I really appreciate the awesome tips and ideas for newbie cabinet makers. You and Jason, also known as Bourbon Moth, should totally team up for an episode together!
Been building furniture for 65 years, Just hit "follow" on your podcast. We do a lot of the things using the same jigs, but you gave me some great ideas, esp for drawer slides; a lot of jigs are about to get "tossed". As a 75-year-old, the issue is getting too set in "old ways"; it's all about jigs, efficiency, accuracy, and repeatability. Great job!! TJ Holt
Thank you SO MUCH for doing these videos! I cannot tell you what a help it is going to be for me. I am sixty years old, and my husband is 78 and we have to build our own cabinets because we cannot afford to pay 30k which was the quote we got from Home Depot, which included an almost 10k install. You would think that we lived in a mansion with a two kitchens at that price, but this quote was for a 3/2 bath in Northern CA. Yep. I am starting a new career as a cabinet builder at 69 years old. I will also be doing my own plumbing and landscaping as well as laying my own pavers. I am excited about it and nervous. But I have no choice but to do everything myself with what these people are trying to get out of me. Wish me luck! Thanks Again!
This came across my feed at the perfect time. I just go into woodworking a friend just asked me to help him build cabinets. So this is some great advice at just the right time for me!
The shop I run is in the basement of a large gothic chapel. When I get ply it has to be carried all the way around the building, along a rear walkway, into the basement and then the storage. I had a gripper thing, but recently I bought a little wheel thingy from Home Depot. It sits under the middle of the sheet/sheets, and steers easy on pneumatic tires. Love it. Also, on the subject of plywood thickness and dados, I’ve had a LOT of variability in the last few years. All the way from too thin (under 23/32) to full 3/4”. And I’ve been burned a couple times because of that. Not sure what’s going on. All sheets from the same supplier. Great video and full of good advice. FWIW, I cut my toe kicks too 😂. Been doing this for forty years and never had any use for separate kicks.
Your comments are appreciated. One thing that might be more suited your construction video than tool video, is a story-pole. I had to build 4 identical cabinets containing 5 drawers each. By using my story-pole I guaranteed that my layout matched side to side. Love your video. Keep making sawdust!
Story poles are nice for sure but It doesn't completely solve the problem the way a scrap spacer does. You can make your marks accurately but you still have to ensure the slide is mounted and installed level and accurate to the lines. With a scrap spacer there's no trying it just holds it in perfect position for you!
Thats a really useful vid for some who has to compromise on their tools, and tools at reasonable prices are readily available now - just remember to upgrade the blade. I remember buying a track saw and not using it much as the table saw sufficed. Then I had sheet materials to contend with, I made a MFT and the great thing about a track saw is the ability to do repeatable and accurate cuts. Thanks for posting. Regards Mike
I have most of these, I’ve never built cabinets before until this year. A track saw is the way to go. My cuts, and fit looked so good. I got the Milwaukee, even though I’m a dewalt fan. I just thought it was better. I made the mistake of not having the back in the track a few times and cut into my splinter guard. But was still able to use it, and once I knew that I had that out of my system, I changed the guard and haven’t done it since. Really happy with it, and a lot of those other jigs.
Your video's are so informative AND entertaining. I bet your sense of humor drives your wife crazy. I am right with you on most of the jigs and router bits to fit the plywood you are using. I just got a Domino 500 and learning how to operate it by making narrow scraps into wider scraps to make a lot of useful things like spacers. Keep doing what you are doing, its working.
Great video mate! I’m new to fine wood working and the sort that would spend lots on unnecessary stuff. It’s good to know I can get started without buying everything! Thanks.
Funny, I have every single jig /tool you showed. I do make a ton of cabinets and have found on my own that these tools make my cabinet making much easier than not having them. Enjoyed your video.😃
I love this video! My husband and I will be building the cabinets for our kitchen (after he is done rebuilding his 1956 Chevy pickup), so this was perfect. I definitely will be checking out your other videos, too. Thank you!
You, sir, are a genius! You build cabinets almost exactly as I do. However, I did not take out a second mortgage on my house to buy a Festool track saw. Excellent video.👍
Thanks for doing such great videos. I am planning on converting a single car garage into a woodworking shop. I have now watched 4 of your videos and looking forward to using your great ideas for rookies like me.
