My grandfather worked on the Golden Gate bridge. The story he handed down about the name was there was a guy on the ground with a rivet forge. Two guys on top would be lining up the beams with the spud wrench and the one guy with heavy gloves would yell "HOT POTATO" and the guy on the forge would throw a red hot rivet up to the guys up top. Mr. Heavy gloves would catch it and jam it in the hole and the other guy had the rivet hammer and they would set the rivets.
Funny this video came up today in my recommended...my buddy gave me a spud wrench a week ago and I threw it in the back of my truck. 2 days later I was working on the front end of a mustang and was having trouble lining up the lower control arm bolts and I remembered the wrench in my truck. Saved my ass. You rock!
Proto makes spud wrenches all the way down to sizes about the length of your hand for smaller nuts and bolts, not just structural steel sizes like us ironworkers use, Klein spuds are about the lowest quality there is although they're the most common ones used by ironheads, if you ever see one that's stamped AB right at the base of the jaw grab it, AB stands for American Bridge, although they still exist they're a shell compared to when they were the ironworking division of US Steel (circa 1915 to 1980), they were so big they made their own spud wrenches in AB's fab shop in Ambridge Pa (Ambridge is short for American Bridge and is the town outside of Pittsburgh that their fab shop was in), they're highly prized by retired ironworkers who worked for AB back in their glory days, and if you find one in decent shape you can get a few hundred dollars from one of those guys who wants one for a keepsake, Bethlehem Steel also made their own for their ironworkers but I've never heard of someone paying $$$ for one although that's not to say they won't.
Ironworkers Local 3 right here. So, Essential Craftsman. You have spud wrenches and wear Sears Die Hard boots. Are you sure you're not a closet ironworker? 😊
Use mine every day! Usually if its a face connection, we put the spud in, bolt the opposite side, then walk out and cut the crane loose. Knife connections, however, spud in, then you're good to cut the crane loose. The most important thing in ironworking is cost. That crane is the most expensive machine on site. It has to constantly be moving for it to be worth running and operating. Swing the crane! In the time it takes to swing, you can secure the beam with bolts, remove your spud and get to the next connection.
I have a spud ratchet, but when we do ironwork I like to use a bull pin which accomplishes the same thing as a spud but it can be driven in with a sledge or hand sledge.
Hey! I moved to a new city in the dead of winter last year and got on a framing crew, worst winter in 20-30 years around here. Never did production wood framing and stumbled across your channel and learned a few things so I could get up to speed before my first day, (been in the trades my whole life mostly doing remodel work and electrical in CA prior). Just wanted to say thank you for what you do. Stuck it out through the winter framing and realized it wasn't for me. The few things i could retain from you through an overnight tutoring session got me an hourly rate higher than anyone on that crew and more importantly helped me get established out here so I could find something more my speed and provide for my family and love what I do. I erect pre-fab metal buildings now and run a crew of 4-6 guys. Guys like you, guys like my dad, my uncle, yall are a dying breed. I hope I have this much volume and quality to pass on to the people that come after me some day to keep this dream alive. Thank you sir.
My grandfather had a bunch of spud wrenches from when he was a tug boat mechanic. I remember one summer we used some as tent spikes to hold down the guide ropes for the gazebo at a family gathering. He also used them for removing knockouts on electricians boxes, this brought back some good memories, guess I need to go buy myself a few :) Thank you
I have a 1 5/8" spud wrench. Not only is the spud end useful the wrench end can be used to tweak twisted 2 by material when framing. It even fits over treated lumber which is usually 1 9/16" thick until it dries out.
As a plumber, I love my spud wrench. Most plumbers I work around have no clue what it's for, but they think it's dangerous. I used to do a lot of mechanical flange work, and found it essential.
Never knew what a spud wrench was for! Thanks! One great use for a standard crescent wrench end is to thread bolt hooks in and out of posts when hanging a farm gate. Put the hole on the end of the wrench over the "hook" and you have great leverage in turning the bolt.
Watching the Iron workers connecting the columns and beams on the new UBER building in San Francisco was Eye opening. The " connectors" would dance on the beams, receive a beam the from the crane use a SLEVER bar to line up the holes put two bolts in ,Tighten with the spud wrench and move on. The speed and agility and no fear is really impressive. Not to mention the guy's at the bottom in the " Iron pile" hooking the beams up to the crane.
I was a bridge carpenter years ago... I bought a Crescent adjustable spud wrench when I was a 1st period apprentice, then bought a Snap-on spud ratchet just before I made journeyman. The ratchet cost $109.99 ten years ago, and purchased the extra set of guts for it. Everyone else talked about how more it cost than the Klein one, until I was able to get 3 clicks out of it in a tight spot... The Klein didn't even get one click.
I love mine, my brother gave it to me . I never appreciated it until I used it once and now I couldn’t live without it. Motor mounts, front end work on suspension, keeping a wheel aligned while you stab the axel on a motorcycle plus the crescent wrench applications . Man I tell you it’s like a third hand that knows how to get the job done right. Thanks for the videos love to see great craftsmanship.
