You didn’t have any idle issues with running the stock throttle body? And I’m assuming you just got the block off plate for the idle air control valve ? Bec it’s dif on the skunk 2 manifold then it was my oem.
yeah you can if you want the crank case ventilation to work like stock otherwise you can run that to a catch can and block the port on the manifold so you can keep the inlet clean
Definitely a great upgrade!. Feel more throttle response and more on mid-high gain! Looks great as well. Any suggestion for an intake? Whale penis or cold air intake. Hit Tristan for any question or a hand fitting things out.
hello, i also have an inlet of skunk2 for a d15b7 and bigger throttle body . I was told that he must definitely need and tune after this is correct? Because you just advance the timimg? Thanks
I personally believe that on a dseries engine that is not turbo and only has air intake and exhaust the car will run fine and not need a tune, YES 100% if you tune it you will see an increase in power if you tune it! But other wise they don’t really do anything, on a twin cam Vtec car yes I would agree that you must tune your car after installing an intake like this because they are fine tuned and rev high over 8000rpm the air fuel mixtures change a lot in vtec cars
I have followed this as close as i can with all the same parts and for some reason my civic idles really rough and the rpm maxes out at around 3k rpm and it sounds likes its bouncing off limiter. Any help would be great.
@@TURBOTRISTO i have plugged all unused pipe lines like u in the video and made a plate to cover the d16y8 iacv location like urs. Are there any other places I need to block?
Hey I know it’s years later but check this out, I have a d16y8 and upgraded the intake and throttle body to what appears to be the skunk2 but doesn’t have the symbols anyways same exact set up you got here but when I start the car it goes straight to 6-8k rpm’s right before redline so I shut it off of course I have like no power to my tps wires I multimetered them and only readings I get is on DC volts 200ms and it only shows 5.3-9.1 Molly bolts so basically no power right?
I’ve reran a few wires for the power and ground lines back to ecu new wires just jumping just incase old factory wires got messed up and stuff but still no readings on just regular DC volts 20 that should read at idle 0.50 to open throttle as far as possible 4.45-4.60 volts but I get nothing like I said before I only see millyvolts
If it’s got no volts that’s one thing but it should either stall or idle just on mechanical vacuum if it revs out to 6k there is a major vacuum leak find that first
@@TURBOTRISTO yessir I’ll start spraying so if I were to start it which I need to unless I can take a shopvac and some how tape it to the intake and draw air and spray something around the areas?
hi i saw your video and its cool i have a problem in my car i am from pakistan i have honda civic 1996 model vti pakistan made but the engine is swapped with d15b single v tec manual transmission head code p2j-2 year 97 p2k intake manifold and the ecu is p6f p01 problem is the poor pickup on the lower rpm from 1 to 3k and the fuel mileage is very poor with blacksmoke from exhaust i spend alot of money already but my problem is still there if you have any suggestion or advice then kindly tell me
I have a d16y8 if I buy this manifold along with the throttle body will it run rough/bad without a proper tune ? Or will it run fine without getting it tuned
Have a question for anyone that can help me a little bit more on here..So I have the original 89 Honda civic dx 1.5 L engine would I have to run anything else to connect this intake manifold to the original engine.?
Not really to be honest, you can buy a nitrous kit for half the price of a skunk2 intake that will guarantee you more power , or a turbo kit for about double the skunk2 intake
I bought a throttle body for my d16y7, who sold it sent me one with the different iac valve like a d16y8, and he told me that with the admission of skun 2 I have to adapt the iac, I see that you have no detail in adapting the iac will be that the acceleration body is different since my iac sensor cable has three pins and the one on the body that I buy only has the sensor for two-pin iac
Got a skunk2 im for my y7 wondering how am i able to hook up the iacv on the back of the im. The y7 iacv isn’t compatible on the skunk2 wonder wat iacv should i use
there should be provisions for it on the manifold, I have found with all the skunk manifold's and all the copies they have a spot for all the variations of the d series , you just need to work out which ones you need and which ones to block off, its surprisingly easy
Ey amigo, tengo la mariposa de 70mm pero tengo problemas por qué no es la misma entrada de la válvula iac, mi honda es un d16y7 y la mariposa que tengo es de un d16y8, eñ que me la vendió me dijo que con la admisión de skun 2 tengo adaptarla y veo que tú no adaptas nada con tu mariposa sigue siendo el mismo lugar de la válvula iac, como fue que compraste esa mariposa de 70mm ? Son tener ese detalle
hola amigo mío, lo siento, no tengo un enlace a un cuerpo del acelerador de 70 mm que funcione para usted, esta persona usó el cuerpo del acelerador estándar en su automóvil, y no hubo problemas, solo usamos un bloque de placa para todos los adicionales puertos que no se estaban utilizando
@@TURBOTRISTO i got questions because im confused.. did you still plug your evap solenoid in intake? Cuz i see that you cap it?? Are you running obd1 ecu? Did u just delete it?