Thank you for all of the cabinet tips. I'll be building my first ever drawers soon, and I really appreciate the advice on slide location! I had no clue. Thanks again. 😃😃😃😃😃❤️❤️❤️❤️❤️
Good video. 5:50 I think it's worth mentioning that sometimes plywood does come in the full size (but it is rare) - I ran into an issue where I ended up buying both full size 3/4 bits as well as undersized 3/4 bits from where I had bought plywood from two different suppliers.
A really nice video with lots of good info. I just finished a pot drawer with an internal drawer and could have used some of his advice then. It would have been an easier project if I had known.
I really like this video. Some of it I knew but there was a lot of good ideas that just never occurred to me. I'm ready to hurt myself emotionally making drawers with side mount slides again
Man! I have everything on your list. Share the same opinions too; right down to the unused Centipede accessories and the hinge jig-yeah, glide jig-nay. Amazing. 🤔😂😁
Fantastic tips, man! Thanks a bunch! 😊 For now I'm planning on building one set of cabinets... But who knows about the future, right? Anyway, stay safe there with your family! 🖖😊
Try a UK single garage workshop. I can't find space to store a centipede and 8x4 insulation sheet. And the Kreg Accu-Cut plus your circular saw will give amazing results if you can't justify a Festool track saw. Other brands are available.
Common Sense Video, just right for me. Besides, you have a good sense of humor!! I bought two sheets of Baltic Plywood to make dovetail drawers. Thu runouts and wood chipping stopped my project in its track and used the plywood for who knows what. Do you have a video on that subject or is it better to use soem hardwood? Thank you.
Was just about to buy those drawer guide jigs, helpful to know that just the method used now with scrap is really just the best way, makes sense. Thanks for the video! Do you have a video on that pocket hole jig?
Great video. In most videos de brand Wen js popping up. Maar the are even more cheaper en better brands than Wen. Like example einhell, skil. Sheppach and Parkside. They are cheaper and look better than Wen. But I live in Europe NL so maybe those brands aren't in the states.
The problem with the KREG hinge hole drilling jig its not really made for doing a large amount of doors at once. Its really a hobbyist tool. Reason being the hole the boring bit goes thru isnt lined with metal so as it gets hot itll warp that hole. Happened to me so i bought an actual machine lol and getting the wood shavings out of the guard is a HUGE PITA
Yeah I don't disagree but compared to the cost of a hinge boring machine most viewers will only relate to the Kreg which will do great if all you ever want to do is build one set of cabinets!
Please share more info about the cleantec cart and separator. I built a cart for a ridgid vac with a dustopper, would like to do something similar to yours for my CT Midi
I love to see that thanks to American Imperial system manufacture BS they need to sell you a new router bit just because... you know... does not fit 😋😂... Amazing video by the way. ☺👍
have you tried using two dominos and pocket holes? The dominos mostly just to prevent the plywood from moving when putting in the pocket hole screws. I think I'm going to give it a try, because I can't seem to put together a pocket hole without it moving a bunch on me.
$210 for the centipede and $60 for the magswitch! I'm retired and a hobbyist woodworker, I mostly do this for gifts and some small sales at craft fairs. These things though they might be convenient as all hell, they are way out of my price range.
What about the inner part of euro hinges? I spent several hours at trial and error with scraps, but I know that there must be a "right" way to position those.
I love your videos. However, I am more a fan of a separate toe-kick base. You create one base for all cabinets, level it and affix it. Then you just set all of your cabinets on top of the toe-kick base. But, again, great video.
separate toe kicks are great when doing long runs of cabinets! I find most of the time this not to be the case. There's always a fridge or dishwasher etc breaking up the flow and then separate toe kicks become more work than they are worth.
What kind of plywood do you prefer, and what does a 4x8 sheet of it usually cost? I'm trying to make sure that a) I find good products and b) I'm finding it at a reasonable price.
@@MWAWoodworks I personally love them, just 10 minutes ago we found one with a bunch of babies on her back. They are absolutely beautiful little creatures
I won't say that I love them and I control the population because I don't want an infestation however they do keep the bad spiders away so we coexist 🤣
I’d argue pocket holes and dados are completely unnecessary in general cabinet building. Just screw through the sides using the countersink bit. Maybe a couple of brad nails first to help hold in place if you like. Then screw your back on which if cut square will pull the cabinet square
Yeah just depends on the application. I did mention that screwing into the face is a good way to go if the application is right and they won't be seen.