Your videos are awesome! I love the feeling of these videos, it's like sitting in the shop with my grandfather when I was young and he would do the same thing, not only tell you but show you...
A old ironworker told me the reason they call them spud wrenches is the spike part was also used to hold their potatoes over a fire during lunch to cook their spuds. No joke. Don't know how true that is.
@@smash507 Exactly, a spud is originally a pointed tool used to poke a hole in the dirt to plant a seed, most early ironworkers were Irish immigrants or 1st generation descendants of them so it's not hard to put together how they got their name. Local 489 Scranton, always boomin' out, Pittsburgh, Harrisburg, Detroit etc etc...
Last time I used one of those, I was doing helicopter iron work at Kahua Ranch Wind Farm of the Big Island of Hawaii. We'd be up on a hundred thirty foot tower and a helicopter would bring over a sixty watt alternator, gearbox and triple fourteen foot bladed turbine unit. There would be a couple ropes hanging down off of it and we'd pull the helicopter and stub down to the top of the tower. Spud wrenches in the bolt holes, climb up, unhook from the helicopter and start bolting up the legs. Best darn job I ever had. Work at six thousand feet and sleep on the beach.
I don't rightly know. This was in very late 1985 and I got the suggestion for the job while staying for one night at the Captain Cook Hotel from a guy who turned me on to some really nice weed. LOL
2:00 Electrician here, we use the end of crescent wrenches quite often for various tasks. Torquing allen keys and straightening out kinked wire are the most common.
I first learned about spud wrenches in the oil patch. Oh that little opening on the end of a crescent is excellent for opening needle valves extremely useful.
I’m a concrete man out of NY and a spud/crescent is on my belt every day sometime even a spud ratchet. One of the most versatile tools I’ve ever Hd the pleasure of learning to use
I work as a dairy technician/installer, building milking parlours, stalling and gates. You are right my DeWalt spud was 3x more then a standard wrench but it's always at my side.
During my Navy days (ret'd in'92), we used to make quite a few of the marlinspike/crescent wrench tools for the boatswainmates aboard ship. The most common size were the type they could put in a sheath on their belts. A "spud wrench" was a tool we used (aboard ship again) to remove/install the threaded fitting in urinals/toilets. Thanks for the memories, EC. :)
Hello, Sir. Love your content, currently my favorite page. Thought I'd comment to let you know Amazon has a pretty sharp bead on you. Meaning, I'd put on my wish list White Ox work gloves, and wouldn't you know, a few days later I received a standard "you may be interested in" email from Amazon, and on the list: Stiletto titanium framing hammer, skillsaw wormdrive circular saw, large (monster) prybar, Spencer logger's tape! They've got an algorithm with your name all over it. (Hope you're compensated!)
Something useful on the regular crescent: When throwing out sheet goods (Metal roof and concrete decking, in my case), you'll find the old timers often grind down the end into a thin wedge for separating the layers of deck from the bundle. And ironworkers call it a bull pin instead of a Marlinspike, just a semantics thing.
Grinding your spud is actually a bad thing. I was taught never to put heat to your wrench, connecting bar, or any tool for that matter. It weakens the iron and could cause the tool to fail. This is important because occasionally, you may need to stand on a wrench or bar to work the iron. I know what you're talking about in reference to the wedge tip. You get that same result by simply hitting the end with your beater to form the tip. A bullpin is tapered from the tip to the end where you hit. A marlinspike is tapered at the tip, similar to a pencil. The full taper is important for getting your pin out of the hole. A bullpin is meant to stop at some point and comes out the same way it went in. A drift pin or barrel pin is meant to go all the way through the hole. Typically, to drive it fully, you're going to need a B&O, which is like punch with a handle. And if you decide to have a great day, then you'll break out the "hell dog" if the B&O isn't enough. While using any type of pin, it's a good idea to slap some wax on it before sending it.
I used spud wrenches and shop-made drift pins to line up pipe flanges on large steam, condensate, and water line repairs and maintenance, working as a Stationary Engineer. most trades have unique tools to simplify life. Flange spreader is another interesting and really helpful tool most folk would not figure out till it was seen in practice.
Building towers for years, that wrench was in my tool belt every day. Retired, not much use for one , but there were many a time , I sure which I had mine back. Great tool. Thanks for asking.
Always thought I was a good handyman... I've learned so much on these videos... I'm glad I recently discovered UA-cam Keep up with the great videos I find a new episode every day to watch
A short story about my first experience with a spud wrench. 1977 and I had bluffed my way on a job and was hanging ninety feet up on the side of a grain bin. The guy beside me asked where my spud wrench was, I thought it was one of those muffler bearing or sky hook things, so I said, I got a spud wrench right here in my pants, you wanta grab it for me ! Damed near got me fired the first day on the job ! 😣 Thanks for sharing and take care.
Yup... ive used the end hole for many things that are tricky to get a grip on! You can torque the handle of another tool or a bar over the handle of another tool, etc. Or thread in a hooked lag bolt
zipde doda That's actually where they got there name from, according to what folklore I've heard on site. Irish immigrants apparently used a similar implement to dig up potatoes back in the home country; when they came to America (specifically New York by way of Ellis Island) and entered into the trades, Iron was in big business. One of us Micks got the idea of welding a wrench head on the end of a "spud digger", hence "spud wrench".
