The Easiest Way to Remove Paint to Bare Metal!
Вставка
- Опубліковано 29 бер 2024
- In this video we will visit into one of the most effective paint strippers on the market today! In some cases, we will need to remove the paint from our panel to get it back to bare metal. In the past this has always been a painful task until now!
🟢CHECK OUT OUR ONLINE STORE🟢
www.amazon.com/shop/paintsociety
🔺Get the OFFICIAL Paint Society Paint Suite Here🔺
amzn.to/3Eq3pSf
🔺Get the OFFICIAL Paint Society Pump Sprayer Here🔺
amzn.to/49kZbsY
To Receive 10% off #Eastwoodco Products use coupon code BRIAN10 at eastwood.com
Products in this Video
Eastwood Epoxy: amzn.to/43GSsYD
Aircraft Paint Remover Sold at Most Automotive Stores, not yet on Amazon
Tear Off Micro Fiber: amzn.to/48FAI0z
K600 Handpad: amzn.to/4aD8LIb
Proper Respirator to Use: amzn.to/3PLJMdI
Paint Scrapper: amzn.to/3IVAubf
Sagola DVR Digital: amzn.to/3ZcPybx
Sagola Aqua Cap for Solvent and Water Basecoats: amzn.to/3r8tDFX
3M Performance Spray Gun: amzn.to/3BXUwPu
Naked Gun Cleaner: amzn.to/3SmFI4b
PPS 14 Oz Cups: amzn.to/4247uGJ
PPS 28 OZ Cups: amzn.to/3NV5I58
Plastic Masking for Vehicle: amzn.to/3HH7S4Z
3M Yellow Automotive Tape: amzn.to/3vBtbCa
Other products used in other videos:
CLEANERS
Degreaser: amzn.to/3Pvghgu
Prep Cleaner: amzn.to/39EvWrd
Tack Rag: amzn.to/3sMvyk5
Spray Way Glass Cleaner: amzn.to/49GUPxd
Microfiber Tear Away Towels: amzn.to/3sGjVuO
MASKING
36'' Masking Paper: amzn.to/3RiPFAv
18'' Masking Paper: amzn.to/3r6hoK8
6'' Masking Paper: amzn.to/3RbmEH3
1/2 Fine Line (Used in the video): amzn.to/3P7ULNr
3M Masking Tape: amzn.to/3raZF4b
Foam Tape: amzn.to/461jKZx
1/4 Fine Line: amzn.to/3ER7U8Z
Masking Machine: amzn.to/45IieeV
other products
Astro Sunlight: amzn.to/3NrI3HZ
Paint Gun Cleaning Kit: amzn.to/3qZ4dXM
Gloves: amzn.to/3R9C9eW
Gun Cleaner: amzn.to/3LDv2tW
Water Cleaner: amzn.to/3Budv2V
Prepping Sandpaper Starter Kit: amzn.to/3UplwPS
Prep Cleaner: amzn.to/3fZ2KPn
Tolecut Sanding Dirt Nibs: amzn.to/3PFDcEm
Griots Garage Polisher: amzn.to/3jeim2p
Milwaukee Mini Buffer: amzn.to/3G28ORm - Авто та транспорт
Buy the Official Paint Society Spray Suite Here! amzn.to/3IXYkD1
Are there cheap alternatives?
Can brake fluid be viable?
I purchased a pickup that previous owner had spray painted over the factory paint (no prep). How can I remove only the paint they added???
The factory paint is good.
Great video. I would like to give you a word of caution when using a paint stripper like this. I am a retired Air Force aircraft painter with 40 years experience. I'm sure this product is not as strong as the stuff we use, but the fumes can be very dangerous. Please do not use the type of mask filters the guy is wearing in the video. Those are made for heavy particulates and or dust, not vapors and fumes. Those type off ilters will do nothing to stop the vapors from that paint stripper. If anything they will concentrate the fumes more inside the mask. When using this stuff, be sure to use an organic vapor and mist rated filter on your respirator. Check the instructions on the different types, but I believe the ones needed are the pink and black style or the pink and yellow 3M style cartridges for that type of mask. The proper cartridges have a charcoal layer inside the cartridge and a prefilter that helps stop the fumes and vapors. A full face would be better for eye protection. Be safe out there everyone.
My toxic trait is watching videos like this and thinking "He makes it look and sound so easy, I should try it!" without thinking about the 20 years of experience that went into making it look easy.. Who's with me? 🤣
Do it!!! And i only have 7 years professionally experienced haha
@@PaintSociety 7 or 20, you still make it look very easy! It is a skill I'd love to pick up though :)
same here bro,
it all looked too easy 😅
You sound like a soccer mom. "My toxic trait is" 😂
@@PaintSociety
Have you tried this product on powder coating?