I started making my own kitchen cabinets and that was one of my main takeaways from other UA-cam channels like Sedgetools and Brents Woodworking. It’s so easy to level the toe kick platform instead of each cabinet.
It took me about 30 years to finally try separate toe-kicks. Being stuck in that "rut" cost me hundreds of hours of frustration, time and money. I first tried it on my neighbor's garage cabinets. DUH!! I never went back to the old way. Thx.
@@MWAWoodworks There we disagree. I think build elegance is more about the craftsman than the piece. I use phs from time to time, but honestly I never found the joinery nearly as appealing as using dowels or tenons. There's something about building quality pieces, no matter their intended use. My $0.02
No worries. I just disagree that pocket holes make it less quality. I've made cabinets with my domino and with my pocket hole jig. They look and function identically, no difference in quality and any user of the cabinets would never know what joinery was used to build them.
Fyi on all easy carry handles - getting up steps does not work. You have to press the thing all the way over your head. Without steps, yes. Industrial jointer, table saw and then just a few more thousand for the rest. Then you need a wide open shop space. At that point you are 50 and if you didnt find a wife and make some babies you now instead have a garage full of tools and the Merc sits in the driveway all winter.
That American adhesion to the imperial system is why you think three-quarter inch plywood is undersized. Plywood is usually 18mm, which is 0.7 of an inch, not 0.75. The answer is to buy an 18mm router bit.
18mm is not the answer to anything. US ply is well over 18mm, more like 18.5mm and the Baltic birch I get from Europe is consistently 17.75mm Plywood is given a nominal dimension whether that be 3/4 or 18mm. In both cases the actual plywood is smaller. Just like a 2x4 is actually 1.5x3.5
You were doing great right up until you said "Pocket Screws". I find the lock miter to be quick and the strongest. Btw, if you are a multi media worker and you weld, you probably already have several magnetic triangles you can use for the stops. However if the table is aluminum eerht...no go. You can opt for a suction cup gripper like you use to pick up sheet goods and glass panes. There is something to be said as a matter of pride and accomplishment for making your own custom jigs. By the way KREG did not sponsor these comments.
I hate my gator lilft and never use it. It's just not a omfy way to carry plywood. Unless you're going to build a tonne of cabinets, you dont need a track saw at all and can do just fine with a very cheap diy version
You’re handling the plywood too many times, put one corner against the fence and lift the opposite bottom corner and make your cut, I would cut it right after taking it out of your truck. You should look into building separate toe kicks, you walk into the kitchen level all the kicks and start putting cabinets on them.
@@MWAWoodworks no problem, I am a fine woodworker that’s retired now, I’m just saying what works for me. I’m also 70 and can still cut 3/4 MDF with no problems. Have a great day
There is a huge difference between building a few cabinets for your shop and being a cabinet maker. You do need a table saw, no matter how much you are getting paid to sell track saws.
@@MWAWoodworks Yeah, I was suprised. Had my iron, dropped it the shop one last time and had the mini for T's and hats and stuff. It worked so much better. It's smaller, fits perfect over 3/4", has a cool little stand to put in on when it's hot, has a small footprint on my workbench meaning I don't bump into the hot iron anymore and it's also perfect for dents. A little water over the dent, a piece of teflon heat protector and bye-bye dent.
WHAT NEXT?