Outstanding. For two years of my undergrad work (BS Biology) I worked as an iron worker, in welding, fabrication and erection. The Spud Wrench was one of our most valuable tools for erection....along with a ComeAlong. ;) Lot of tension build into a lot of those buildlings. We fabricated and erected anything up to 3 stories. My favorite job, next to running a soda fountain in high school and working in the Cabinet Shop at Grand Rapids Chair Company during a couple other years of college.
Grew up on a small erecting crew, family business, our logo is a spud wrench and an i beam lol, and those guys are invaluable. Pro tip, carrying one alows you to line up and hold one hole, carrying two alows you to wrack the connection anywhere you want it. I work in a fab shop as a welder making medium sized steel beams now, and a pair of spuds are still one of my favorite tools.
The hole on the end of a crescent is great for going over the short end of an Allen key in line with its rotation and using it to add torque and leverage . Especially when you've got the long end down somewhere you can't reach and the fastener is more then hand tight. It adds much needed leverage in those situations to break the bolt loose. Something you cannot do with a spud. Although spuds are useful for many other things. Especially lining up flanges in pipe work or a bolted door plate. Etc.
I love my adjustable spud wrenches. I got an imported one for $9 at Tractor Supply. It has a little hammer face, and you can reverse the jaw to make it like a pipe wrench. Then I got a Klein adjustable spud wrench at an antique shop. This tool is a must have!
If you are hanging a livestock gate, and your using pins for hinges - once started you take a cresent wrench end hole and put the leg through and turn/screw the pin all the way into the post or beam for the gate. Dad taught me that.
I got my 1st spud wrench back in the mid 60's when I went to work for an Elevator co. and still have it to this day. and would not part with it for anything. even though its not an adjustable, I keep it around for the Spud part of lining things up as you mentioned. . Everything old again is new again. what goes around comes around. doesn't it. Thanks for the reminder/tip
I love my spud wrench!! I use one at work all the time. We have camlock brass fittings for hoses and the locking handles get corroded over time. The spud wrench is perfect for leverage in getting those handles undone. Also, I use it as a crude hammer whenever I need to do some light(emphasis) hammering. I'm also a industrial/marine electrician so I can use the crescent end to tighten up ground bolts.
Learned of this tool from a mechanic, sorta learned it's use in the ironworker's hands from a video made by "Smarter Every Day" (I think) about building grain bins. Couldn't tell you how many times I've used it, in all manner of likely "incorrect" methods, to put stuff in the perfect spot. Also, it works very well as a short prybar to shuffle heavy stuff a small distance and cheater tubes work extremely well with the spud end.
I’m a Concrete form setter and use both a crescent wrench and a spud crescent wrench. I use the eye of the nail hanger to bend pencil rods as soon as I activate the cat’s head. I also use it to break off snap ties.
Thanks for this. After my father died I inherited one on these and always wondered what it was for as it always looked a little dangerous. Keep up the good content.
I occasionally do steel work but I do pre cast all the times and I use my spud maily as a wedge to hold my joints, to turn braces and of course use the crescent end ... best tool i own
Old tower climber here. Used to carry one of those plus an adjustable along with a bull pin and a mini sledge. Oh and a bottle of gator aid. You will get strong building towers carrying all that weight every day. Best job I ever had, got to see most of the US and several places outside the country. Met some really good guys and worked with one of the best crews ever. Only downside to building towers or any kind of high steel is your body doesnt last as long. Your joints will start to go, especially your lower back, then your knee's and shoulder's.
Have a spud wrench with 1/2 and 3/4 drive rachets on the end. It was 8 dollars at tractor supply. I use the spike ends to align bolt holes on plastic granulators, and It is much lighter than my other 3/4 drive which is nice for working overhead inside extrusion molding machines
I discovered these a couple years ago when I was at our local structural steel place to pick up some scraps for blacksmithing. At the same time I discovered that Klein makes drift/bull pins, which turn out to work perfectly well for drifting holes in hot steel.
spud wrench and a 3 lb engineer hammer head made up a tool i used in a pipe foundry for setting the rollers on the casting machines. you used the hammer portion to slam loose the big wing nuts, then the wrench end to adjust the rollers. then the hammer again to slam the wing nut tight again.
Iron-worker local 11 here. Use my spud everyday. Do not apply heat to your spud wrenches or connecting bar. It will harden the steel and can break on you when you least expect it. Such as don’t use a grinder on it. Great tip, you can file down the tip of the spud wrench with a manual filer to a flat tip. Great doe getting it into tight spots or opening metal boxes. Also another great tool is a connecting bar. It’s like a pry bar but in the right hands. It’s a pry bar and the whole 9 yards.
Been plumbing all my life, we always refer to a smooth mouth pipe wrench as a “spud wrench” in reference to “spuds” like the fixture connection fittings for flushometers, where you can’t foul the finish but need a lot of torque .