im still not sure what you are asking, the skunk 2 manifold has allthe ports you need use your old intake and use all the same parts to conect in the same spot on the new on, any spare holes should be blocked off, i had to make some block offs
Aye @TurboTristan !! I need to know what wheel fitment you used on your silver EK my friend . Been meaning to ask on the new maxpeeding install but keep gettin slammed with work . I have 16s on currently that are in desperate need of powder coat , but my 17s for the accord have been freshly done gloss black . We have the same silver EK , well mines an EJ because well America and stuff but almost same lol .
@@TURBOTRISTO right on , we’ll are they 17s and what tire size did you run ? We can start with that lol . And thanks man I know I aggravate the piss out of ya lol .
@@TURBOTRISTO broooo thank you so much !!! I’ve been painstakingly hunting a 35 series because I was scared with it being so low it would rub but your grey wheels seem to fit perfect on your EK . Jus saved me a lot of time man I really appreciate it 🤘🏻!
ofc i got the throttle body that goes on the manifold which causes me a shit ton of problems. not to mention the coolant lines that go into the bottom of the manifold from the throttle body. i think im just going to go to a shop cause theyll have more of an idea on what to do than i ever will
G'day Brady, the previous owner must have already taken it off before but normally yes you are correct, I will be fitting another one of these to a d series soon I will be sure to show it then
I’m planning on rebuilding a Y8 and I was thinking of getting a skunk 2 intake manifold but would it be worth it if it’s not boosted? Also would I need to get a new fuel rail and bigger injectors?
G'day Captin, you can certainly add the skunk2 manifold it will make the car slower low in the revs, but more powerful hi in the rpm, no you wont need to change the fuel rail or injectors, not unless you are turbo'ng the car
@@TURBOTRISTO ahhh miss heard on the episode, thought you said, when turning steering wheel. If you're sure it's gear box I'd say, box out and start at the Thrust bearing.
@@TURBOTRISTO ok. I have another question. Is it required to adjust timing or can I leave it the way it is after the install? also is turning required?
@@qualitytouch well all the ones for B & D series are quite cheap I am using a hybrid racing shifter in my kswap and I love the feel and quality , but i guess its my fault for buying the ebay $20 and $50 short shift kits for my d series
yeah man I did that in my own EK, just ripped it all out very easy to do very illegal in australia, can make the car a little fumey but I havent noticed it in my car
😅😅 we out here build hondas from junkyards i my self have a a6 head bore and polish 3 angle valves job shave . 40 y8 manifold and others old school style knowledge call streets knowledge and i have a 272 delta cam all motor and d15b2 block light flywheel gd clutch kit and i kp my car around 1600 pounds aluminum parts etc etc and i can tell my crx gd on gas and real real fast she fly from bottom up rpm wise and pull like hell and vtec turbo crap they only see the rear lights waste of time and money for the streets when my hit 2 3 gear and 4 im gone fast and 5 gear she fly straight run and kp pulling i custom made my free flow exhaust system and she sounds tuff real tuff people love her looks and sound and i can say hp don't mean crap if is not used in the right time i build my own with different d engine and b series engine like valves and valves spring and i can say the a6 head love flowing plus i have 72 tb with a custom build adapter and others things and man man what a beautiful feeling to make and have a race car from junkyards parts old school style
@@TURBOTRISTO CCR born in the byouooooo jjjj 😁😎 we do enjoy our toys and we are older guys as well young guys out here enjoying life and our toys old school style nothing fancy primer here and there a bit of light rust and age pain on car nice old school style wheels and low profile tires homemade flares etc we kp old school like our cars but when we hit the gas hold on we flying with 4 bangers hell cats turbos VTEC mustang Camaros etc they nd to really run with us and bingo show time we don't even used air filters only door screen and window screen for filter jjjj 😁😎 like I said junkyard parts homemade and we really run big boys they act bad ass to we start rolling in 2 gear 2500 rpm up show time CCR we smile with all this guys we thousands of dollars cars and engines all noisy but our is flying big difference between blowing smoke and really running jjj 😁 but it is all cool we only having fun and making people mad jjjjj like we said Puerto Rico is in the house let light it up and smokyyy time jjj 😁 is real fun bro to get together and enjoy life peacefully really you know our cars have to run a little rich we love the smell of gas and timing a bit off jjjj normal to burn the fuel with the oxygen nice jjj take care gd video bro regrind Delta cam is the best for guys like us streets poor guys jjj 😁 we made them work gd with timing air mixture and drills jjjj