✅Join my Patreon community: patreon.com/MWAWoodworks
✅Learn even more about cabinet making! ua-cam.com/play/PLTGU37t015kng61D5cjPei-26UFz6VXOx.html
✅ CABINET PROJECT PLANS
Cabinet Plan Bundle - mwawoodworks.com/product/the-cabinet-bundle-save-20/
Base Cabinets: mwawoodworks.com/product/base-cabinet-plans/
Upper Cabinets - mwawoodworks.com/product/upper-cabinet-plans/
Three Drawer Cabinet: mwawoodworks.com/product/3-drawer-base-cabinet-plans/
Tall Pantry Cabinet- mwawoodworks.com/product/tall-pantry-storage-cabinet/
Kitchen Island - mwawoodworks.com/product/kitchen-island/
Tall Storage Cabinet - mwawoodworks.com/product/tall-storage-cabinet/
✅ TOOLS AND SUPPLIES IN THIS VIDEO
JessEm Dowelling Jig - amzn.to/3XMxeFQ
Dovetail Jig - amzn.to/3YcteQN
My favorite Pocket Hole Jig - amzn.to/3N4MBET
Box Joint Jig - amzn.to/3N4tpHe
My favorite persuader (mallet) - amzn.to/3zApkrk
Lock Miter Router Bit - amzn.to/3N5o96s
Lock Miter Setup Jig - amzn.to/3ZHGUnW
Locking Rabbet Router Bit - amzn.to/3N1Yrzo
Euro glides - amzn.to/4eIrcNC
Side mount Slides - amzn.to/3TLkoqi
Under mount Slides - amzn.to/3N1sffN
DeWalt Cordless Palm Router - amzn.to/3zC8oR8
Milwaukee Detail Sander - amzn.to/3XYMjWm
Festool Domino - amzn.to/4exVi6m
Gator Lift - amzn.to/4cJCJuG
Bora Centipede - tsoproducts.com/accessories/bora-centipede-4x8-foot-unit-with-4-x-cups-4-clamps-carry-bag/?ref=MWAWW
Festool Track Saw - amzn.to/4dVPjb6
Kreg Track Saw (budget friendly saw) - amzn.to/3T4ybYQ
WEN Track Saw (entry level saw) - amzn.to/3T0X2g7
Track Saw Square - tsoproducts.com/tso-guide-rail-squares/grs-16-pe-parallel-edge-guide-rail-square/?ref=MWAWW
Carpenter’s Speed Square - amzn.to/4cLPgh0
Jig Saw - amzn.to/474WMlO
Mag Switch - amzn.to/4cJVmyD
Undersized Plywood Router Bits - amzn.to/4dZnpeh
Pocket Hole Jig - amzn.to/3Z7qPHA
Countersink Drill Bit - amzn.to/470sErO
Edge Banding Speed Roller - amzn.to/4fZsuoQ
Flush Cut Trimmer - amzn.to/3X0vl8g
Edge Banding Quad Trimmer - amzn.to/3MiYWoF
Replacement Blades - amzn.to/4dBBnU4
Concealed (Euro) Hinge Jig - amzn.to/4dJtT1q
Shelf Pin Jig - amzn.to/4dZvP5r
True Position Cabinet Hardware Jig - amzn.to/4fY2OJf
I really appreciate the awesome tips and ideas for newbie cabinet makers.
You and Jason, also known as Bourbon Moth, should totally team up for an episode together!
Really enjoying your clear, common-sense, thorough content.
Thanks for the kind words!
This video didn't make me angry with disgust. Thumbs up.
Been building furniture for 65 years,
Just hit "follow" on your podcast.
We do a lot of the things using the same jigs, but you gave me some great ideas, esp for drawer slides; a lot of jigs are about to get "tossed".
As a 75-year-old, the issue is getting too set in "old ways"; it's all about jigs, efficiency, accuracy, and repeatability.
Great job!!
TJ Holt
Thank you SO MUCH for doing these videos! I cannot tell you what a help it is going to be for me. I am sixty years old, and my husband is 78 and we have to build our own cabinets because we cannot afford to pay 30k which was the quote we got from Home Depot, which included an almost 10k install. You would think that we lived in a mansion with a two kitchens at that price, but this quote was for a 3/2 bath in Northern CA. Yep. I am starting a new career as a cabinet builder at 69 years old. I will also be doing my own plumbing and landscaping as well as laying my own pavers. I am excited about it and nervous. But I have no choice but to do everything myself with what these people are trying to get out of me. Wish me luck! Thanks Again!
As always, you are concise, informative, honest - and funny. Thank you!!!
Appreciate all those kind words! 😁
This came across my feed at the perfect time. I just go into woodworking a friend just asked me to help him build cabinets. So this is some great advice at just the right time for me!
YOU SIR.......need to be rewarded a medal for helping people with cheap options. Thank you!
Excellent content!! No nonsense, straight-up clear and useful information. Well done.
Thanks so much!
Two of my favourite wood workers in one video!