I made one of these with an 8 inch long Crescent wrench because you can't buy a short one anywhere. Shortest one you can buy is like 10-11 inches and so I made a 8-9 inch one that fits in my pocket perfect. I recommend grinding down the end into a flat head and it makes it way more useful. I'm not an Ironworker and I mainly work on stuff below 1" bolts so it's perfect size.
For God's sake, if you decide to get a spud wrench, do not buy a cheap one. Some of the cheapees coming out of China are over hardened and will snap under mild stress. I saw this happen on a job site. Potentially a very dangerous incident.
StutleyConstable I wonder if they over harden, or just plain don't heat treat them at all. I've seen a lot of chinesium tools shatter on first use. You can feel how brittle they are in your bare hand.
You might have a point there. I had a friend who purchased a set of three aligning pins from Harbor Freight. They were zinc plated and he broke them all within a few hours. Looking at the broken ends it was obvious they had not been heat treated. There was no indication of tearing. It looked more like the sort of snap you get from cast iron.
My Pop was a Millwright by trade, used one quite a lot. As a child I found it to be much better of a lawn dart than the screwdrivers were. These days I find all sorts of uses from auto fab to leatherwork, and everything in between. Probably my favorite tool in the shop.
Have an 8 Inch one and Love it. Next one I am going to get A 1/2 -3/8 ratchetwrench spud. I like the fact that you do not have to lug a big piece of pipe for a cheater. By the way, my heart skipped a beat and got dizzy when you brought out the Marlinspike thought you going to use it.! Thumbs up!.
I'm a crane operator and a rigger and we call it a "spud" too. Invaluable tool for a rigger trying to lineup bolt holes with the bolts. If I'm erecting anything with my crane I carry spud wrench, Burke bar, and a bull pin.
yes, i know what they are call and have used them also nice to have around i have both of them nothing works like a spud wrench everybody should one. thamk you for the video.
Welder, here. Spud wrenches are some of the most useful tools within the steel trades. Get some decent ones, and you’ll have excellent tools that will come in handy time and time again for years.
They also lend to being used in conjunction with almost any diameter pipe to use as a “cheater bar” to break off those tight connection which need more leverage.
My grandfather worked on the Golden Gate bridge. The story he handed down about the name was there was a guy on the ground with a rivet forge. Two guys on top would be lining up the beams with the spud wrench and the one guy with heavy gloves would yell "HOT POTATO" and the guy on the forge would throw a red hot rivet up to the guys up top. Mr. Heavy gloves would catch it and jam it in the hole and the other guy had the rivet hammer and they would set the rivets.
Thats funny
Props to your grandfather, he built a helluva bridge for the ages. Those old school craftsmen are were amazing.
I wish we still built em like that
Funny this video came up today in my recommended...my buddy gave me a spud wrench a week ago and I threw it in the back of my truck. 2 days later I was working on the front end of a mustang and was having trouble lining up the lower control arm bolts and I remembered the wrench in my truck. Saved my ass. You rock!
Proto makes spud wrenches all the way down to sizes about the length of your hand for smaller nuts and bolts, not just structural steel sizes like us ironworkers use, Klein spuds are about the lowest quality there is although they're the most common ones used by ironheads, if you ever see one that's stamped AB right at the base of the jaw grab it, AB stands for American Bridge, although they still exist they're a shell compared to when they were the ironworking division of US Steel (circa 1915 to 1980), they were so big they made their own spud wrenches in AB's fab shop in Ambridge Pa (Ambridge is short for American Bridge and is the town outside of Pittsburgh that their fab shop was in), they're highly prized by retired ironworkers who worked for AB back in their glory days, and if you find one in decent shape you can get a few hundred dollars from one of those guys who wants one for a keepsake, Bethlehem Steel also made their own for their ironworkers but I've never heard of someone paying $$$ for one although that's not to say they won't.
That's just what I was thinking it would be good for, or the suspension bushes on a multi-link set up can be a pain in the ass, I feel this would help
Ironworkers Local 3 right here.
So, Essential Craftsman. You have spud wrenches and wear Sears Die Hard boots. Are you sure you're not a closet ironworker?
😊
Use mine every day!
Usually if its a face connection, we put the spud in, bolt the opposite side, then walk out and cut the crane loose. Knife connections, however, spud in, then you're good to cut the crane loose.
The most important thing in ironworking is cost. That crane is the most expensive machine on site. It has to constantly be moving for it to be worth running and operating. Swing the crane! In the time it takes to swing, you can secure the beam with bolts, remove your spud and get to the next connection.
makattak88 well put. 17 yrs in local 396 St. Louis, Mo
makattak88 well said. 17 yrs in local 396 St. Louis, Mo
Local 759 Thunder Bay. Thanks Brother!
I have a spud ratchet, but when we do ironwork I like to use a bull pin which accomplishes the same thing as a spud but it can be driven in with a sledge or hand sledge.
I sure do like this guy! Practical advice and a friendly attitude. Knowing it all with out being a "know-it-all!"
Another thing I have learned from this channel.
I am honestly glad I found your channel sir.
Thank you.