@@TURBOTRISTO we do out here bro we really enjoy life and our toys around and we like hang out in the parks by the lakes cooking laughing etc older guys young generation girls friends we all cool out here but when we hit the streets we rolling looking for a fight with anything porch corvettes etc only having fun that all people get mad with our Hondas and Toyotas old school style plus a couple Geo tracker with Hondas p28 and y8 manifolds tune up bad ass all motor and couple Suzukis old school costom made adapter for the y8 air intakes and custom made distributor in for the Geo tracker head using y8 distributor they fly like Hondas tune up motor 30 over and head 40 shave port and polish 3 angle valves job with bigger valves old school style nothing fancy people don't believe how fast they are jjjjj 😁 out here the young generation going old school style all motor because they love the sounds and the pull from the cam and combo we really enjoy summer a lot out here peaceful and hanging out we even have 70 years old school guys ripping the streets on carbs doing 9 and 10 on gas in a 1/4 miles and stress rides with 304 cams on 1.8 t Toyotas Corolla motors from the 80s and 4 barrel regular carbs I can tell you we are different breeds out here CCR born in the byouooooo most of us are farm workers construction workers and man man we really love the outdoors old school nothing fancy only regular guys having fun and enjoying life that all and making middle class and rich people mad bitting the crap out their expensive cars jjjjjjj mambo king 👑 light up and show time smoking time jjjj 😁 take care
@@TURBOTRISTO you nd to check out the little jeeps Geo tracker set up with Honda parts air manifold p28 ECM Honda distributor head port and polish and shave bigger cams bad ass set up made in Puerto Rico they recut the Geo tracker distributor and weld the Honda distributor for timing and the p28 ECM for tune bad ass some of them they built them for trails on 4x4 bad ass strong like hell they build a plate for the manifold to hook up to the Geo tracker head 72 tb big difference in the Geo tracker a lot of torque and speed strong gd on gas too easy money gd in highways streets and mountains mud beautiful thing out here
U just got your new subs! Keep up the good content. Regards from 🇲🇾
Maxwell Ogos thank you very much brother ❤️🇦🇺🇦🇺
You didn’t have any idle issues with running the stock throttle body? And I’m assuming you just got the block off plate for the idle air control valve ? Bec it’s dif on the skunk 2 manifold then it was my oem.
yes everything stock will work on the manifold, but be sure to block all the other spare holes so you dont get a vac leak
Your second vacuum line in on the right side of the new mani on the front. Did u run that to the black canister above the water pipe ?
yeah you can if you want the crank case ventilation to work like stock otherwise you can run that to a catch can and block the port on the manifold so you can keep the inlet clean
What did you do to fix the high idle? Also it would have been cool if you show what line you deleted an how you did it.
@@codycastro8083 block all the ports you don’t use
Hey bro, did the silicon around the water inlet hold up good?
Yep
Definitely a great upgrade!. Feel more throttle response and more on mid-high gain! Looks great as well. Any suggestion for an intake? Whale penis or cold air intake. Hit Tristan for any question or a hand fitting things out.
aicel abellera I think a long custom alloy intake would be best tuck the pod behind the bumper in the gaurd
this will be soo helpfull to soo many honda boys and girls
cheers
Hello i have a HRV sohc vtec 2006 model and i wonder if this will show a good upgrade by itself. Will it need another program?
You won’t need a tune
Did you used the OEM throttle body? Was it revving high on idle?
Excellent video! Watching from Puerto Rico! ✔️✔️
No it fired up abs ran fine
hi mate loved the video, was just wondering no need for a tune? i can just slap one on and all good to go?
