how to plug in 140hz actuator (6NW009420) in edc15p+? is it possible to use vcds to set the chanel? and how to do it please, i'm trying to ask tuners forum with no replying. it will preferable to not use damos. thank you
Ahoj, hodnota 833 = 300Hz. Pokud chci 140Hz tak hodnotu musím změnit na 388,734. Pokud to píšu špatně tak prosím o radu. Jde hodnota změnit ve VCDS nebo to musím udělat ve Winols ? ( mám obojí )
833 je hodnota pre preddeličku, alebo niečo také (ospravedlňujem sa ale som strojár a nemám naštudované programátorské výrazy). Keď chceš znížiť frekvenciu tak tak musíš dlhšie plniť preddeličku. Určite potrebuješ hex editor
@@milanvojciniak7890 Už se to podařilo spočítal jsem to špatně protože hodnota 833 = 3,33ms = 303Hz 1800 = 7,20ms = 138Hz 1999 = 8,00ms = 125Hz Bmw rea funguje na 300Hz Mercedes rea funguje na 140 Hz
@@Lucian18905 You are probably righ. If you are looking for edc16 solution, try to to ask on tuners forums. Buy oscilloscope, measure edc16 N75 frequency and try to look for the frequency in millis or micros.
how to plug in 140hz actuator (6NW009420) in edc15p+? is it possible to use vcds to set the chanel? and how to do it please, i'm trying to ask tuners forum with no replying.
it will preferable to not use damos. thank you
pin1 +12V, pin2 GND, pin4 negative pole of PWM signal. it is not possible vith VCDS
@@milanvojciniak7890 thanks but how to switch n75 signal as 140hz pls?
@@sergio84593 it is mentioned in some comments under this video I think
Ahoj, hodnota 833 = 300Hz. Pokud chci 140Hz tak hodnotu musím změnit na 388,734. Pokud to píšu špatně tak prosím o radu. Jde hodnota změnit ve VCDS nebo to musím udělat ve Winols ? ( mám obojí )
833 je hodnota pre preddeličku, alebo niečo také (ospravedlňujem sa ale som strojár a nemám naštudované programátorské výrazy). Keď chceš znížiť frekvenciu tak tak musíš dlhšie plniť preddeličku. Určite potrebuješ hex editor
@@milanvojciniak7890 Už se to podařilo spočítal jsem to špatně protože hodnota 833 = 3,33ms = 303Hz
1800 = 7,20ms = 138Hz
1999 = 8,00ms = 125Hz
Bmw rea funguje na 300Hz
Mercedes rea funguje na 140 Hz
how do i change it do I look for the value 883 and how do I change it?
833
@@kamilvihonsky5812 833 is for 300Hz. It's SVBL. It is simle math. Circa 1700 is 140Hz or so...
@@milanvojciniak7890 the value 833 is not the only one in edc15vm there are at least two and edc 15p there are more
@@kamilvihonsky5812 use damos and find correct one. Or try to change one, and than second one.
How much do You want to share the adress of the PWM freqvency
I do not need you money. It is single value 833 in EDC15VM/P
@@milanvojciniak7890 ok thanks..
For edc 15 its easy,there are actuators that work plug and play.
Edc16 is different story
@@Lucian18905 You are probably righ. If you are looking for edc16 solution, try to to ask on tuners forums. Buy oscilloscope, measure edc16 N75 frequency and try to look for the frequency in millis or micros.