I work in a shop, we recently stripped a set of wheels with this same product. To say it works great, even on powder coating it takes a bit longer. Just don't let it dry out, the slag paint becomes harder than it was. Great stripper. Wear eye protection,gloves, and probably outside.
thank's for the tip 👌
Did you use 2k epoxy on the alloy wheels after stripping ? Or something else?
@@harshadchari6065 We coated the wheels with self etching primer, then urethane primer. Before urethane base and clear coat. Hopefully it holds up for many years. IDK it was the shop owners call on the material used.
A couple of decades ago I had to strip a hood which was painted multiple times by a so called professional. It has so many layers of paint it actually looked like a cheap fiberglass hood.
I used the same process shown using plastic sheeting to capture the active ingredients while is worked.
The hood was stripped clean and primed, painted, cleared.
The shop manager was happy and more importantly, the customer was happy.
All killer, no filler. Very impressive because I know that it is a lot of work to make it look easy.
Just what I needed to see to inspire me to finally strip and paint the hood of my Tahoe. Except its not a project, it's my daily. 😅 and I have always appreciated how the steps and explanations are geared towards those who are predominately do-it-yourselfers.
I love this channel, I always learn something. Brian is a great teacher, he's clear, doesn't repeat himself over and over, he gets right to the point no endless backstories, and no uhs or ums. Really wish I saw this before I painted my truck black. I'd love to see a video on buffing too.
Lovely. Prepping for a project and trying to learn ahead of the work. This was certainly above my pay grade but beautiful results. Most chemical paint removers I've seen or used can't fight their way out of a paper bag because of healthandsafety but great tip to cover. As ever, loads of great help here. Many thanks!
Bro you make magnificent videos. You are a teacher at heart. Thank you for your vids.
Thanks Brian! Have you ever tried Coopers Strip Club products made in New Zealand? I’m restoring a Jaguar E-type coupe, I used their system and it was terrific - I stripped the entire car to bare metal. You spray it on with just a pump sprayer, let it sit for a bit then take the paint off with steel wool and a metal blade. Nearly no oder, a lot less messy and easy clean up!
I agree …. Check out diy auto school my friend Pete !!!he highlighted the product and he is real world and knows his stuff
I have to strip the paint in my 91 Firebird hood. This is exactly the video I needed!! Thank you.
Thank you so much for this Brian. Your videos and tips/tricks of the trade are nuggets of gold. Cheers
Awesome Tutorial! Thanks for sharing!
Thanks Paint Society, this was a very good description of the process and steps to take for a great paint job.
That finish turned out great
Great video, I too use that paint stripper but when I covered with plastic, it didn't pill as easy as it did for you, I had better results without. And I have better results in my paint jobs when I do a 50-50 or 75 overlap. Thanks for what you do.
Keep up the great work. I ALWAYS love watching your content. You keep it real and basic so that guys like me can learn easily. Cheers
I appreciate that!
Eastwood contour sct tool will definitely get the job done
That looks fantastic ! Thank you. It's great to watch a Profesional.
Thank's , I'm going to do this to my OBS 95 F 150. The hood has small crack's in the paint that I think go all the way down to the base metal. I was dreading having to sand it all the way down. Love your channel I've learned so much from you. Rob......
It's looks wonderful
Lots of good information, thanks for sharing
Klean Strip used to have a dry process paint stripper back in the day. It would go on wet, wrinkle and dry. You could then run a razor blade over it down to bare metal. Stripped my 65 Pontiac with one gallon!
Great results! Will this stripper work to remove factory rocker guard and seam sealer and surface pitting rust?
Thanks Brian, as per usual another very informative video 👍
Love the video, thank you for all the knowledge shared.. Hey Brian what's the best way to strip a plastic bumper cover?
Fantastic work, Hope mine comes out perfect
I used the aircraft paint remover in a spray can. That thing worked amazing on my valve cover for my Honda Civic
Great instructional video, well done. I'm surprised that stripper did so well, normally that new stuff does nothing even though I do the cling wrap step as well.
Super Duper excited 😮 Awesome 👍🏼 thankyou for sharing. Can't wait to start on my ride on tractor cover's 👍🏼
The system I use has a 2k etch primer you can put in the gun. I strip the paint to bare metal, sand up to 320 on a da, etch (2 coats), seal, base, clear. Works great.
Excellent commentary 👍
Another good lesson
Lots of Great tips on this one Brian! Im going to try and start at least finishing off with a D.A. and soft pad before polishing. Thanks Brother!
You can do it!