Yeah man just send it, sure a tune would be ideal , but not necessary
That was very easy a looks really good should be breathing real good great video great content
Thanks Peter
hello, i also have an inlet of skunk2 for a d15b7 and bigger throttle body . I was told that he must definitely need and tune after this is correct? Because you just advance the timimg? Thanks
I personally believe that on a dseries engine that is not turbo and only has air intake and exhaust the car will run fine and not need a tune, YES 100% if you tune it you will see an increase in power if you tune it! But other wise they don’t really do anything, on a twin cam Vtec car yes I would agree that you must tune your car after installing an intake like this because they are fine tuned and rev high over 8000rpm the air fuel mixtures change a lot in vtec cars
I have followed this as close as i can with all the same parts and for some reason my civic idles really rough and the rpm maxes out at around 3k rpm and it sounds likes its bouncing off limiter. Any help would be great.
Just check for vacuum leaks
@@TURBOTRISTO i have plugged all unused pipe lines like u in the video and made a plate to cover the d16y8 iacv location like urs. Are there any other places I need to block?
any spare bolt holes, some of the threaded holes go all the way through
Hey I know it’s years later but check this out, I have a d16y8 and upgraded the intake and throttle body to what appears to be the skunk2 but doesn’t have the symbols anyways same exact set up you got here but when I start the car it goes straight to 6-8k rpm’s right before redline so I shut it off of course I have like no power to my tps wires I multimetered them and only readings I get is on DC volts 200ms and it only shows 5.3-9.1 Molly bolts so basically no power right?
I’ve reran a few wires for the power and ground lines back to ecu new wires just jumping just incase old factory wires got messed up and stuff but still no readings on just regular DC volts 20 that should read at idle 0.50 to open throttle as far as possible 4.45-4.60 volts but I get nothing like I said before I only see millyvolts
If it’s got no volts that’s one thing but it should either stall or idle just on mechanical vacuum if it revs out to 6k there is a major vacuum leak find that first
@@TURBOTRISTO yessir I’ll start spraying so if I were to start it which I need to unless I can take a shopvac and some how tape it to the intake and draw air and spray something around the areas?
I have a d16y7 engine and my buddy gave me his y8 intake manifold, will it fit okay?
Yeah sure will
hi i saw your video and its cool
i have a problem in my car
i am from pakistan
i have honda civic 1996 model vti pakistan made
but the engine is swapped with d15b single v tec manual transmission head code p2j-2 year 97
p2k intake manifold
and the ecu is p6f p01
problem is the poor pickup on the lower rpm from 1 to 3k
and the fuel mileage is very poor with blacksmoke from exhaust
i spend alot of money already but my problem is still there
if you have any suggestion or advice then kindly tell me
Wow man sorry that’s too tricky to figure out over the internet best go see a mechanic to diagnose
Is no video up on the Skunk2 idle air control valve setup can you do one please
Check out the video I did where I did every bolt on in an N/A d16
By chance where did you get the block off plate on the back of the throttle body from
Made them
I have a d16y8 if I buy this manifold along with the throttle body will it run rough/bad without a proper tune ? Or will it run fine without getting it tuned
It will be fine just make sure you blank off all the unused ports
I have a 02 honda civic lx sedan 1.7 I think it's SOHC D17. What skunk2 manifold can I use.? And will it pads smog
It won’t effect your smog results , I beleive the same one from an ek will fit d16y4/7/8 manifold
Best to ask skunk themselves
Thank you.
I have this same car I can't wait to get a skunk 2 I'll post up my videos
Awesome bro in the mean time subscribe to my channel
Just one question where did you get a iac valve delete plate at ??
I made it
Alright thanks
@@TURBOTRISTO Mind sharing measurements/blueprint?
Have a question for anyone that can help me a little bit more on here..So I have the original 89 Honda civic dx 1.5 L engine would I have to run anything else to connect this intake manifold to the original engine.?
You would need a d16 efi head and a full efi set up,
I just installed one on my Y8 but having a hard time re connecting hoses and plugging stuff back in, not sure where they go
Look at pics of how it was or follow this tutorial man everything is the same just slightly stretched out
Need some help plugging in everything for my mini me swap using skunk 2 manifold
Every thing should just match up plug to plug. What’s the issue man
@@TURBOTRISTO just curious on what I have to plug in and what I have to block off. Doing a mini me swap d16y7 y8 head.
Did you feel any difference in power with the new intake manifold? Do you think is worth it this modification?
