results. Very videos on the internet shows how the cof cables are the guilty of this. I'm figuring to change it or find any shorts on the t-con board. If there are, change the component. What do you think? It's a pity because it looks a very good monitor to save from waste. Thanks again and sorry about my english.😊

What duameter is the enameled copper cable?

Ordering chips it like playing the lottery, you have to be lucky. Great Repair and Video. Thank You.

Bhai mere console me bhi same problem he😢

You are an absolute GENIUS!!!! I took off the yellow strip and unplugged the battery. I waited 30 seconds plugged everything back and i can see my screen now! 🫶🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾

Do I have to erase everything from my SD card before? I have some switch games installed on

i have this error code any idea? 80810001 General power failure (periphery, GDDR6, APU, data line shorted) error code: C00C0002 Description: VRM Controller Failure, Check Mosfet (6414A) Located Side-A, Below Sony Interactive Entertainment Inc. Check Infineon XDPE14286A 16 Phase PWM Controller - Located Side-A, Right of fuse 7001 - Single Beep, 1 second blue light, off.

I'm happy enough to have an Erista switch and not a Mariko model

Anyone name of ic he reballed?

@tvpartsworld hi how do I contact you? Got a referral for something I’d like doing to my device please

modern console suck!

The video is great, I watched it until the end, but my issue is with the Switch Lite. Do you have the same guide for the Lite?

So I tried myself... I tested all the points and flashed with 2.73 firmware --- I get no body and 6 short yellow or green flashes after 1 solid blue. It goes 2 pause 2 pause 2 end - any idea what I can look for or what the code means?

So I attempted to use a picofly on my oled, flashed with current "fw_2.73.uf2" I get one solid blue light, then it flashes yellow twice pause flash yellow twice pause, yellow twice and off and won't boot - What can I check or what did I possibly miss?

Is that a bare copper wire or just bronze color?

Can you come to fix my Xbox

Do you have a diagram of what all the values would be at each solder point? I have this same project to undertake and it would be helpful to know what the readings are at each solder point before I attempt to reinstall the board!

As my xbox is doing the same as the one in the video

Can someone tell me which ram module a xbox needs please

Hello I soldered the first chip by the left on your video and my switch boots up normal without showing no sd card, help pls

Hi friend, same problem on an oled do you have any solutions? I am a technician if you can help me I would be grateful forever! 😊

nice video ... i prefer cables instead this adapter for the points

Another engineer did similar repair but he changed the HDMI ic, now i have ordered the ic to try repairing mine. How do I know the exact part to repair please?

hi when boot to atmosphare i get a fatal error occurred when running fusee.unable to identify package! press power to reboot. in 30.36

I have same orange screen, but i take off my wifi module, and still orange. After this, i put one wifi module from switch lite and still orange screen. What can be?

Why did I hear Dr. D from Phineas and Ferb at the hello part? 😅

Do you have any issues with online playing? lot of colleagues told me that for the offline gaming this is fine but when online you get instabanned. let me know cause you did an amazing job

I think this has to be the VERY FIRST video I've seen which has given the voltages on the different areas of the board., so its A+++ from me.

I have this 2 sec blod after I replaced the psu. It was lightning that broke my first psu. Where can I find ppl in sweden to do this

Where do you get all of the testing point measurements from? I followed along however my RAM is ok (I think, it has higher resistance than your donor board but also not Samsung RAM, so that may be why?)

Holaa a tod@s, Tengo una Nintendo switch que no enciende. La he desmontado , he medido voltajes y batería, carga perfectamente. Al conectarla al PC y con el programa TEGRA_RCM no me detecta nada., para que me salga "RCM device detected" , tengo que desmontar la EMMC, con esto montando no me detecta nada. Aun así, inyecto el payload desde el mismo programa a la SD, pero no hace nada, y sigue sin encenderse....Ayuda por favor!!!

how do you flash the chip?

is it okay if i didnt put uv mask

Good video. Everyone just wants to replace things immediately without doing a little diagnostic work first.

By accident I dropped my switch lite and felf bad , what did he do put it in the grinder😅

Mi consola hace lo mismo, el problema es que no me accede a hekate. Creo que puede ser porque esta parcheada. ¿Hay alguna solución en mi caso?

What happened to your old shop?

En mi opinión: awesome repair!! 😺

Hi mate what size capacitor is it thanks

Great video GREAT REPAIR as usual can I ask where you get your pads from Thanks Millenium Micro Repairs :)

Hi, what is the temp. that you use for soldering?

on 25:00 the big connecting point where the silver is ripped out the trace behind it does that big point goto the little dot to the left