Now THAT is a great DIY suggestion!!! 😁
I used some acetone to clean off before paint and i should have used respirator caused me to get high and in a hurrey .i painted it with mastercoat primer slim .it didint stick to good but is was plated so im gonna try etching primer
I find red scotch brite pads are pretty good for the scuffing part, less chance of rub through if you have a lot of curves.
Absolutely love these videos love the watch and make more Sean formative…👍👍
Brian, I truly enjoy your channel and have learned a ton from you. I am a DIYer and into old 50-60’s cars. I am just starting a project of stripping the metal for rust repairs and body work. I would appreciate if you could give me your opinion on using “Klean Strip- Concrete & Metal Prep” on the bare metal after I get it stripped before It gets the epoxy primer? Are there any watch outs or other prep process that would be required if using that Metal Prep? Thanks!
Great video Brian! That stuff work as well as it used to, especially on catalyzed or baked enamels. I think that they may have removed some of the caustic chemicals for environmental reasons.
love your videos Thanks Brian
Nice job.
Hi Brian thanks for the video! This actually motivated me to re-try painting my hood that I messed up the first time! Do you have any recommendations on a inexpensive gun that can deliver similar results to yours in this video? Also I think about enclosing a part of my workshop with plastic and plywood wood to make a "dust free" room and using to square fans with house filters one pulling and one pushing. Do you think this is a good idea for a diy spray boot? Any advice are welcome and thanks again for this amazing video! From 🇨🇦
awesome demo.
Glad you liked it!
Thanks Brian have been useing aircraft stripper for a long time. The new formula low voc sucks compared to the go formula But I like the cover it with plastic going to have to try it on a firewall might be a little harder since its vertical 👍👍
Hi, great videos, have subscribed for a while and learnt alot. I was wondering if you could do a video on rust proof painting new car parts, found lots of info on treating rusted parts but not much out there on rust proofing new parts like subframe. Many thanks
The old yellow aircraft paint stripper was the best
I’m not a painter nor a spray painter but I pickup a lot of different skills by watching UA-cam videos and I’m pretty good at it I did some bodywork on my 2006 Dodge Dakota truck V8 SLT and it came out pretty good for a beginner watching your videos I think I’ma paint it my self I mean what’s the worst that could happen right practice makes improvement
Great video brother
Great video! 👏👏👏
Awesome video. How did you neutralize the paint remover?
looks like a great product to remove the paint on my boat. 👍
Looks really nice. How would it look color sanded with the Linear Blocking System??? I'm a professional detailer and I'm looking to pull the trigger on that. Also, how long before the paint gasses off before color sanding? Thanks for a great presentation!
Thanks for this video. A question I have is how would you protect a shelled car as I do work in sections.
I was wondering what brand of paint can mixer and pourer you use for your one gallon paint cans.
Thanks
I'm new to all this but man you guys do an awesome job on UA-cam University gonna be re doing my 2012 suburban roof I have learned a lots from you. Thanks a lot bro's.
Awesome! Thank you!
Used to do it all the time. Colorado banned aircraft stripper. Now have to mechanically strip. Sucks. Good video.
Yes take your time and LET THE STRIPPER DO ALL THE WORK! LOL
Nice job, Not sure I missed it but what did you wash the hood with after using the stripper?
F'n awesome man ! excellent skills and knowledge TKO
Hello Brian, really liked you video. Looking for a good method for stripping and repainting Singer Featherweight sewing machines. Will the 'Aircraft Paint Remover' work with an aluminum frame machine or will it be to harsh a product?
Nice tips and a great how to! I tried a few paint removers but they preformed horrible due to new safety laws...
Brian
What brand of paint can pouring mixing lids do you use, on quart and gallon cans?
Idk this newer aircraft stripper doesnt work like it used to. I remember ooening the can to use it and any painted surface in a 20ft radius paint was curling and falling off just from the fumes that wofted around. I used the new stuff on my motorcycle to strip the paint. Even covered in plastic sheeting it didnt do anything at all.
Hi just a question what’s the best cleaning product for bare metal that gives me a day or 2 window before I lay down epoxy primer what cleans the residue of the paint stripper completely
Hey Brian, I recently clear coated a part using the extra slow reducer. The temperature was around 70 degrees in the shop, the clear coat laid down perfectly, and looked great until about 2 hours later it began to sag very slightly in one area. No big deal, I can get it out, but Im just curious as to why this may have happened, was it due to the usage of the extra slow reducer when the temperature was not very hot? Obviously laying it down heavy on the final coat likely contributed, but would using a slightly lower temp reducer help to prevent this?
Great video and exactly what I needed. You started to answer the question I had, but really didn't. Where in this process would you do the bondo? Bare metal or after epoxy? I have no history with epoxy so would like to do it the best way. Thanks so much for doing these !!