Not really to be honest, you can buy a nitrous kit for half the price of a skunk2 intake that will guarantee you more power , or a turbo kit for about double the skunk2 intake
I bought a throttle body for my d16y7, who sold it sent me one with the different iac valve like a d16y8, and he told me that with the admission of skun 2 I have to adapt the iac, I see that you have no detail in adapting the iac will be that the acceleration body is different since my iac sensor cable has three pins and the one on the body that I buy only has the sensor for two-pin iac
I just used the stock throttle body and stock iacv and everything is perfect
Thank for awesome video…!
thanks Don!
great video man!!
Thanks for the visit
I have a idle too high and surging on my d16 skunk2 pro series. No vacuum leaks. Any tips on where to check?
You will 100% have a vacuum leak, check for any Screw or bolt holes
@@TURBOTRISTO i put my palm to block of the throttle body and the car dies so means no vacuum leaks
Got a skunk2 im for my y7 wondering how am i able to hook up the iacv on the back of the im. The y7 iacv isn’t compatible on the skunk2 wonder wat iacv should i use
The iacv is on the throttle body on a y8 so maybe use that’s and blank off everything else
@@TURBOTRISTO the iacv for the y7 is a 3 plug and the y8 is a two plug
@@matthewtawagon7908 and where is it mounted?
there should be provisions for it on the manifold, I have found with all the skunk manifold's and all the copies they have a spot for all the variations of the d series , you just need to work out which ones you need and which ones to block off, its surprisingly easy
Ey amigo, tengo la mariposa de 70mm pero tengo problemas por qué no es la misma entrada de la válvula iac, mi honda es un d16y7 y la mariposa que tengo es de un d16y8, eñ que me la vendió me dijo que con la admisión de skun 2 tengo adaptarla y veo que tú no adaptas nada con tu mariposa sigue siendo el mismo lugar de la válvula iac, como fue que compraste esa mariposa de 70mm ? Son tener ese detalle
hola amigo mío, lo siento, no tengo un enlace a un cuerpo del acelerador de 70 mm que funcione para usted, esta persona usó el cuerpo del acelerador estándar en su automóvil, y no hubo problemas, solo usamos un bloque de placa para todos los adicionales puertos que no se estaban utilizando
@@TURBOTRISTO gracias saludos
What was the block off plate for? It was on the back of the intake near the firewall. where can I get one?
some of the vtec models have the IAC valves on the back the d16y4 doesn't its part of the throttlebody
My question did u have to tune it after install or was it running of stock ecu ???
Nah stock is fine
200 more subscribers to go dude !
Hell yeah I’m counting down til I can get to 1000!!! Thanks for your support and thanks for the comments it helps the algorithm alot
Whag did you do to the canester hose.
What canister hose my man
@@TURBOTRISTO the one on top of the throttle body.
Where did you put the coolant hose from pipe? Is that the gray hose u got?
I don’t have any grey hoses, could you timestamp the part you are referring to
@@TURBOTRISTO i got questions because im confused.. did you still plug your evap solenoid in intake? Cuz i see that you cap it?? Are you running obd1 ecu? Did u just delete it?
Because aftermarket tuck harness doesnt have evap purge solenoid. Just thinking if i can delete it since im moving p28 obd1
im still not sure what you are asking, the skunk 2 manifold has allthe ports you need use your old intake and use all the same parts to conect in the same spot on the new on, any spare holes should be blocked off, i had to make some block offs
easy to follow instructions 👍
Asia Issabella thank you 😁
Aye @TurboTristan !! I need to know what wheel fitment you used on your silver EK my friend . Been meaning to ask on the new maxpeeding install but keep gettin slammed with work . I have 16s on currently that are in desperate need of powder coat , but my 17s for the accord have been freshly done gloss black . We have the same silver EK , well mines an EJ because well America and stuff but almost same lol .
I am not sure of the specs I’ll try look in a few days I have to take the rims off to fit the new ek4 sway bars
@@TURBOTRISTO right on , we’ll are they 17s and what tire size did you run ? We can start with that lol . And thanks man I know I aggravate the piss out of ya lol .
@@lostkauz83 no man not at all they are 205/40r17 I’m sure they are 7.5 wide
@@TURBOTRISTO broooo thank you so much !!! I’ve been painstakingly hunting a 35 series because I was scared with it being so low it would rub but your grey wheels seem to fit perfect on your EK . Jus saved me a lot of time man I really appreciate it 🤘🏻!