The shop I run is in the basement of a large gothic chapel. When I get ply it has to be carried all the way around the building, along a rear walkway, into the basement and then the storage. I had a gripper thing, but recently I bought a little wheel thingy from Home Depot. It sits under the middle of the sheet/sheets, and steers easy on pneumatic tires. Love it.
Also, on the subject of plywood thickness and dados, I’ve had a LOT of variability in the last few years. All the way from too thin (under 23/32) to full 3/4”. And I’ve been burned a couple times because of that. Not sure what’s going on. All sheets from the same supplier.
Great video and full of good advice. FWIW, I cut my toe kicks too 😂. Been doing this for forty years and never had any use for separate kicks.
Your comments are appreciated. One thing that might be more suited your construction video than tool video, is a story-pole. I had to build 4 identical cabinets containing 5 drawers each. By using my story-pole I guaranteed that my layout matched side to side. Love your video. Keep making sawdust!
Story poles are nice for sure but It doesn't completely solve the problem the way a scrap spacer does. You can make your marks accurately but you still have to ensure the slide is mounted and installed level and accurate to the lines. With a scrap spacer there's no trying it just holds it in perfect position for you!
Thats a really useful vid for some who has to compromise on their tools, and tools at reasonable prices are readily available now - just remember to upgrade the blade. I remember buying a track saw and not using it much as the table saw sufficed. Then I had sheet materials to contend with, I made a MFT and the great thing about a track saw is the ability to do repeatable and accurate cuts. Thanks for posting. Regards Mike
I have most of these, I’ve never built cabinets before until this year. A track saw is the way to go. My cuts, and fit looked so good. I got the Milwaukee, even though I’m a dewalt fan. I just thought it was better. I made the mistake of not having the back in the track a few times and cut into my splinter guard. But was still able to use it, and once I knew that I had that out of my system, I changed the guard and haven’t done it since. Really happy with it, and a lot of those other jigs.
Your video's are so informative AND entertaining. I bet your sense of humor drives your wife crazy. I am right with you on most of the jigs and router bits to fit the plywood you are using. I just got a Domino 500 and learning how to operate it by making narrow scraps into wider scraps to make a lot of useful things like spacers. Keep doing what you are doing, its working.
Great video mate! I’m new to fine wood working and the sort that would spend lots on unnecessary stuff. It’s good to know I can get started without buying everything! Thanks.
It's more fun buying all the stuff but you have to start somewhere 😂😂😂
@ so true! Maybe you should do a video for wive’s explaining in women terms how all these toys are an investment 🤣.
Very clear and honest video. Thank you!
Funny, I have every single jig /tool you showed. I do make a ton of cabinets and have found on my own that these tools make my cabinet making much easier than not having them. Enjoyed your video.😃
I love this video! My husband and I will be building the cabinets for our kitchen (after he is done rebuilding his 1956 Chevy pickup), so this was perfect. I definitely will be checking out your other videos, too. Thank you!
Nice video Matt!! Very clear and concise. Hope you’re doing well!!
thank you my friend! You as well!
You, sir, are a genius! You build cabinets almost exactly as I do. However, I did not take out a second mortgage on my house to buy a Festool track saw. Excellent video.👍
Thanks!
Thanks for doing such great videos. I am planning on converting a single car garage into a woodworking shop. I have now watched 4 of your videos and looking forward to using your great ideas for rookies like me.
Thank you for all of the cabinet tips. I'll be building my first ever drawers soon, and I really appreciate the advice on slide location! I had no clue. Thanks again. 😃😃😃😃😃❤️❤️❤️❤️❤️
Awesome!
@@MWAWoodworks 😊😊
Good video. 5:50 I think it's worth mentioning that sometimes plywood does come in the full size (but it is rare) - I ran into an issue where I ended up buying both full size 3/4 bits as well as undersized 3/4 bits from where I had bought plywood from two different suppliers.
Great Content, you’re very informative and helpful 🙏 your videos changed my life thank you
A really nice video with lots of good info. I just finished a pot drawer with an internal drawer and could have used some of his advice then. It would have been an easier project if I had known.
I really like this video. Some of it I knew but there was a lot of good ideas that just never occurred to me. I'm ready to hurt myself emotionally making drawers with side mount slides again
The potato chip metaphor is perfect for cabinet making…can’t believe that I have that same sunbeam iron in my shop for gluing the end strips on.