Hey! I moved to a new city in the dead of winter last year and got on a framing crew, worst winter in 20-30 years around here. Never did production wood framing and stumbled across your channel and learned a few things so I could get up to speed before my first day, (been in the trades my whole life mostly doing remodel work and electrical in CA prior). Just wanted to say thank you for what you do. Stuck it out through the winter framing and realized it wasn't for me. The few things i could retain from you through an overnight tutoring session got me an hourly rate higher than anyone on that crew and more importantly helped me get established out here so I could find something more my speed and provide for my family and love what I do. I erect pre-fab metal buildings now and run a crew of 4-6 guys. Guys like you, guys like my dad, my uncle, yall are a dying breed. I hope I have this much volume and quality to pass on to the people that come after me some day to keep this dream alive. Thank you sir.
My grandfather had a bunch of spud wrenches from when he was a tug boat mechanic. I remember one summer we used some as tent spikes to hold down the guide ropes for the gazebo at a family gathering. He also used them for removing knockouts on electricians boxes, this brought back some good memories, guess I need to go buy myself a few :) Thank you
I love old tools. My Grandad was a mechanic on steam shovels (40,s & early 50,s). He had tools I could not pick up (too heavy). Miss you Grandad !
I have a 1 5/8" spud wrench. Not only is the spud end useful the wrench end can be used to tweak twisted 2 by material when framing. It even fits over treated lumber which is usually 1 9/16" thick until it dries out.
This gentleman is one of those person that you wanna Pay attention when he specks
He got a lot knowledge Great videos
As a plumber, I love my spud wrench. Most plumbers I work around have no clue what it's for, but they think it's dangerous. I used to do a lot of mechanical flange work, and found it essential.
Never knew what a spud wrench was for! Thanks! One great use for a standard crescent wrench end is to thread bolt hooks in and out of posts when hanging a farm gate. Put the hole on the end of the wrench over the "hook" and you have great leverage in turning the bolt.
Watching the Iron workers connecting the columns and beams on the new UBER building in San Francisco was Eye opening. The " connectors" would dance on the beams, receive a beam the from the crane use a SLEVER bar to line up the holes put two bolts in ,Tighten with the spud wrench and move on. The speed and agility and no fear is really impressive. Not to mention the guy's at the bottom in the " Iron pile" hooking the beams up to the crane.
I was a bridge carpenter years ago... I bought a Crescent adjustable spud wrench when I was a 1st period apprentice, then bought a Snap-on spud ratchet just before I made journeyman. The ratchet cost $109.99 ten years ago, and purchased the extra set of guts for it. Everyone else talked about how more it cost than the Klein one, until I was able to get 3 clicks out of it in a tight spot... The Klein didn't even get one click.
I love mine, my brother gave it to me . I never appreciated it until I used it once and now I couldn’t live without it. Motor mounts, front end work on suspension, keeping a wheel aligned while you stab the axel on a motorcycle plus the crescent wrench applications . Man I tell you it’s like a third hand that knows how to get the job done right. Thanks for the videos love to see great craftsmanship.
Your videos are awesome! I love the feeling of these videos, it's like sitting in the shop with my grandfather when I was young and he would do the same thing, not only tell you but show you...
A old ironworker told me the reason they call them spud wrenches is the spike part was also used to hold their potatoes over a fire during lunch to cook their spuds. No joke. Don't know how true that is.
Wildman of the Wynooch
I think another name for a pry bar is a spud bar. I assumed spudding something was moving it in small increments
True
as an old i/w someone was pulling your leg,
@@smash507
Exactly, a spud is originally a pointed tool used to poke a hole in the dirt to plant a seed, most early ironworkers were Irish immigrants or 1st generation descendants of them so it's not hard to put together how they got their name.
Local 489 Scranton, always boomin' out, Pittsburgh, Harrisburg, Detroit etc etc...
In fact, “spud” as slang for “potato” came from the tool used to plant potatoes, not the other way around. The tool name preceded the vegetable name.
your report has a wonderful way of taking me down from the disreality of the run-of-mill U tube crap
Last time I used one of those, I was doing helicopter iron work at Kahua Ranch Wind Farm of the Big Island of Hawaii. We'd be up on a hundred thirty foot tower and a helicopter would bring over a sixty watt alternator, gearbox and triple fourteen foot bladed turbine unit. There would be a couple ropes hanging down off of it and we'd pull the helicopter and stub down to the top of the tower. Spud wrenches in the bolt holes, climb up, unhook from the helicopter and start bolting up the legs. Best darn job I ever had. Work at six thousand feet and sleep on the beach.
Mickey Xtian To whom do I send my resume?
I don't rightly know. This was in very late 1985 and I got the suggestion for the job while staying for one night at the Captain Cook Hotel from a guy who turned me on to some really nice weed. LOL
Jacob wind energy, based at the time out of Minneapolis MN
Never knew about Spud wrenches till I started replacing guard rail. Simply an invaluable tool for many jobs.
2:00 Electrician here, we use the end of crescent wrenches quite often for various tasks. Torquing allen keys and straightening out kinked wire are the most common.