@@lostkauz83 yeah boiiii 40s are a common size so they will be cheaper too
ofc i got the throttle body that goes on the manifold which causes me a shit ton of problems. not to mention the coolant lines that go into the bottom of the manifold from the throttle body. i think im just going to go to a shop cause theyll have more of an idea on what to do than i ever will
Give it a go man it’s satisfying
Wasn't there a bracket under car u needed to remove?
G'day Brady, the previous owner must have already taken it off before but normally yes you are correct, I will be fitting another one of these to a d series soon I will be sure to show it then
Here in the US there called Junk2 products. We don't really use them anymore. At least the OG wise builders dont
True bro the skank manifolds are junk
What manifolds do people like to run on their d series now?
another good vid bro
allegiance crew thanks heaps man
Why it have avance in the distribution?
Usually gives a slight power increase
Worked out well
Yeah it sure did
I’m planning on rebuilding a Y8 and I was thinking of getting a skunk 2 intake manifold but would it be worth it if it’s not boosted? Also would I need to get a new fuel rail and bigger injectors?
G'day Captin, you can certainly add the skunk2 manifold it will make the car slower low in the revs, but more powerful hi in the rpm, no you wont need to change the fuel rail or injectors, not unless you are turbo'ng the car
GoPro 360 on the roof will be sick!!
Stuart Howitt I’m looking forward to getting one
What did you think of the catch phrases? And the patreon stuff?
Yeah all good!
The VisIoN!
all the vision
Questions sir is it fine to run a d15b7 manifold on a d16y7 engine???
Sure is if it fits
@@TURBOTRISTO yes fits and runs but just wanted to make sure since there from different engines before getting a throttle body for the manifold
Where does the fuel regulator connect to ?
The fuel rail
Hi, just bought the skunk2 intake and would like to know what size of screw you use to plug the hole on the side.
Hello what hole do you mean?
There’s three hole in the other side of the intake. One hole goes through inside and the other two has thread.
Its all threaded by the way. Its just the big hole goes through inside the intake.
@@marinelocarandang891 oh yeah that is for some kind of additional sensors
Do you remember which size of screw you use to plug in. Did you put any sealant in screw.
Stickers would be good
They will be coming soon
Check the Power Steer Pump first if there's a noise turning the steering wheel
Stuart Howitt hard to hear on the video but it’s 100% from the drivetrain/gearbox or clutch
It sounds horrendous like a grinding and whining and crunching all at the same time
Only when turning the steering wheel? 🤔🤔🤔🤔
Stuart Howitt no it doesn’t make any noise when you move the steering wheel
@@TURBOTRISTO ahhh miss heard on the episode, thought you said, when turning steering wheel.
If you're sure it's gear box I'd say, box out and start at the Thrust bearing.
Can I put this manifold on a D16Y7 non VTEC ?
I’m asking because my throttle body sits straight up with the air filter on top
You sure can man
what size was the throttle body? cheers
This was with the stock throttle body
Nice video
Minecraft080808 thanks bro
When’s the kswap AWD ?!
I will be doing a kseries awd as soon as my fabrication skills are on point so I can do the work myself
I wish you would have done a step by step on the lines you deleted.
@@codycastro8083 it’s very straight forward
@@TURBOTRISTO ok. I have another question. Is it required to adjust timing or can I leave it the way it is after the install? also is turning required?
Leave it the way it is but always recomend a tune for any mod
Yooooo, gonna do this to mine i hope
great way to spend a saturday afternoon
@@TURBOTRISTO my short shifter came in...so stoked
@@qualitytouch i have done videos on cheap short shifters i have taken them out i dont rate them as a mod
@@TURBOTRISTO y cheap??