The image of you on the top of the plywood just won a subscribe from me
Love it. Straight to the point.
Just perfect. Thank you! :)
Awesome 👍
I really like the stop block method of setting the draw slides, it's full proof.
Tamar? Is that you???
For sure! My favorite.
@@MWAWoodworkshe said “draw” slides like Tamar from 3x3 says it 🤣
I first saw this trick used by Norm Abram on New Yankee Workshop, he did it that way many times.
It is full proof and stupid simple. It is therefor the PERFECT solution. Of course that plywood better be perfect.
Great video as always I always feel like I learn so much from watching you videos Thanks as always for sharing your knowledge.
You just gained another follower!! Great video!
Ha awesome!
One of your best! Thank you.
@MWA - Excellent video, Sir. 👍
Thank you!
Man! I have everything on your list. Share the same opinions too; right down to the unused Centipede accessories and the hinge jig-yeah, glide jig-nay. Amazing. 🤔😂😁
Great minds think alike 😂
Fantastic tips, man! Thanks a bunch! 😊
For now I'm planning on building one set of cabinets... But who knows about the future, right?
Anyway, stay safe there with your family! 🖖😊
Thanks brother!
Very helpful. Thank you.👍
Very useful, thanks 🙂
Great video, thank you!
Awesome video, Thank you
Thanks 😁
Try a UK single garage workshop. I can't find space to store a centipede and 8x4 insulation sheet.
And the Kreg Accu-Cut plus your circular saw will give amazing results if you can't justify a Festool track saw. Other brands are available.
You lost me at UK 😂😂🤣🤣🤣🤣
Thank you very much for sharing. Great info. Subscribed!
Thanks for the sub!
Common Sense Video, just right for me. Besides, you have a good sense of humor!! I bought two sheets of Baltic Plywood to make dovetail drawers. Thu runouts and wood chipping stopped my project in its track and used the plywood for who knows what. Do you have a video on that subject or is it better to use soem hardwood? Thank you.
I've never cut dovetails in plywood 🤷
Was just about to buy those drawer guide jigs, helpful to know that just the method used now with scrap is really just the best way, makes sense. Thanks for the video! Do you have a video on that pocket hole jig?
Do you mean the jig itself or the platform I made for it? I did a video on the jig already but not the base.
You're so good at this. I just wish that I had met you earlier in life :-)
Always great stuff, thanks again 😊
Great video !
Thanks!
Pocket screws are so nice.
Nice list.
Yeah, this is great.
👍
For plywood spacers, I can't count the times that I've glued scraps together to make the spacer.
For sure. Plywood spacers are a great "free" jig
great content
Great video. In most videos de brand Wen js popping up. Maar the are even more cheaper en better brands than Wen. Like example einhell, skil. Sheppach and Parkside. They are cheaper and look better than Wen. But I live in Europe NL so maybe those brands aren't in the states.
Seria bueno que haga una revision de lo mismo pero en Aliexpress hay las mismas herramientas pero en aluminio y se ven de calidad.
Sunday. Chill day. Foot bath. Watching UA-cam… IS THST A F*%KING CORDLESS IRON!?!
BRB Amazon.
Hahaha no it was not a cordless iron!
The problem with the KREG hinge hole drilling jig its not really made for doing a large amount of doors at once. Its really a hobbyist tool. Reason being the hole the boring bit goes thru isnt lined with metal so as it gets hot itll warp that hole. Happened to me so i bought an actual machine lol and getting the wood shavings out of the guard is a HUGE PITA
Yeah I don't disagree but compared to the cost of a hinge boring machine most viewers will only relate to the Kreg which will do great if all you ever want to do is build one set of cabinets!
@@MWAWoodworks I agree 100% its a great on site tool as well. Kregs portability overall is unmatched
Please share more info about the cleantec cart and separator. I built a cart for a ridgid vac with a dustopper, would like to do something similar to yours for my CT Midi
I have videos on my channel for both the dust collection carts I built 👍
Can each leg on the accordion table be adjusted for height? Also mag switch needs a dust chamfer.
Any favorite jigs or tools for installing drawer fronts on frameless cabinets or just double sided tape and spacers?