Essential craftsman I love watching your videos. You have a life time of real knowledge. And are exceptionally comfortable in front of a camera.
I was introduced to a spud wrench when I was putting up my steel building. Went and bought one for myself and it's been very handy to have.
I first learned about spud wrenches in the oil patch. Oh that little opening on the end of a crescent is excellent for opening needle valves extremely useful.
I’m a concrete man out of NY and a spud/crescent is on my belt every day sometime even a spud ratchet. One of the most versatile tools I’ve ever Hd the pleasure of learning to use
I work as a dairy technician/installer, building milking parlours, stalling and gates. You are right my DeWalt spud was 3x more then a standard wrench but it's always at my side.
During my Navy days (ret'd in'92), we used to make quite a few of the marlinspike/crescent wrench tools for the boatswainmates aboard ship. The most common size were the type they could put in a sheath on their belts. A "spud wrench" was a tool we used (aboard ship again) to remove/install the threaded fitting in urinals/toilets. Thanks for the memories, EC. :)
On the back pocket of carhartt bib overalls there is a “micro hammer loop” just for the spud wrench
Hello, Sir. Love your content, currently my favorite page. Thought I'd comment to let you know Amazon has a pretty sharp bead on you. Meaning, I'd put on my wish list White Ox work gloves, and wouldn't you know, a few days later I received a standard "you may be interested in" email from Amazon, and on the list: Stiletto titanium framing hammer, skillsaw wormdrive circular saw, large (monster) prybar, Spencer logger's tape! They've got an algorithm with your name all over it. (Hope you're compensated!)
Something useful on the regular crescent: When throwing out sheet goods (Metal roof and concrete decking, in my case), you'll find the old timers often grind down the end into a thin wedge for separating the layers of deck from the bundle.
And ironworkers call it a bull pin instead of a Marlinspike, just a semantics thing.
Marlinspikes were commonly used for splicing wire rope.
Grinding your spud is actually a bad thing. I was taught never to put heat to your wrench, connecting bar, or any tool for that matter. It weakens the iron and could cause the tool to fail. This is important because occasionally, you may need to stand on a wrench or bar to work the iron. I know what you're talking about in reference to the wedge tip. You get that same result by simply hitting the end with your beater to form the tip.
A bullpin is tapered from the tip to the end where you hit. A marlinspike is tapered at the tip, similar to a pencil. The full taper is important for getting your pin out of the hole. A bullpin is meant to stop at some point and comes out the same way it went in. A drift pin or barrel pin is meant to go all the way through the hole. Typically, to drive it fully, you're going to need a B&O, which is like punch with a handle. And if you decide to have a great day, then you'll break out the "hell dog" if the B&O isn't enough. While using any type of pin, it's a good idea to slap some wax on it before sending it.
Always handy for pinning your trailer hitch too! Used them setting double wides many years ago.
I used spud wrenches and shop-made drift pins to line up pipe flanges on large steam, condensate, and water line repairs and maintenance, working as a Stationary Engineer. most trades have unique tools to simplify life. Flange spreader is another interesting and really helpful tool most folk would not figure out till it was seen in practice.
I use that hole in a cresent to tighten large screwhooks also grabs the end of a combination wrench for extra leverage, nice to hang up also.
The hole is also good to put a bend in large wire (ie electric service entrance).
Building towers for years, that wrench was in my tool belt every day. Retired, not much use for one , but there were many a time , I sure which I had mine back. Great tool. Thanks for asking.
Always thought I was a good handyman... I've learned so much on these videos... I'm glad I recently discovered UA-cam Keep up with the great videos I find a new episode every day to watch
A short story about my first experience with a spud wrench.
1977 and I had bluffed my way on a job and was hanging ninety feet up on the side of a grain bin. The guy beside me asked where my spud wrench was, I thought it was one of those muffler bearing or sky hook things, so I said, I got a spud wrench right here in my pants, you wanta grab it for me !
Damed near got me fired the first day on the job ! 😣
Thanks for sharing and take care.
Thanks for taking me back, again, Scott!
The hole on the end of a crescent wrench is great for bending offsets on threaded rod
& good for screwing gate hinges into a gate post..........
Yup... ive used the end hole for many things that are tricky to get a grip on! You can torque the handle of another tool or a bar over the handle of another tool, etc. Or thread in a hooked lag bolt
Damn,and I been usein the dam thing to dig up my taters.
zipde doda Silly boy...it's for tightening your taters.
I thought it was for tightening curly fries!
Not to be confused with a spud wench. She dunks the fries...
zipde doda That's actually where they got there name from, according to what folklore I've heard on site.
Irish immigrants apparently used a similar implement to dig up potatoes back in the home country; when they came to America (specifically New York by way of Ellis Island) and entered into the trades, Iron was in big business. One of us Micks got the idea of welding a wrench head on the end of a "spud digger", hence "spud wrench".
zipde doda I
Outstanding. For two years of my undergrad work (BS Biology) I worked as an iron worker, in welding, fabrication and erection. The Spud Wrench was one of our most valuable tools for erection....along with a ComeAlong. ;) Lot of tension build into a lot of those buildlings. We fabricated and erected anything up to 3 stories. My favorite job, next to running a soda fountain in high school and working in the Cabinet Shop at Grand Rapids Chair Company during a couple other years of college.
