Always found it much easier to go from the top down into the tank & pull thru with a pair of long pliars! No need for the xtra wire. Always worked well for me!
On the primer bulb , the IN side goes to the small brass tube on carburetor and the OUT side of primer bulb goes to tank return by the right side of carburetor as viewed from the top of saw ! The idea is the primer bulb when pushed in squirts gas into tank and when released pulls gas through the fuel filter via drawing it through the carb through the small brass tube on carburetor
I hope you don’t have to work on that Troybilt 4 cycle trimmer on the table. How do I know this? Because I replaced the starter pawls on mine twice because it never started right from new, Then when it started bogging I threw it across the yard, I bought an Echo trimmer 3 years ago and never have had any problems.
wanna come over and fix mine? hahaha i cleaned the filter on carb-blew it off, looked at spark plug but couldn't get it out. bulb pushing fuel. IDK. has ruined my fire to go cut wood.
I just got one of these for free as well. A Poulan 220 Pro 38cc. Completely trashed, rusted bar and chain, no fuel lines or primer bubble. Looks like it was sitting under 3" of mud for a while.
I've tried for years to develop any affection at all for poulan saws, just because everyone dogs them. I just can't do it. They all suck. Poulan made me ditch anything from husqvarna and start buying stihl and echo products.
Great stuff! Was curious if that fuel line would feed better if left in the freezer for 20 minutes or so?
Always found it much easier to go from the top down into the tank & pull thru with a pair of long pliars! No need for the xtra wire. Always worked well for me!
Great video and instruction! Thank you!
👍👍
good clear from the first to the end good about a little wire tool to feed the fuel line from fuel tank to the carburetor thank you !!!!
Glad it helped👍👍
Thanks for another great video 📹!!
Keep on 'Pullan' '
On the primer bulb , the IN side goes to the small brass tube on carburetor and the OUT side of primer bulb goes to tank return by the right side of carburetor as viewed from the top of saw ! The idea is the primer bulb when pushed in squirts gas into tank and when released pulls gas through the fuel filter via drawing it through the carb through the small brass tube on carburetor
Dang, sounds like a jungle out there.
Cut a small taper on the end of the new fuel lines & they will go right into the tank!
Great video
Thats a Nice trick. But how did You tie the wire?
I think it's going to be just like that one but I know how too adjust it now thanks a lot very much
Glad I could help
fuel lines are the weak spot on them ..i have that saw,,an many other poulans very easy to work on,,,
Every year
Do you have rattle snakes sounds like it,?
I hope you don’t have to work on that Troybilt 4 cycle trimmer on the table. How do I know this? Because I replaced the starter pawls on mine twice because it never started right from new, Then when it started bogging I threw it across the yard, I bought an Echo trimmer 3 years ago and never have had any problems.
Y
Well yeah Troy Bilt is junk.
The chain should not be moving at idle if the chain brake is off and the throttle isn't depressed. You may have a bad clutch brake too!
Fuel line
small fuel line is supposed to go to fuel filter
I think it's the Leatherface chainsaw replica.
good job
Best to order a air boot to
There short life
Very popular in west Texas
Fuel lines filter and metering diaphragm and fixed
How to Install fuel line
Where can I order that same gas line? good vid man!
I believe I got it on Amazon.
@@SmallEngineDIY thanks man
Is the sprinkler on or a heard of snakes? 😁 (👍)
LOL 👍👍
wanna come over and fix mine? hahaha i cleaned the filter on carb-blew it off, looked at spark plug but couldn't get it out. bulb pushing fuel. IDK. has ruined my fire to go cut wood.
It can be frustrating, but don't give up!
it needs to lay on the bottom
I expected an ostrich to stick its head into camera view...you must live on a wildlife preserve....not that that is a bad thing...
I just got one of these for free. I figure the initial investment being free it might me worth playing with to get running
Good luck with it!
@@SmallEngineDIY Got it running! Thanks for your help. You gave me the confidence to giv’er!
I just got one of these for free as well. A Poulan 220 Pro 38cc. Completely trashed, rusted bar and chain, no fuel lines or primer bubble. Looks like it was sitting under 3" of mud for a while.
I've tried for years to develop any affection at all for poulan saws, just because everyone dogs them. I just can't do it. They all suck. Poulan made me ditch anything from husqvarna and start buying stihl and echo products.
I cant get past the background noise, sounds like a rattle snake nearby. Get that chainsaw fixed quick or else!❤
Its poulan not poolan 😅
Pisto ring