I love to see that thanks to American Imperial system manufacture BS they need to sell you a new router bit just because... you know... does not fit 😋😂... Amazing video by the way. ☺👍
do you have a video focused only on drawer slide installation? I would love that
What specifically? Im working on a video all about drawers.
Very good points
Great information.
You for to mention a big item. Where do you buy your pre finished plywood?
I buy it locally in Nashville. A couple places sell it.
The "pink" foam also prevent most tear out from under the cut. Love that pocket hole jig. 32 or 36 inches long?
The pink foam is a game changer
have you tried using two dominos and pocket holes? The dominos mostly just to prevent the plywood from moving when putting in the pocket hole screws. I think I'm going to give it a try, because I can't seem to put together a pocket hole without it moving a bunch on me.
I think I would break the internet if I tried that 🤣🤣🤣
$210 for the centipede and $60 for the magswitch! I'm retired and a hobbyist woodworker, I mostly do this for gifts and some small sales at craft fairs. These things though they might be convenient as all hell, they are way out of my price range.
What about the inner part of euro hinges? I spent several hours at trial and error with scraps, but I know that there must be a "right" way to position those.
watch my "Cabinetmakers hate me" video. I covered the cabinet side of hinges in there!
I love your videos. However, I am more a fan of a separate toe-kick base. You create one base for all cabinets, level it and affix it. Then you just set all of your cabinets on top of the toe-kick base. But, again, great video.
separate toe kicks are great when doing long runs of cabinets! I find most of the time this not to be the case. There's always a fridge or dishwasher etc breaking up the flow and then separate toe kicks become more work than they are worth.
What kind of plywood do you prefer, and what does a 4x8 sheet of it usually cost? I'm trying to make sure that a) I find good products and b) I'm finding it at a reasonable price.
for my cabinetry projects I buy prefinished maple ply from Purebond/Columbia Forest Products or from Garnica. usually runs 90 per sheet for 3/4
@@MWAWoodworks thanks!
2:46 don’t worry, if it’s just wolf spiders you’re safe, wolf spiders aren’t aggressive of deadly (at least all the species I know of aren’t 😅)
Oh I know. They live in my shop 😀
@@MWAWoodworks I personally love them, just 10 minutes ago we found one with a bunch of babies on her back. They are absolutely beautiful little creatures
I won't say that I love them and I control the population because I don't want an infestation however they do keep the bad spiders away so we coexist 🤣
Do you have a build video for your pocket hole jig workstation at 7:33?
Nah I cut it out on my CNC
I'd love to know where to get quality plywood that doesn't cost a fortune. The ply at Lowes often has huge defects, bowes and voids.
I did a video on 4 things new woodworkers don't know LOL Check it out!
I’d argue pocket holes and dados are completely unnecessary in general cabinet building. Just screw through the sides using the countersink bit. Maybe a couple of brad nails first to help hold in place if you like. Then screw your back on which if cut square will pull the cabinet square
Yeah just depends on the application. I did mention that screwing into the face is a good way to go if the application is right and they won't be seen.
Excellent❤❤ 100
What blade do you use in your tracksaw?
Depends on what I'm cutting. Plywood I use a higher tooth count blade, everything else I use the stock blade that comes with the saw
@@MWAWoodworks Any brand preference on the higher count?
All mine are Festool blades
what do you called that finish plywood sheet?
Finished plywood 🤣
@@MWAWoodworks 🤣lol? where can buy that?
You're local plywood distributor or cabinet supplier will carry it
Does Norm Abram know you stole his plywood spacer hack for the drawer slides?
Haha great minds think alike! 😂
Someday you’ll learn that making separate toe-kicks is an easier method.
I started making my own kitchen cabinets and that was one of my main takeaways from other UA-cam channels like Sedgetools and Brents Woodworking. It’s so easy to level the toe kick platform instead of each cabinet.
It took me about 30 years to finally try separate toe-kicks. Being stuck in that "rut" cost me hundreds of hours of frustration, time and money. I first tried it on my neighbor's garage cabinets. DUH!! I never went back to the old way. Thx.
Only if you're ganging a run of cabinets together. Otherwise it's a waste of time.
