For the screws I make sure the spring tension is on the lowest just to make my tensioning consistent. I loosen the screws until it can corner cut past 45°. This makes it really fast wand way less blocky. Pretty much loses it till you start getting pops in solves then tighten it 1/8 turns untill the pops go away. Then once the screws are where I want them I’ll put the spring tension on 2. I then use 2 lubes that aren’t traditionally cube lubes (just what I have). It’s basically a combo of weight 2 and a very fast water based lube
The way I set my 10 rs3ms for multiblind up: loosen the screws 3/4 of a turn, spring tension on 2 clicks, so the 3rd weakest setting, a bit of weight 5 on the tracks and 6 deops of lunar on the pieces and whenever I find a side that has spring noise I add like 2 trops of nebular. Didn't want to spend the time lubing all the springs in all 10 cubes
I make sure my skews are at the very top right before they fall out then i remove all the prices then i rub them in sand and mud right before i re add the pieces i ben the green side 45° then i dip it in flour then i fry it and add sweet baby Ray's on it then i re add the pieces and i then add 100 drops of gan magic lube perfect set up :3
I prefer the heaviest lubes, like Vortex, on the spring and spindle. I didn't used thing that was this important until I had a WR M maglev 2020 that started to squeak. But, properly lubing the spindles effectively is best done with some disassembly, which probably ought to be done by only those who are mechanically inclined. And, you'll have to calibrate spindle screws, which is a whole different discussion.
For the tensions, I just check if all the screws look the same height (or gauge it with my finger over the screw cap), and after they are even, I see how many turns/half turns I need to get the best corner cutting - and then I adjust all the sides the same. Also, for the lube, I recommend always starting with two drops: one on a corner stalk and one on a piece. Add more if needed, but 6 drops can easily be too much.
@@randomqrcod.e if I can't feel any difference, I assume there's no difference. But in the original comment I wrote I check whether the screws _look_ the same height. If you're more pedantic, you can also take all the pieces out and count the threads visible.
the way i set my super rs3m is first, 2 drops of lunar on all the core. 8 drops of lumar and martian inside the cube, and 4 drops if moyu lube v3 for the quietness
My friend actually messed up with the screws and now his rs3m keeps getting popped. This is the reason I am afraid to touch the screw. The spring compression is set to 3 clicks not too fast not too slow. Pls recommend any other spring compression setting other than 3 clicks. I still have no lube
If possible, simply turn the screw clockwise the same amount that you initially unscrewed it. If not, you may have to play around with it a bit, making small screw adjustments at a time and twisting your puzzle until everything feels balanced :) ~Noah
Don't worry! Try to turn the screw the opposite direction the same amount, do some turns and adjust the screw properly until your cube feels even on all sides. Happy cubing! ~Noah
@SpeedCubeShopOfficial thanks so I kept turning the screws on each side and now they feel "mostly" the same, I feel like I would need a professional to do it for me just so I can get the best result but I think it's good enough for now
He is using the 2020 but the title says 2022.I am getting a 2022 and I want to learn how lube it properly. Is this the same tutorial for both of the cubes?
@@ahustle9783 I saw people in the Cubers subreddit say that while not necessary, it wouldn't hurt to lube at the screws, as apparently something stuff can rub against the plastic in Moyu MagLev cubes.
I tried to adjust my cube, because it was my first speed cube, and now I feel like every time I try to loosen it, it is to loose and not fast, but when I tighten it, it becomes sluggish.
you know when speedcubeshop uploads its going to be a banger
For the screws I make sure the spring tension is on the lowest just to make my tensioning consistent. I loosen the screws until it can corner cut past 45°. This makes it really fast wand way less blocky. Pretty much loses it till you start getting pops in solves then tighten it 1/8 turns untill the pops go away. Then once the screws are where I want them I’ll put the spring tension on 2. I then use 2 lubes that aren’t traditionally cube lubes (just what I have). It’s basically a combo of weight 2 and a very fast water based lube
I'm going to do dis right now
best tutorial for 'moyu cubes' user❤❤
I love how they made these vids so simple.
thanks a lot❤ and love you from Bangladesh💚❤💚🙂
The way I set my 10 rs3ms for multiblind up: loosen the screws 3/4 of a turn, spring tension on 2 clicks, so the 3rd weakest setting, a bit of weight 5 on the tracks and 6 deops of lunar on the pieces and whenever I find a side that has spring noise I add like 2 trops of nebular. Didn't want to spend the time lubing all the springs in all 10 cubes
What spring compression? I like the 3
@@v1ncy982 oh true, forget to mention that, I updated my comment now
I make sure my skews are at the very top right before they fall out then i remove all the prices then i rub them in sand and mud right before i re add the pieces i ben the green side 45° then i dip it in flour then i fry it and add sweet baby Ray's on it then i re add the pieces and i then add 100 drops of gan magic lube perfect set up :3
@@atom1kcreeper605 this is cursed
Idk what i should work on my f2l or music or both idk
Ayeee I think im gonna buy rs3m 2022 on christmas!
Thx you helped me veary much with my moyu rs3m i didnt know what the blue transparet screwdriver do and how do i resetit
I prefer the heaviest lubes, like Vortex, on the spring and spindle. I didn't used thing that was this important until I had a WR M maglev 2020 that started to squeak. But, properly lubing the spindles effectively is best done with some disassembly, which probably ought to be done by only those who are mechanically inclined. And, you'll have to calibrate spindle screws, which is a whole different discussion.