I bought a spud cresent wrench at a garage sale one time. I always wondered why the handle was shaped the way it was. Thank you for the education!
Grew up on a small erecting crew, family business, our logo is a spud wrench and an i beam lol, and those guys are invaluable. Pro tip, carrying one alows you to line up and hold one hole, carrying two alows you to wrack the connection anywhere you want it. I work in a fab shop as a welder making medium sized steel beams now, and a pair of spuds are still one of my favorite tools.
The hole on the end of a crescent is great for going over the short end of an Allen key in line with its rotation and using it to add torque and leverage . Especially when you've got the long end down somewhere you can't reach and the fastener is more then hand tight. It adds much needed leverage in those situations to break the bolt loose. Something you cannot do with a spud. Although spuds are useful for many other things. Especially lining up flanges in pipe work or a bolted door plate. Etc.
I got one of these about five years ago and they are most underrated tools but I use them all the time now.
I love my adjustable spud wrenches. I got an imported one for $9 at Tractor Supply. It has a little hammer face, and you can reverse the jaw to make it like a pipe wrench. Then I got a Klein adjustable spud wrench at an antique shop. This tool is a must have!
i built one out of a 15" craftsman cresent wrench and some 1" hex bar in 1981.
looks real good in my tool box!
Really enjoy your videos about unique tools.
If you are hanging a livestock gate, and your using pins for hinges - once started you take a cresent wrench end hole and put the leg through and turn/screw the pin all the way into the post or beam for the gate. Dad taught me that.
I don't get it. Not well explained.
I have been seeing these wrenches a lot, lately. I couldn't figure out what they were used for. Awesome video.
I got my 1st spud wrench back in the mid 60's when I went to work for an Elevator co. and still have it to this day. and would not part with it for anything. even though its not an adjustable, I keep it around for the Spud part of lining things up as you mentioned. . Everything old again is new again. what goes around comes around. doesn't it. Thanks for the reminder/tip
I love my spud wrench!! I use one at work all the time. We have camlock brass fittings for hoses and the locking handles get corroded over time. The spud wrench is perfect for leverage in getting those handles undone. Also, I use it as a crude hammer whenever I need to do some light(emphasis) hammering. I'm also a industrial/marine electrician so I can use the crescent end to tighten up ground bolts.
Spud wrench is one of those great inventions. C resent wrenches used to have a box end wrench of some size in the hole we now use to hang them up.
Learned of this tool from a mechanic, sorta learned it's use in the ironworker's hands from a video made by "Smarter Every Day" (I think) about building grain bins.
Couldn't tell you how many times I've used it, in all manner of likely "incorrect" methods, to put stuff in the perfect spot. Also, it works very well as a short prybar to shuffle heavy stuff a small distance and cheater tubes work extremely well with the spud end.
I got a spud wrench. I picked it up at a yard sale for $5. I had no idea what the spike was used for. Thanks. That was very educational.
I’m a Concrete form setter and use both a crescent wrench and a spud crescent wrench. I use the eye of the nail hanger to bend pencil rods as soon as I activate the cat’s head. I also use it to break off snap ties.
Never thought I'd see this video anywhere! Great video!!!
Thanks for this. After my father died I inherited one on these and always wondered what it was for as it always looked a little dangerous. Keep up the good content.
“Desperation becomes the mother of invention” I love it
I use mine all the time for lining up elect gear shipping sections or bussing ties. Great wrenches and I like the feel of one in my hand
I occasionally do steel work but I do pre cast all the times and I use my spud maily as a wedge to hold my joints, to turn braces and of course use the crescent end ... best tool i own
So much good information on this channel.
Old tower climber here. Used to carry one of those plus an adjustable along with a bull pin and a mini sledge. Oh and a bottle of gator aid. You will get strong building towers carrying all that weight every day. Best job I ever had, got to see most of the US and several places outside the country. Met some really good guys and worked with one of the best crews ever. Only downside to building towers or any kind of high steel is your body doesnt last as long. Your joints will start to go, especially your lower back, then your knee's and shoulder's.
Known as a podger wrench/spanner in the UK
Loving your channel
Some great videos here
Ironworkers local 736 Hamilton, Ontario, Canada!! Big fan of your channel. Impressed by your choice of boot as well!
I like the hole in the wrench. I use them to put pressure with my socket wrench. Very handy .
Best channel I've subscribed to for a long time. Keep up the great work!
First I've heard of one too. Actually, I've used the loop on crescent wrench for fastening lag screw eye bolts and hooks in lumber.
Have a spud wrench with 1/2 and 3/4 drive rachets on the end. It was 8 dollars at tractor supply. I use the spike ends to align bolt holes on plastic granulators, and It is much lighter than my other 3/4 drive which is nice for working overhead inside extrusion molding machines
Right on bro
Good vid of yours...
I love these spud wrenches, they come really handy most of the time...