@HeadBroski generally speaking it is easier to level 1 piece of wood than it is to level a bunch of separate pieces of wood.
and so you can save more money
👍🏼👍🏼👍🏼👍🏼👍🏼😎
I must be insane, because I 45 the corners of my edge banding with an olfa so they fit together. Too finicky?
efficient, cost-effective (yes), strength of phs (not an issue in this application). What about elegance?
Elegance matters if you're making a Krenov cabinet, not common kitchen cabinets.
@@MWAWoodworks There we disagree. I think build elegance is more about the craftsman than the piece. I use phs from time to time, but honestly I never found the joinery nearly as appealing as using dowels or tenons. There's something about building quality pieces, no matter their intended use. My $0.02
No worries. I just disagree that pocket holes make it less quality. I've made cabinets with my domino and with my pocket hole jig. They look and function identically, no difference in quality and any user of the cabinets would never know what joinery was used to build them.
Where is your fall protection?
My what? 😂
What is your got to tool for removing planks from pallets?
I don't use pallets
I find that Rockler is full of gimmicky little things that people think they can't do without, but that's just my view. - Chris
Yeah some things are brilliant and some are trying to be brilliant when there's no need
Fyi on all easy carry handles - getting up steps does not work. You have to press the thing all the way over your head. Without steps, yes. Industrial jointer, table saw and then just a few more thousand for the rest. Then you need a wide open shop space. At that point you are 50 and if you didnt find a wife and make some babies you now instead have a garage full of tools and the Merc sits in the driveway all winter.
That American adhesion to the imperial system is why you think three-quarter inch plywood is undersized. Plywood is usually 18mm, which is 0.7 of an inch, not 0.75. The answer is to buy an 18mm router bit.
18mm is not the answer to anything. US ply is well over 18mm, more like 18.5mm and the Baltic birch I get from Europe is consistently 17.75mm
Plywood is given a nominal dimension whether that be 3/4 or 18mm. In both cases the actual plywood is smaller. Just like a 2x4 is actually 1.5x3.5
Why? Because mistakes are very expensive now. That and a helping of the sunk cost fallacy.
Twenty three thirty seconds. How do you work on these measurements?!
you round up to 3/4 and move on 😀
You were doing great right up until you said "Pocket Screws". I find the lock miter to be quick and the strongest.
Btw, if you are a multi media worker and you weld, you probably already have several magnetic triangles you can use for the stops. However if the table is aluminum eerht...no go. You can opt for a suction cup gripper like you use to pick up sheet goods and glass panes.
There is something to be said as a matter of pride and accomplishment for making your own custom jigs. By the way KREG did not sponsor these comments.
A lock miter router bit is as expensive as a kreg jig and less versatile. And KREG didn't sponsor this comment either 🤣
I hate my gator lilft and never use it. It's just not a omfy way to carry plywood. Unless you're going to build a tonne of cabinets, you dont need a track saw at all and can do just fine with a very cheap diy version
How do you carry it then?
You’re handling the plywood too many times, put one corner against the fence and lift the opposite bottom corner and make your cut, I would cut it right after taking it out of your truck. You should look into building separate toe kicks, you walk into the kitchen level all the kicks and start putting cabinets on them.
thanks for the advise LOL
@@MWAWoodworks no problem, I am a fine woodworker that’s retired now, I’m just saying what works for me. I’m also 70 and can still cut 3/4 MDF with no problems. Have a great day
There is a huge difference between building a few cabinets for your shop and being a cabinet maker. You do need a table saw, no matter how much you are getting paid to sell track saws.
lol paid to sell track saws? OK.
Never give ground to the metric Karens of the world. You are the Jason Bourne of the imperial system. 👍
The Cricut Mini is perfect for egde banding and not as cumbersome as an iron.
Ahhh I'll have to check that out!
@@MWAWoodworks Yeah, I was suprised. Had my iron, dropped it the shop one last time and had the mini for T's and hats and stuff. It worked so much better. It's smaller, fits perfect over 3/4", has a cool little stand to put in on when it's hot, has a small footprint on my workbench meaning I don't bump into the hot iron anymore and it's also perfect for dents. A little water over the dent, a piece of teflon heat protector and bye-bye dent.
Now to go see if my wife already has one for her Cricut 😂😂😂
@@MWAWoodworks If she doesn't already have one, it might make a fine gift! 😉