Killer Dowel Pin KDP Install Video
Вставка
- Опубліковано 17 жов 2024
- In this video we fix the Killer Dowel Pin or KDP found on the Cummins 6BT and 4BT engines. We utilize a BD Diesel KDP Kit.
Doing a DIY diesel swap? We’ve got you covered!
GM DIESEL CONVERSION
adventurevehic...
LAND CRUISER DIESEL CONVERSION
adventurevehic...
UNIVERSAL DIESEL CONVERSION
adventurevehic...
Find some of our favorite gear on our Amazon shop: amzn.to/3J3KihN
#AmazonAssociate - We earn a small portion from qualifying purchases.
Thanks for your support!
Bought Felpro complete seal kit( Includes seal tool) from Napa. Saved $80.00,
Part number?
6:59 Dust Shield.
I thought that was an oil slinger?
Whatever it is, is this item install on the inside or outside of the seal? Do I put the ring on the shaft before I put the cover on (oil slinger) or put the ring on the shaft after I put the cover on (dust shield)?
18 ft lbs on mostly everything , your welcome
Maybe I'm not seeing things right....but this engine appeared to need the "stair stepped" tab and not the flat tab as shown. As you can see when he tightened the bolt down it bent the tab greatly out. There are differences in these B engines. Some have a flat surface across to the pin bore and on some the pin bore is in a different plane than the flange face of the bolt. While this may still work OK...it's not right in my book.
Besides the tab...old timers used to tap the pin back to bottom out, shoot some wicking loctite green in the bore and peen the bore inside with a punch. Just as effective and free...besides the gasket and crank seal. This is how I fixed mine. Some but not all 24V ISB 5.9L's had a lip edged inner bore so the pin couldn't come out. But only visual verification can tell you if you have this case cover. No serial number or date can prove it as verified by Cummins.
هناك توقيت عام تشترك فيه كل المحرمات يغني عن كل الشروحات
It will work just fine the way he did it. Some people just get a fender washer, cut it into the shape of the tab, bolt it on and then tap it down like he did. As long as it prevents the dowel pin from coming out, it's all good.
Where can I get that bracket for alternator and ac
cool vid id like to see more vids on the 6bt ive been kicking around the idea of doing a 6bt conversion in a military surplus cucv m1008 pickup
Anyone know roughly how much this would cost at a shop?
very well instructed video! Thank you
if the balancer isnt notched how do you know which of the 4 positions it goes in ?
well, it's symmetrical so technically it doesn't matter, but either memory or mark one hole with white out or something
hey does anyone know if you can do this KDP fix without have to jack the engine out of the truck? I was thinking you could probably take the grill off and radiator and whatever else so you can see, let me know. thanks
yup, you dont have to pull the motor, go look it up on "cummins forum"
alright that's what I thought, ill check it out then and then when I go to do it I might as well hit the seals too
yes you can easily do a kdp in the truck
What years is the killer dowel pin an issue?
Through the 24 valve models. 2002 is the last year
'89 to '02. From what I've read the '94 to '02s are a little more likely to vibrate out, but it sometimes happens in '89 to '93 12v's too.
Thank you sir
If the injector pump is making a racket
Thanks,
use a socket over the installed tool so it can be hammered in evenly.
Claudio Del Castillo know where I might find a 3 inch socket anywhere else than in a heavy mechanics shop?
Next time put a flat piece of wood over the seal install tool and hammer on the wood
does this apply to a 2006 5 9 Cummins
No this is only for 12 Valves (89-98)
i believe the KDP was fixed by cummins in 2003
12v and 24v, '89 to '02.
Killer pin trouble ended in 2002 models ( 24 valve ) It had begun in the mid year of year 98. I’m talking about the 5.9- 24 valve. It so happens I have the 98.5, 24 valve and its killer pin was approximately half way out. And now I’m having a problem getting it to go back in.
Lol🤣🤣🤣