How Diesel Generator LOP sensors working | How to connect sensor to pressure gauge & DSE controller
Вставка
- Опубліковано 28 вер 2024
- How diesel generator low oil pressure sensor is working and how to connect pressure sensor to pressure gauge in generator panel and also how to connect it to deep sea controller also explain in this video. So please watch the video completely and support our channel.
How Automatic voltage regulator workings| How to connect AVR to DG wiring diagram
• How Automatic voltage ...
How DG deep sea controller working | How to do wiring from deep sea controller to DG
• How DG deep sea contro...
Electrical Switch Gear basics
• Electrical Switch Gear...
How Cathodic protection system working |Types |Application
• How Cathodic protectio...
#DGpressuresensor #Howpressuresensorworking
#howtoconnectpressuresensortogauge
#lubeoilpressuresensor
Very good explained 😊😊
Good morning sir now i am newly watching your channel please can you tell me where to connect oil pr switch in 7310dse
Super thank u..
Thanks for your comments and keep support our channel
Hey sir, my oil gauge has two symbols on the back, I and U, which one is the signal symbol?
Thank you very much. You have one of the methods of explaining with visuals .
Assalammu alaikkum, Hope you are doing good ,I have a clarify on DG to fuel tank. How do my fuel pump automatically on if my DG tank had low fuel .Please clarify me. Which device I have to use for this activity.
I am doing good and thanks and fuel pump is controlled by 12v fuel solenoid and it has interlock with low fuel sensor and if tank reach that low level then it will trip the DG. And if you want detail operation of fuel pump in sha allah i will make separate video for that
@@electricalmastarokay
Sir my question po? Ano PO bha cause NG Wala pong rpm, pompatak po Ang low oil pressure
Altyazilar Türkçe çevirisi yok maalesef
In the automatic generator, the sensor stops when it fails. Is it possible to temporarily trick the sensor with resistance and use it?
Thanks for your comments and i would not recommend this tricks because it would be danger to equipment and personal safety
Thank you
can i use voltmeter for test
HI Ammar,
For measurements you have to use only pressure gauges
Thank you
Electrical Mastar Team
Same make on fuel.temp sensor
Thanks for your comments Mr. Dharmesh, ya sure soon i will make it those videos. Keep support our channel
Thank you
Dear sir ,
I have a 400 kva bertolis eco 40 generator and cursor13 engine when I charge it deep sea after a charge of more than 50%
I receive a message displayed on the screen
ECU AMBER Warning high or short voltage check engine SPN65619, IMF 3 OC 196 .
what is mean.
Best regards
Hindi bol bhai
I’m sorry but is so hard to understand what u saying 😅
how to connected all sensor and what is name all and what purpose to use and how many and how to testing every one and connected plz plz
Hi Ammar,
These are the sensors mostly we been used in DG
Oil Pressure
Engine Temperature
Coolent level sensor
Diesel level sensor
Thank you
Electrical Mastar Team
The +ve can’t be connected straight to the battery Sir otherwise the gauge will permanently be ON.
I will suggest to use the fuel output
If the genset is turned off the gauge also goes off
Thanks for your comments and i agree with you
Keep support our channel
Thank you
It’s a pleasure Sir
@@electricalmastar then why you have not corrected it even after 11months ???? this is false info.
Sir i have a Question regarding the DSE panel Pin Code . I have panel 8610 module its locked how to delete the pin code ? Please guide me how to solve this problem .
Hi
Thanks for your comments and if you want to reset pin then you have to connect your module to PC through dse software you can change it
How to connect single wire lop sensor with deep sea module.
Hi salman,
Thanks for your comments, if you connect single wire sensor means you need additionally single wire sender unit also connect to deep sea controller
For connection you can check my another deep sea connection video
Thank you
Pls share in hidi Vedic
if you have programe of perkins 1300 series please help and troubleshooting manual thanks
Hi Ammar,
Could you tell me your controller model number then can i can check
Keep support our channel
Thank you
Electrical Mastar Team
30min working gantantra come low pressure alarm in
I'm
*Change pressure sensor
*Change oil
What's problem sir
Sir who to bay pass oil sancer 710 model gearnater contoler plz sir tel me
Very nice.
Hi sir, in 3 wire terminal for shut off fuel solenoid how to connect in deep sea controller, ty
Hi, I'm trying to configure the pressure and temperature sensors but the software keeps writing that the computer and module are not connected. I checked the USB cable and it works well. How do I make sure I connected the two correctly?
San pd bilihin ang ganyang pyesa need ko para sa generator nmn
7310 deep sea.
24 no DG cable used in deep sea 48 no pin.but there has no another connection analog input like-14 to 20 pin in deep sea
What is the function of DG cable number 24 which has been attached to pin number 48 of the panel??
Thank you for your comments Mr. Madhav saha, i am not get yours question clearly could you send the exact drawing then i will try it
Thank you
@@electricalmastar May I have your email id?
May I have your email id?
electricalmastar@gmail.com
😍😍😍😍
How to bypass oil sensor?
Sir explain A m f connection & function with D/g
Thank you for your comments,
You mean Auto main failure connection
@@electricalmastar yes
Hi
Auto main failure already i posted one video please check here
ua-cam.com/video/17FyXFWRT34/v-deo.html
It could be helpful for you
Thank you
Thanks for the knowledge that you share ❤️
How to fuel del press sens lo
I like the explanation
Thanks for your comments and keep support our channel
K.19.oil.perashrr.sencer
Thanks
Brilliant Video!
Thanks dear
From Iraq well done
Thank you and keep support our channel
My greeting for you
please do one video on the DG wiring & troubleshoot
Thanks for your comments and sure i will make separate video for your request
Thank you and keep support our channel
Excellent! Thanks for sharing sir!
Please halep to problem digital infut f