(006) Install Yoshimura Fender Eliminator: 21-24

This video is dedicated to the 21-24 #NinjaZX10R Transformation Modifications Video Series. In this video I'll be removing the stock fender tail and replacing it with a Yoshimura fender eliminator. There'll be some wiring and innovative thinking when it comes to routing the connectors.
Hope you enjoy! Be sure to leave a Comment, Like, Share, Subscribe, and Ring that Notification Bell so you're notified about the next upload.
Parts:
- Yoshimura ZX10R 16-21 Fender Eliminator Kit / Kawasaki Suzuki of Rome, GA / PN: 796358
- Marine Heat-Shrink Tubing Assortment (42 PC.) / Storehouse / Harbor Freight / PN: 67598
Chapters:
0:00 - Chapter Title / Intro Splash
1:08 - Remove Stock Fender Tail
18:19 - Install Yoshimura Fender Eliminator
Check out my other uploaded videos in this series from the Play List Link below:
21-24 ZX10R Transformation Modifications Video Series Playlist: • 21-24 ZX10R Transforma...
Or click on the link at the end of the titles below to go directly to the video you want:
(000) Downloadable Detailed Instructions • (000) Downloadable Det...
(001) Introduction to the NINJAof1 Channel • (001) Intro to the NIN...
(002) The Preparation Stage • (002) The Preparation ...
(003) Disassembly of Fairings • (003) Disassembly of F...
(004) Final Disassembly • (004) Final Disassembl...
(005) Remove ECU & Mail to Moore Mafia to be Flashed • (005) Remove ECU & Mai...
(006) Install Yoshimura Fender Eliminator • (006) Install Yoshimur...
(007) Remove Muffler and Install SC Project • (007) Remove Muffler a...
(008) Passenger Foot Peg Brackets w/Bonus • (008) Passenger Foot P...
(009) Remove Pair Valve Plates • (009) Remove Pair Valv...
(010) Remove Hoses/Cap Off Throttle Bodies • (010) Remove Hoses/Cap...
(011) Install Air Box/BMC Race Air Filter • (011) Install Air Box/...
(012) Final Emission Deletion • (012) Final Emission D...
(013) Fuel Tank/ECU/Startup/Clear Errors • (013) Install Fuel Tan...
(014) Install Tail Cowl/Pillion Seat Cover • (014) Install Tail Cow...
(015) Install Radiator/Oil Cooler Guards • (015) Install Radiator...
(016) Assembly of Fairings • (016) Assembly of Fair...
(017) 22 ZX10R After Mods Ride w/Talladega Track Day • (017) 22 ZX10R After M...

[@jayilla28]

So would you recommend making the hole in the bracket bigger for the wires or would you still shave the connectors to fit them through?

[@NINJAof1]

I only had to shave down just a little from the sides of the Blue and Black connectors for the turn signals. I just stayed away from where the detent tab was so it would still be functional and lock. I think if you tried to make the hole bigger it may bend or distort the bracket. If I had to do it again, I'd do it the same way as the video.
After shaving down the sides of the turn signal connectors I put those through the hole first then the license plate light connector last. Not having the license plate wire in gives you just enough room to slide the shaved-down turn signal connectors. Hope that helps. Thank you.

[@jayilla28]

@@NINJAof1 ok, I’m about to jack it all up but…

[@NINJAof1]

Just take your time. You'll never have to mess with routing the connectors through the hole again. Even when you take the bracket off for a track day, you can disconnect them and remove the entire assembly. That's what I did last track day.