Be safe out there
Regards
I use a pegboard to put my crescent wrenches, regular wrenches, screwdrivers, everything, its so great.
I discovered these a couple years ago when I was at our local structural steel place to pick up some scraps for blacksmithing. At the same time I discovered that Klein makes drift/bull pins, which turn out to work perfectly well for drifting holes in hot steel.
Thanks for this as I found one in my late Fathers tool box and till now wasn't quite sure of it's purpose.
spud wrench and a 3 lb engineer hammer head made up a tool i used in a pipe foundry for setting the rollers on the casting machines. you used the hammer portion to slam loose the big wing nuts, then the wrench end to adjust the rollers. then the hammer again to slam the wing nut tight again.
As an engineer in the Merchant Marine I've used a spud wrench many times. Especially on steam ships.
I found a large one of those along side the road years ago. It is my go to wrench and is always at the top of the pile
A dramatic soliloquy about a mundane item. Brilliant. This reminds me of the old Quaker oats ads.
One of the first wrenches I knew was a Spud wrench. Pops was an iron worker and I still have one of his wrenches.
Iron-worker local 11 here. Use my spud everyday. Do not apply heat to your spud wrenches or connecting bar. It will harden the steel and can break on you when you least expect it. Such as don’t use a grinder on it. Great tip, you can file down the tip of the spud wrench with a manual filer to a flat tip. Great doe getting it into tight spots or opening metal boxes. Also another great tool is a connecting bar. It’s like a pry bar but in the right hands. It’s a pry bar and the whole 9 yards.
Been plumbing all my life, we always refer to a smooth mouth pipe wrench as a “spud wrench” in reference to “spuds” like the fixture connection fittings for flushometers, where you can’t foul the finish but need a lot of torque .
I made one of these with an 8 inch long Crescent wrench because you can't buy a short one anywhere. Shortest one you can buy is like 10-11 inches and so I made a 8-9 inch one that fits in my pocket perfect. I recommend grinding down the end into a flat head and it makes it way more useful. I'm not an Ironworker and I mainly work on stuff below 1" bolts so it's perfect size.
thats awesome! my dad had a bunch of these and I never knew what they were for. I used them alot to pry things haha worked great. Cool vid!!!!
For God's sake, if you decide to get a spud wrench, do not buy a cheap one. Some of the cheapees coming out of China are over hardened and will snap under mild stress. I saw this happen on a job site. Potentially a very dangerous incident.
StutleyConstable
I wonder if they over harden, or just plain don't heat treat them at all. I've seen a lot of chinesium tools shatter on first use. You can feel how brittle they are in your bare hand.
You might have a point there. I had a friend who purchased a set of three aligning pins from Harbor Freight. They were zinc plated and he broke them all within a few hours. Looking at the broken ends it was obvious they had not been heat treated. There was no indication of tearing. It looked more like the sort of snap you get from cast iron.
It's only chinese steel that lacks all quality. Usually steel from Taiwan and Japan are pretty good, and of course U.S. made if you can find it.
Sheffeild steel
StutleyConstable
Klein
I do like Cresent brand spud-crescent, they don't open up or spread like the Klein
Walk into any Collison Center and you'll see custom tools like this. Awesome video! I always just called it, "that thing".
My Pop was a Millwright by trade, used one quite a lot. As a child I found it to be much better of a lawn dart than the screwdrivers were. These days I find all sorts of uses from auto fab to leatherwork, and everything in between. Probably my favorite tool in the shop.
Have an 8 Inch one and Love it. Next one I am going to get A 1/2 -3/8 ratchetwrench spud. I like the fact that you do not have to lug a big piece of pipe for a cheater.
By the way, my heart skipped a beat and got dizzy when you brought out the Marlinspike
thought you going to use it.! Thumbs up!.
My spud wrench is 15 years old. Great tool steel, awesome pry bar, I use it often. Don't go to a job site without it.
Love mine for suspension work
Very cool. Hadn't heard of a spud wrench before. Will have to add it to the "tools to find/buy/make list"
All the best,
John
I'm a crane operator and a rigger and we call it a "spud" too. Invaluable tool for a rigger trying to lineup bolt holes with the bolts. If I'm erecting anything with my crane I carry spud wrench, Burke bar, and a bull pin.
yes, i know what they are call and have used them also nice to have around i have both of them nothing works like a spud wrench everybody should one. thamk you for the video.
Great suggestion, and good advice.
Welder, here. Spud wrenches are some of the most useful tools within the steel trades. Get some decent ones, and you’ll have excellent tools that will come in handy time and time again for years.
Haha 😂 in England we call it a podger! Used exactly as u said, for aligning bolt holes in jobs, quick simple n really useful
I've put lighting trusses together for MANY major stage shows using a spud wrench.
cool... didn't know that.. Thank You
We used to call it a Podger when I was an apprentice in the 50's
Tony Thomason still
Call them a podger. Although they have a ratchet on one end and a spike on the other
Definitely came in handy when i was putting up steel buildings
They also lend to being used in conjunction with almost any diameter pipe to use as a “cheater bar” to break off those tight connection which need more leverage.
I have one,always thought it was homemade.Great video