Great tutorial for the Moyu, thanks!
Thank bro this helps out and set my new personal record on this
We're happy to help! Congrats on your PB!
~Noah
What’s ur pb? And what kind of lube did u use
For the tensions, I just check if all the screws look the same height (or gauge it with my finger over the screw cap), and after they are even, I see how many turns/half turns I need to get the best corner cutting - and then I adjust all the sides the same.
Also, for the lube, I recommend always starting with two drops: one on a corner stalk and one on a piece. Add more if needed, but 6 drops can easily be too much.
yeah, I do the same for the screw depth.
A problem with this method is the screw length may not be the same on all the screws from the factory.
@@randomqrcod.e if I can't feel any difference, I assume there's no difference. But in the original comment I wrote I check whether the screws _look_ the same height.
If you're more pedantic, you can also take all the pieces out and count the threads visible.
I got a SpeedCubeShop ad before I watched this video
nice video! Happy Holidays!
Gonna be useful, thanks!
Avoiding eye contact like a real cuber
Actually
Faxxxxxxxxx
I bought this cube a my first speed cube ever
super nice vid stay as you are ❤️🔥
This helped alot!!
God vid, this was so useful thanks
Can i use the galaxy lube in both the core and the pieces?
yep, you totally could. All of this comes down to how you like it
nice setup :)
the way i set my super rs3m is first, 2 drops of lunar on all the core. 8 drops of lumar and martian inside the cube, and 4 drops if moyu lube v3 for the quietness
Adding magnets is a must tbh.
Yeah the magnets are pretty weak on the rs3m
Also , please tell me what should I do if the screws become loose eventually. I mean should i tighten to the half or the quarter?
how i set it up:
adjust screws and tension to how i like it
add xmt
done
My friend actually messed up with the screws and now his rs3m keeps getting popped. This is the reason I am afraid to touch the screw. The spring compression is set to 3 clicks not too fast not too slow. Pls recommend any other spring compression setting other than 3 clicks. I still have no lube
I think without lube this cube is good in 2 or 3 clicks. I like mine with 2 clicks before i give it lube. Now i use 6 clicks after i lube it
same happened to my rs3m and wrm
Setting 3 is fine, you should consider getting lubes it improves your cube s ton!
@@mynameisnonofyourconcern9715 thanks a lot for your suggestion
@@etereall thank you for the tips
Thank you very very very very very very very very very very much
what are the requirements for a sponsership?
I think the name of the video is wrong - the "buy" link leads to rs3m 2020, not 2022.
The cube should be the 2020 version
The buy link leads to the 2020 version (Maybe they already changed it)
Uhm I might turned on the screws randomly how do I get them equal again, it’s my first speedcube that I need to adjust
If possible, simply turn the screw clockwise the same amount that you initially unscrewed it. If not, you may have to play around with it a bit, making small screw adjustments at a time and twisting your puzzle until everything feels balanced :)
~Noah
@@SpeedCubeShopOfficial thank you!
Can you guys do the gan 13 M next plz?
Can you lube your cube with oil
Thanks!
How were the brownies
Is it ok if I use Martian for the core lube?
How to remove scratches and dents(white marks when you drop it) on my Rs3M?
Thank u
May i ask, will the springs rust if i add lube in the springs, as i asked someone who knows stuff about lubing said to not add any to the springs.
Hmm idk but i think u should
Try mscube ms3l standard
What if i accidentally turned it with the screw before a tutorial
Don't worry! Try to turn the screw the opposite direction the same amount, do some turns and adjust the screw properly until your cube feels even on all sides. Happy cubing!
~Noah
@SpeedCubeShopOfficial thanks so I kept turning the screws on each side and now they feel "mostly" the same, I feel like I would need a professional to do it for me just so I can get the best result but I think it's good enough for now
He is using the 2020 but the title says 2022.I am getting a 2022 and I want to learn how lube it properly. Is this the same tutorial for both of the cubes?
this works for any cube
@@urakov889 ok but what about the springs part because the one I’m getting does not have springs.
@@ahustle9783 I saw people in the Cubers subreddit say that while not necessary, it wouldn't hurt to lube at the screws, as apparently something stuff can rub against the plastic in Moyu MagLev cubes.
Can i put qiyi mofangge in the spring
Can you sent cube to indonesia?
Do you ship to Bangladesh?
I think they are international
You got your answer 1 year later😂
How about Super rs3m
Hello, SCS, J perm has not been posting anything for over a month. Is everything ok on his side? Do you know when he will be coming back?
Says to do 10 U2’s and then does 18
nice
I tried to adjust my cube, because it was my first speed cube, and now I feel like every time I try to loosen it, it is to loose and not fast, but when I tighten it, it becomes sluggish.
Is the rs3 m 2022 the super rs3 m? edit: the centre caps look like the 2020... not sure which one it is
Yo
cool
man, disappointed that it's not the super rs3m but it's fine I guess
I HATE RS3M 2020 as the problem of screw falling out
1:38
thats the 2020 not the 2022
outdated video
third
early
second
fourth
Eighth*
Can you lube your cube with oil
No.
Yo