Epoxy it. Filler over epoxy. Then 2k urethane surfacer primer
B E A UTIFUL!!! you are the GOAT!!
Hey mr brian Do i need to prime in the same day that i sand the car or its normal to sanding and preparing the surface than prime it after few days ??
Hey Brian, for people who can’t get their hands on a mixer and all the different colors needed. Where do you recommend getting good matching paint?
Does the aircraft paint remover works on bumper as well since that is plastic?
After doing this epoxy primer, can I allow water or rain to hit it and paint it after let's say one or two weeks?
I haven’t used that stuff in a while but I think it says to neutralize the acid with water afterwards, and I don’t have a problem with etch priming the whole panel, seal, base,clear in same day. I don’t use sealer and epoxy together
I thought it would have had to be neutralized also, but don't have experience with that product. Strippers I use all need to be neutralized.
In Finland we got these 2k paints cans that mix as you use the spray by Maston. Unfortunately the ones I've bought have never worked properly.... I haven't read a single good review of these cans except for one guy in germany who used it and said it worked fine. But it's apparently a thing and I wished more companies would try that. I'd really like some long lasting 2k in a rattle can for small fixes.
Awesome job, product and especialy trainer !!!! Bravo 👏👏👏
Would this work on a repair to a fender that has an 8x12in scratch- already half of it is scratched down to bare metal? Thx!
Any thoughts on what might take off products such as DuraCoat and Cerakote? I have a slide for a pistol that i believe is DuraCoated, and Jasco paint stripper did absolutely nothing.
What undercoat would you use for an old car trailer resurface please.
Hello You make it easy for the do-it-yourself , By not skipping any Techniques great presentation! I'm an old school painter Have you ever hot potted synthetic enamel? Later
I found a down draft paint booth will help tons.
nice video
I am a little confused whats the difference between a sealer and an epoxy primer, primer is meant to protect the metal from rust then what purpose does the sealer serve
I got a question. Is mixing old paint with new a good idea? For instance, let's say you did a job with a specific paint code and years later, you have to do another job with that same paint code, but you don't have enough to do the whole job. You order more. Would it be a good idea to mix the new with the old?
Great video...is there a chance of "warping" an older (late 60's early 70's) hood by sanding ? or is it just the newer thinner hood...
Typically for me the only times things warp is if the sander gets the metal to hot but other than that it seems to be fine with normal pressure
Turco, Cee Bee , Ardox, Socomore A0103N, and Removall sv-35 were a few names we heard of
Does this work with the older style paints? I have a 1937 willys I need to strip down.
Hey can I try out your iwata series 2 base coat gun I just started painting and my dv1 I'm still paying off just keeps having problems
Thank you Sir for sharing skill and knowledge of this skilled work its very helpful. You are a master. More prosperity to you in ur work. Thanks.👍🏻👑👍🏻
I recently purchased a 1997 chevy 3500 . It apparently has galvanizing on the metal from the factory. How do I go about painting it?
I am thinking about doing this myself because I've gotten multiple quotes and they've come back over $15000. The paint just does not seem to be sticking to the metal anymore because of the galvanizing any ideas and pointers?
i am in the process of restoring a 1968 dodge charger and the paint is chipped and gone to hell, it has to be taken off. would you recommend sanding it off or using a liquid remover? i am a complete beginner and have no experience, so a walkthrough on what to do and products to use would be much appreciated
what do you guys do with all your extra paint? Do you just know how much to mix up from experience?
can this be used on fiberglass
Hey Brian, is this method good to try out on my integra, it only has primer sealer and I painted it about 2 years ago or more now so the paint is already dusting off or would it be better to sand down since it's only a thin coat and there's body work around the car? Thanks! Great video!
Try sanding first. Unless the parts are off the car. It can get messy
How would you strip paint off of fiberglass part ?
Does that work on an mtb frame that has been powdercoated?
Hello sir, I'm in the army and have been considering becoming a Collison repair tech. I'd like to be a paint tech specifically, pretty much what you do, I've considered going to a trade school and getting my education there. Is it possible to get a paint specific role, also what school program would you suggest. Thank you very much,
Back at it again 🤝
I needed a break lol
@@PaintSociety You deserved a break! Nobody works as hard as you.
We all working hard in different ways! Life catches up sometimes 😃
Can you paint a bumper cover with a 3 gallon compressor?!
How about a bumper cover that looks about like that....I have an OEM Honda bumper cover that was painted once 10 years ago and apparently not prepped well...Am I stuck sanding it all off or is there some stripper i can use? Or maybe just buy an aftermarket one for $150? It's a 2008 Accord coupe FWIW...