Thanks. This helped a lot. I think I broke one thing but that was my fault because I didn’t pull like you said. I replaced both speakers and hoping to replace the ones in the back too
I found it UN-necessary to remove the several ELECTRICAL CONNECTORS / Wiring Harnesses from the DOOR LOCK & WINDOW BUTTONS instead I just pried the two black clips out of the VALANCE Cover & Yes the the BIG Rectangular BLACK Control Module will fit through the OPENING / HOLE & Thanks for the NOTE on the Door Light --- my BULB had been burned out the DECADES that I have owned the TRUCK :-) LOL Now I have a light ! Thanks
nice video...I wish you could have gone into even further detail as to how to remove the connectors...I just didn't see what I needed to see to do it correctly...ended up busting off part of the power lock connector unfortuantely
Worked great but don't miss lining up the plastic post just in front of the door latch. I broke one tab removing the panel and one more replacing it due to missing that door latch post part. Also, go see the video on how to remove the window crank if you don't have power windows. But all in all, this is a great video. And now I can open the door from inside after replacing the door handle. Thank you.
You’re welcome. I’m glad you were able to do it without too much trouble. I just made a video about how to replace the back speakers on my Chevrolet truck. That is a much harder job, so I just decided to cut holes in front of the speakers and put grills over the new speakers.
Them damn things are are agervating it’s easy to change the handle it’s just the door trim piece. I watched another video a guy said to put a bend in the rod that goes to the door opener that would help the Handel get more leverage to open the door. I think it was the danninator
my door panel is sagging and flapping out, lower tab pins missing, hard to close door so fassen in place with duct tape. I think you just showed me how to fix the problem thx cmc
Whenever I have to remove a door panel on my 1997 GMC pickup, this is my go to video. Thanks.
You’re welcome
Very helpful, had to replace the speakers in the doors so thanks for the thorough guide
Glad it helped!
you do the most random how to's I love it
+Tsunamoo Thanks! I just shoot video of whatever's broken.
So good explanation, right to the point. I'm gonna do it right now in my 97 Silverado. Thank so much for sharing my friend! Greetings from Argentina!
Thanks. This helped a lot. I think I broke one thing but that was my fault because I didn’t pull like you said. I replaced both speakers and hoping to replace the ones in the back too
You’re welcome.
Very good video short sweet to the point normal dude and just the right amount of info not over done at all thx
Glad it helped
I found it UN-necessary to remove the several ELECTRICAL CONNECTORS / Wiring Harnesses from the DOOR LOCK & WINDOW BUTTONS
instead I just pried the two black clips out of the VALANCE Cover
&
Yes the the BIG Rectangular BLACK Control Module will fit through the OPENING / HOLE
&
Thanks for the NOTE on the Door Light --- my BULB had been burned out the DECADES that I have owned the TRUCK :-) LOL
Now I have a light !
Thanks
yeah it feels like there breaking there actually just snapping in half !
Thanks much.. That was Very clear and informative
How did you get it off up by the top of the dash
Thanks for showing me so I didn't break it all to pieces like I usually do !
You’re welcome
nice video...I wish you could have gone into even further detail as to how to remove the connectors...I just didn't see what I needed to see to do it correctly...ended up busting off part of the power lock connector unfortuantely
Thank you. I appreciate the helpful video.
Great instructions 👍
Thanks
Thankyou just used this video.
You’re welcome
I need to know how to get the door panels off with the door closed
Great video. Thanks.
You are welcome!
Worked great but don't miss lining up the plastic post just in front of the door latch. I broke one tab removing the panel and one more replacing it due to missing that door latch post part. Also, go see the video on how to remove the window crank if you don't have power windows. But all in all, this is a great video. And now I can open the door from inside after replacing the door handle. Thank you.
You’re welcome. I’m glad you were able to do it without too much trouble. I just made a video about how to replace the back speakers on my Chevrolet truck. That is a much harder job, so I just decided to cut holes in front of the speakers and put grills over the new speakers.
Why do my clips (panel holders) don't stay in place and keep popin out every time i open my door??
They are probably broken. You may have to buy replacements.
@@hoohoohoblin I ordered brand new ones..... and found out my door is not lining up ,(have to replace hinges's pins.)🤗🤗
Thank you very much.
You are welcome!
Thank you, big help.
You’re welcome
Them damn things are are agervating it’s easy to change the handle it’s just the door trim piece. I watched another video a guy said to put a bend in the rod that goes to the door opener that would help the Handel get more leverage to open the door. I think it was the danninator
Thanks.
Bros got the Rockford speakers.
Thank you!!!
You're welcome!
my door panel is sagging and flapping out, lower tab pins missing, hard to close door so fassen in place with duct tape. I think you just showed me how to fix the problem thx cmc
You’re welcome.
Thanks!
You’re welcome
Dude thanks mom sata Don't quit day job
Ha I didn't break my front tabs Lol
Lucky!
J
I hate that sound!