@@qualitytouch well all the ones for B & D series are quite cheap I am using a hybrid racing shifter in my kswap and I love the feel and quality , but i guess its my fault for buying the ebay $20 and $50 short shift kits for my d series
Wanna see more on deleting things or bypassing things on D16y8s
Louis Sabatini do I want to? Or do you want to? 😀
In that case you will be happy my next video I plan to delete a few more things,
Hi have you done a egr delete and carbon canister delete any info would be great on a ek3
yeah man I did that in my own EK, just ripped it all out very easy to do very illegal in australia, can make the car a little fumey but I havent noticed it in my car
Also how install intakes like those on automatic versions
Louis Sabatini automatic will be exactly the same 😄
😅😅 we out here build hondas from junkyards i my self have a a6 head bore and polish 3 angle valves job shave . 40 y8 manifold and others old school style knowledge call streets knowledge and i have a 272 delta cam all motor and d15b2 block light flywheel gd clutch kit and i kp my car around 1600 pounds aluminum parts etc etc and i can tell my crx gd on gas and real real fast she fly from bottom up rpm wise and pull like hell and vtec turbo crap they only see the rear lights waste of time and money for the streets when my hit 2 3 gear and 4 im gone fast and 5 gear she fly straight run and kp pulling i custom made my free flow exhaust system and she sounds tuff real tuff people love her looks and sound and i can say hp don't mean crap if is not used in the right time i build my own with different d engine and b series engine like valves and valves spring and i can say the a6 head love flowing plus i have 72 tb with a custom build adapter and others things and man man what a beautiful feeling to make and have a race car from junkyards parts old school style
Cool as man
@@TURBOTRISTO CCR born in the byouooooo jjjj 😁😎 we do enjoy our toys and we are older guys as well young guys out here enjoying life and our toys old school style nothing fancy primer here and there a bit of light rust and age pain on car nice old school style wheels and low profile tires homemade flares etc we kp old school like our cars but when we hit the gas hold on we flying with 4 bangers hell cats turbos VTEC mustang Camaros etc they nd to really run with us and bingo show time we don't even used air filters only door screen and window screen for filter jjjj 😁😎 like I said junkyard parts homemade and we really run big boys they act bad ass to we start rolling in 2 gear 2500 rpm up show time CCR we smile with all this guys we thousands of dollars cars and engines all noisy but our is flying big difference between blowing smoke and really running jjj 😁 but it is all cool we only having fun and making people mad jjjjj like we said Puerto Rico is in the house let light it up and smokyyy time jjj 😁 is real fun bro to get together and enjoy life peacefully really you know our cars have to run a little rich we love the smell of gas and timing a bit off jjjj normal to burn the fuel with the oxygen nice jjj take care gd video bro regrind Delta cam is the best for guys like us streets poor guys jjj 😁 we made them work gd with timing air mixture and drills jjjj
sounds like you are living the dream
@@TURBOTRISTO we do out here bro we really enjoy life and our toys around and we like hang out in the parks by the lakes cooking laughing etc older guys young generation girls friends we all cool out here but when we hit the streets we rolling looking for a fight with anything porch corvettes etc only having fun that all people get mad with our Hondas and Toyotas old school style plus a couple Geo tracker with Hondas p28 and y8 manifolds tune up bad ass all motor and couple Suzukis old school costom made adapter for the y8 air intakes and custom made distributor in for the Geo tracker head using y8 distributor they fly like Hondas tune up motor 30 over and head 40 shave port and polish 3 angle valves job with bigger valves old school style nothing fancy people don't believe how fast they are jjjjj 😁 out here the young generation going old school style all motor because they love the sounds and the pull from the cam and combo we really enjoy summer a lot out here peaceful and hanging out we even have 70 years old school guys ripping the streets on carbs doing 9 and 10 on gas in a 1/4 miles and stress rides with 304 cams on 1.8 t Toyotas Corolla motors from the 80s and 4 barrel regular carbs I can tell you we are different breeds out here CCR born in the byouooooo most of us are farm workers construction workers and man man we really love the outdoors old school nothing fancy only regular guys having fun and enjoying life that all and making middle class and rich people mad bitting the crap out their expensive cars jjjjjjj mambo king 👑 light up and show time smoking time jjjj 😁 take care
@@TURBOTRISTO you nd to check out the little jeeps Geo tracker set up with Honda parts air manifold p28 ECM Honda distributor head port and polish and shave bigger cams bad ass set up made in Puerto Rico they recut the Geo tracker distributor and weld the Honda distributor for timing and the p28 ECM for tune bad ass some of them they built them for trails on 4x4 bad ass strong like hell they build a plate for the manifold to hook up to the Geo tracker head 72 tb big difference in the Geo tracker a lot of torque and speed strong gd on gas too easy money gd in highways streets and mountains mud beautiful thing out here
So young dude
Haha what do you mean
@@TURBOTRISTO time flies
@@nathanlevander1867 oh yeah for sure it does